HAL k-member

PONYONE · 07-24-2002, 10:39 PM

Anyone run one of these? Whats involved in swapping it out ? The engine is out of the car right now and I planned on using my stock control arms and struts. Will the stock 83gt c/a's even work?

thanks all

nitrousdave · 07-24-2002, 11:05 PM

I have one on my 85. Your a-arms should work, but if yours is like mine your a-arms will be moved forward 3/4"-1". This could cause tire clearnce problems. I was told by Hal that the k-member was designed to do this, but I've heard from others that their a-arms didn't move. The a-arm issue wasn't really an issue for me since I got Hal's a-arms also and was able to space them back to the stock location. Swapping them out is pretty simple, especially since you have the engine out. 8 bolts, the a-arms, and the steering rack is all that's required to swap it out. Oh and be careful of the springs when your lowering the old one out of the way and getting the springs back in without a motor in the car is a real PITA!!! Hope this helps.

cyberstang5.0 · 07-25-2002, 07:25 AM

I have the Q-A1 K-member and I am about to install it myself

It is not suppose to move the control arms anywhere. It will accept both the stock springs and coil overs. I'm installing it for weight, strength, and it's easier to work around. I'll repost (If I can remember) when I'm done.

nitrousdave · 07-25-2002, 05:46 PM

I would be real interested to see if your a-arms move forward or not because the guy at Hal (QA1) told me they were designed to do just that. Maybe he was blowing smoke up my butt because mine got built wrong or something, but he said they did it to increase the wheelbase a little and improve handling. Who knows??? If you would please post your results.

Just me · 07-26-2002, 12:11 PM

I have a Hal k-member and installed it with a friend. He held the k-member in place while I bolted it up. This is a very light piece. We put a floor jack under the motor while doing the swap but having a chery picker would of made the job easier. Overall it was a simple job. The only trouble was that I had to grind the inside of my a-arms so they wouldn't rub against the k-member. You might not have to do this. I also bought and installed new offset steering rack bushings. When the job was done I was pleased to say the least. It felt like I was driving a V8 honda. The car felt much lighter up front and the steering felt tighter and more responsive. I didn't notice that the a-arms moved foward but I did notice the caster(or camber?) setup had more of an agressive racing look and feel. Also when I lift my hood to show people my goodies, they trip out when all they see is motor and the ground.
It looks like the motor is suspended in air. lol.
Good luck and research is your best weapon for construction.

07-24-2002, 10:39 PM	#1
PONYONE Registered Member Join Date: May 2002 Posts: 23	HAL k-member Anyone run one of these? Whats involved in swapping it out ? The engine is out of the car right now and I planned on using my stock control arms and struts. Will the stock 83gt c/a's even work? thanks all

07-24-2002, 11:05 PM	#2
nitrousdave Registered Member Join Date: Dec 2001 Location: south bend, indiana Posts: 24	I have one on my 85. Your a-arms should work, but if yours is like mine your a-arms will be moved forward 3/4"-1". This could cause tire clearnce problems. I was told by Hal that the k-member was designed to do this, but I've heard from others that their a-arms didn't move. The a-arm issue wasn't really an issue for me since I got Hal's a-arms also and was able to space them back to the stock location. Swapping them out is pretty simple, especially since you have the engine out. 8 bolts, the a-arms, and the steering rack is all that's required to swap it out. Oh and be careful of the springs when your lowering the old one out of the way and getting the springs back in without a motor in the car is a real PITA!!! Hope this helps. __________________ 85 GT 10 pt cage 11.68 to 1 408 windsor ported dart sr's super victor 9 inch w/4.11's bigshot plate turbo 350 trans etc etc

07-25-2002, 05:46 PM	#4
nitrousdave Registered Member Join Date: Dec 2001 Location: south bend, indiana Posts: 24	I would be real interested to see if your a-arms move forward or not because the guy at Hal (QA1) told me they were designed to do just that. Maybe he was blowing smoke up my butt because mine got built wrong or something, but he said they did it to increase the wheelbase a little and improve handling. Who knows??? If you would please post your results. __________________ 85 GT 10 pt cage 11.68 to 1 408 windsor ported dart sr's super victor 9 inch w/4.11's bigshot plate turbo 350 trans etc etc

Thread Tools
Show Printable Version Email this Page
Display Modes	Rate This Thread
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode	Rate This Thread:

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
K Member	65,dohc,project	Classic Mustangs	0	10-06-2004 03:27 PM
tubular k member/ motor mounts?	sn95gt19	Windsor Power	0	12-04-2002 12:05 PM

07-25-2002, 07:25 AM	#3
cyberstang5.0 347ci of HORSE POWER!!! Join Date: Jul 2001 Location: Houston, TX Posts: 1,416	I have the Q-A1 K-member and I am about to install it myself It is not suppose to move the control arms anywhere. It will accept both the stock springs and coil overs. I'm installing it for weight, strength, and it's easier to work around. I'll repost (If I can remember) when I'm done.

07-26-2002, 12:11 PM	#5
Just me Registered Member Join Date: Nov 1998 Location: Miami,Florida Posts: 159	I have a Hal k-member and installed it with a friend. He held the k-member in place while I bolted it up. This is a very light piece. We put a floor jack under the motor while doing the swap but having a chery picker would of made the job easier. Overall it was a simple job. The only trouble was that I had to grind the inside of my a-arms so they wouldn't rub against the k-member. You might not have to do this. I also bought and installed new offset steering rack bushings. When the job was done I was pleased to say the least. It felt like I was driving a V8 honda. The car felt much lighter up front and the steering felt tighter and more responsive. I didn't notice that the a-arms moved foward but I did notice the caster(or camber?) setup had more of an agressive racing look and feel. Also when I lift my hood to show people my goodies, they trip out when all they see is motor and the ground. It looks like the motor is suspended in air. lol. Good luck and research is your best weapon for construction.