Porting Edelbrock 6037 heads, Thoughts?

mufflerboy · 11-26-2001, 08:26 PM

I have a small oil leak from my head gasket that want to fix. While the heads were off I was thinking of having them ported. Would it be worth it to gasket match and give them a general clean up, I m also going to send in my Cobra lower if I do it. I also think that my valve springs might be getting weak, so I'll replace them too.Is there much power gain from doing this will it be worth the time and money.

Five0 · 11-26-2001, 10:00 PM

The heads are where you make all the power and if ported properly yes it will make a worthwhile difference.

6T9PONY · 11-26-2001, 10:10 PM

DO IT!!! But make sure you take the things to a quality shop that has reputable workers and equipment. You will get large power gains and should help your ET a lot!!!!

NO SLO PK · 11-26-2001, 11:29 PM

I also have a set of Edelbrocks that I wanted gasket matched...the machinist laughed at me. Apparently, Edelbrock heads are already matched pretty well to the gaskets. The Felpro 1250 intake gasket and 1415 exhaust fit pretty well.

If you're talking about porting and bowl work, then yes, it will help as long as you have the right combination of parts. You will probably lose some port velocity which will kill power down low, but your gears are good so hopefully you can get into the power band sooner.

Yeah, I'd get them cleaned up but maybe not go overboard. That's just me though.

Five0 · 11-26-2001, 11:46 PM

Actually as long as he does not get too carried away with the port size he should not loose any bottom end, in fact he will probably pick up in the whole rpm range. It depends on what he has done. I would just recommend having the heads ported but don't get too carried away with it. Maybe an econo port or a stage 2 port job at most unless you want to move your power up high and loose a little low end.

302man · 11-27-2001, 10:47 AM

Mine are ported and polished. They work pretty well. I want to move up on the flow numbers , so I will be taking mine off and flow benching them to make a compairison.

11-26-2001, 08:26 PM	#1
mufflerboy Registered Member Join Date: Jan 1999 Posts: 126	Porting Edelbrock 6037 heads, Thoughts? I have a small oil leak from my head gasket that want to fix. While the heads were off I was thinking of having them ported. Would it be worth it to gasket match and give them a general clean up, I m also going to send in my Cobra lower if I do it. I also think that my valve springs might be getting weak, so I'll replace them too.Is there much power gain from doing this will it be worth the time and money. __________________ 93 coupe

11-26-2001, 10:00 PM	#2
Five0 Registered Member Join Date: Apr 2000 Location: middleburg, fl, usa Posts: 1,134	The heads are where you make all the power and if ported properly yes it will make a worthwhile difference. __________________ James Cox RHC Member #44 nochevy@hotmail.com 1991 Mustang LX Dart iron eagle block, 4340 28oz 347 crank, 4340 h-beam rods, probe ultra light pistons canfield heads “race ported by Brent Frazier”, solid roller cam and lifters “custom grind”, kooks 1 7/8" race headers, and much more. Engine built by Brent Frazier.

11-26-2001, 11:29 PM	#4
NO SLO PK Registered Member Join Date: Mar 1999 Location: Arcadia, CA, USA Posts: 731	I also have a set of Edelbrocks that I wanted gasket matched...the machinist laughed at me. Apparently, Edelbrock heads are already matched pretty well to the gaskets. The Felpro 1250 intake gasket and 1415 exhaust fit pretty well. If you're talking about porting and bowl work, then yes, it will help as long as you have the right combination of parts. You will probably lose some port velocity which will kill power down low, but your gears are good so hopefully you can get into the power band sooner. Yeah, I'd get them cleaned up but maybe not go overboard. That's just me though. __________________ Russ L '91 LX - 331 w/ Procharger '03 Cobra Convertible - Pullied '94 Lightning '65 Mustang Coupe Last edited by NO SLO PK; 11-26-2001 at 11:38 PM..

11-26-2001, 11:46 PM	#5
Five0 Registered Member Join Date: Apr 2000 Location: middleburg, fl, usa Posts: 1,134	Actually as long as he does not get too carried away with the port size he should not loose any bottom end, in fact he will probably pick up in the whole rpm range. It depends on what he has done. I would just recommend having the heads ported but don't get too carried away with it. Maybe an econo port or a stage 2 port job at most unless you want to move your power up high and loose a little low end. __________________ James Cox RHC Member #44 nochevy@hotmail.com 1991 Mustang LX Dart iron eagle block, 4340 28oz 347 crank, 4340 h-beam rods, probe ultra light pistons canfield heads “race ported by Brent Frazier”, solid roller cam and lifters “custom grind”, kooks 1 7/8" race headers, and much more. Engine built by Brent Frazier.

11-27-2001, 10:47 AM	#6
302man Registered Member Join Date: Jul 1999 Location: INDIANAPOLIS Posts: 404	Mine are ported and polished. They work pretty well. I want to move up on the flow numbers , so I will be taking mine off and flow benching them to make a compairison. __________________ old S trim combo 10.13@ 135 New YS combo = 680RWHP (no times)

11-26-2001, 10:10 PM	#3
6T9PONY All about the Windsor. Join Date: Feb 2000 Posts: 2,052	DO IT!!! But make sure you take the things to a quality shop that has reputable workers and equipment. You will get large power gains and should help your ET a lot!!!!

Thread Tools
Show Printable Version Email this Page
Display Modes	Rate This Thread
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode	Rate This Thread:

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Edelbrock heads	Scrapla	Windsor Power	4	03-28-2004 08:39 AM
Edelbrock Victor racing heads #7721	SmokinStangGT	Windsor Power	4	05-09-2003 07:20 AM
edelbrock performer rpm heads	hippi97	Windsor Power	2	04-01-2001 08:40 PM
Is the true about Edelbrock heads with TFS intake?	gt93mustang	Windsor Power	14	03-06-2001 07:01 PM
Edelbrock heads and compression	flagg	Windsor Power	10	02-10-2001 11:14 AM