help crankshaft dampner stuck!!

TOM90LX · 07-12-2002, 10:20 PM

I was putting back the crank shaft dampner after doing a cam install and heads install and I could not turn the crank after tightening down the bolt on the dampner to draw it closer to the front engine cover.

However, if I take the dampner off and install just the bolt, I can turn the crank rather easily.

Did I do something wrong? Could the timing cover be misaligned?? How do I figure out if that is the problem?

I need to figure this out.. someone give me advice please!!

Tom

PKRWUD · 07-12-2002, 10:51 PM

Lightly scuff the inside of the balancer, where it goes over the crank, with some 4-O steel wool, then generously add some anti-seize to the crank snout, and do the best you can. Then, get a longer bolt that has the same size and thread pitch as the one that holds the balancer in place, and use it to move the balancer in. If you use the stock bolt, you won't get enough threads, and will strip out the end of the crank. Not alot of fun, trust me.

Take care,
-Chris

TOM90LX · 07-13-2002, 06:22 AM

I can get the dampner on the snout all the way.. the problem is I cannot turn the engine over after its on. I cant rotate the crankshaft. I can only rotate the crank when I don't have the balancer on and only a bolt through the end of the snout.

Any suggestions? Other people say I might have a wrong bolt in the timing cover that is hitting the back of the dampner?

Tom

07-12-2002, 10:20 PM	#1
TOM90LX Registered Member Join Date: Jul 2001 Location: Hightstown, NJ Posts: 14	help crankshaft dampner stuck!! I was putting back the crank shaft dampner after doing a cam install and heads install and I could not turn the crank after tightening down the bolt on the dampner to draw it closer to the front engine cover. However, if I take the dampner off and install just the bolt, I can turn the crank rather easily. Did I do something wrong? Could the timing cover be misaligned?? How do I figure out if that is the problem? I need to figure this out.. someone give me advice please!! Tom __________________ 90 LX 5.0 Convert. Moroso cold air ,73 mm MAF, 65 mm FMS TB, Cobra intake, adj fuel pres reg. 24# inj, 155lph fuel pump, accel supercoil, electric fan, 180 deg thermostat, 3 row HD radiator, march underdrive pulleys, GT40X heads, 1.7 Roller Rockers, Mac 1 5/8 shorty headers, hi-flow 2.25" cats, dynomax superturbo 2.5" cat back, g-brace, strut tower brace, Global West TBF-1 lower control arms, caster/camber plates, Steeda rear adj swaybar, GlobalWest Traclink torque arm, SVO 73mm caliper pistons, stainless steel braided hose brake lines, 17 inch 5 star wheels, Tokico Illumina shocks/struts, Global West specific rate springs, flaming river steering shaft. FMS Cobra clutch, Steeda adj. clutch cable, 85 GT halo headrests, white face gauges, white face a/c panel, leather brake handle, leather shift knob, Ford Racing custom leather interior, Pony emboridered floor mats, Saleen Alum pedals. Cobra A/C knobs

07-12-2002, 10:51 PM	#2
PKRWUD Junior Member Join Date: Mar 1999 Location: Ventura, California Posts: 8,981	Lightly scuff the inside of the balancer, where it goes over the crank, with some 4-O steel wool, then generously add some anti-seize to the crank snout, and do the best you can. Then, get a longer bolt that has the same size and thread pitch as the one that holds the balancer in place, and use it to move the balancer in. If you use the stock bolt, you won't get enough threads, and will strip out the end of the crank. Not alot of fun, trust me. Take care, -Chris __________________ Webmaster: Rice Haters Club Jim Porter Racing Peckerwoods Pit Stop Support Your Local RED & WHITE!

07-13-2002, 06:22 AM	#3
TOM90LX Registered Member Join Date: Jul 2001 Location: Hightstown, NJ Posts: 14	I can get the dampner on the snout all the way.. the problem is I cannot turn the engine over after its on. I cant rotate the crankshaft. I can only rotate the crank when I don't have the balancer on and only a bolt through the end of the snout. Any suggestions? Other people say I might have a wrong bolt in the timing cover that is hitting the back of the dampner? Tom __________________ 90 LX 5.0 Convert. Moroso cold air ,73 mm MAF, 65 mm FMS TB, Cobra intake, adj fuel pres reg. 24# inj, 155lph fuel pump, accel supercoil, electric fan, 180 deg thermostat, 3 row HD radiator, march underdrive pulleys, GT40X heads, 1.7 Roller Rockers, Mac 1 5/8 shorty headers, hi-flow 2.25" cats, dynomax superturbo 2.5" cat back, g-brace, strut tower brace, Global West TBF-1 lower control arms, caster/camber plates, Steeda rear adj swaybar, GlobalWest Traclink torque arm, SVO 73mm caliper pistons, stainless steel braided hose brake lines, 17 inch 5 star wheels, Tokico Illumina shocks/struts, Global West specific rate springs, flaming river steering shaft. FMS Cobra clutch, Steeda adj. clutch cable, 85 GT halo headrests, white face gauges, white face a/c panel, leather brake handle, leather shift knob, Ford Racing custom leather interior, Pony emboridered floor mats, Saleen Alum pedals. Cobra A/C knobs

Thread Tools
Show Printable Version Email this Page
Display Modes	Rate This Thread
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode	Rate This Thread:

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Wipers are stuck on	CONVGTMUSTANG	Windsor Power	3	03-04-2004 02:13 PM
2000 Mustang Crankshaft pulley	zzsmart	Modular Madness	1	11-15-2002 08:28 PM
t5 stuck in between 3 and 4th	Brian88	Windsor Power	3	11-26-2001 12:21 AM
Crankshaft Pulley(Vibration Damper) Removal	Dray	Windsor Power	8	10-23-2001 04:46 AM
HELP HELP HELP Stuck in the trunk!	Super_Stang	Windsor Power	5	07-29-2001 11:35 PM