question on EDEL heads ...6022

vande97 · 02-15-2002, 10:30 PM

well i just got a set of these heads they are stud mount heads. I talked to a guy and he told me that i need longer pushrods to run these heads then i talked to another guy that said i would not need them, I dont have the heads on yet and have not got harden pushrods yet so before i order new rods i want to know if i need a diffrent lenght rod or will the stock lenght be ok, Also if anyone might know the size(lenght) that i would need that would be a big help. I do have a B cam also.

thanks alot!!!

PKRWUD · 02-16-2002, 06:45 AM

Because there are other factors involved, like head gasket thickness, rocker arm type, lifter condition, milled surfaces, etc., the only way to do it right is with an adjustable pushrod, used to measure, then order.

Take care,
-Chris

vande97 · 02-16-2002, 01:09 PM

cool thanks, I will get one of thos and check it out!

86GT · 02-16-2002, 03:19 PM

Checking is the best way to know for sure. I did, and found that with my 6032s and rocker arms/head gaskets, I just needed a stock length pushrod. But if I didn't check I could have been way off. Definitely worth doing.

02-15-2002, 10:30 PM	#1
vande97 Registered Member Join Date: Jan 2001 Location: okemos Posts: 205	question on EDEL heads ...6022 well i just got a set of these heads they are stud mount heads. I talked to a guy and he told me that i need longer pushrods to run these heads then i talked to another guy that said i would not need them, I dont have the heads on yet and have not got harden pushrods yet so before i order new rods i want to know if i need a diffrent lenght rod or will the stock lenght be ok, Also if anyone might know the size(lenght) that i would need that would be a big help. I do have a B cam also. thanks alot!!!

02-16-2002, 06:45 AM	#2
PKRWUD Junior Member Join Date: Mar 1999 Location: Ventura, California Posts: 8,981	Because there are other factors involved, like head gasket thickness, rocker arm type, lifter condition, milled surfaces, etc., the only way to do it right is with an adjustable pushrod, used to measure, then order. Take care, -Chris __________________ Webmaster: Rice Haters Club Jim Porter Racing Peckerwoods Pit Stop Support Your Local RED & WHITE!

Thread Tools
Show Printable Version Email this Page
Display Modes	Rate This Thread
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode	Rate This Thread:

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
New Heads. Any Tips	66StangGuy	Classic Mustangs	5	09-15-2003 08:20 PM
GT-40 Heads question....	Bluefox91LX	Windsor Power	7	11-21-2002 02:58 PM
Another heads question	90LxDroptop	Windsor Power	3	11-10-2002 02:45 AM
Heads and Cam....tough question	cyberstang5.0	Windsor Power	2	12-07-2001 09:22 AM
A general question about heads!	Thad	Windsor Power	0	10-10-2001 11:17 AM

02-16-2002, 01:09 PM	#3
vande97 Registered Member Join Date: Jan 2001 Location: okemos Posts: 205	cool thanks, I will get one of thos and check it out!

02-16-2002, 03:19 PM	#4
86GT Sniffed too much n20 Join Date: Oct 1998 Location: Ont, Canada Posts: 1,018	Checking is the best way to know for sure. I did, and found that with my 6032s and rocker arms/head gaskets, I just needed a stock length pushrod. But if I didn't check I could have been way off. Definitely worth doing.