Main Girdle is it worth it??

skiwesser · 05-02-2003, 12:48 AM

I'm planning on a rebuild of my motor.

I'll only be doing a .030 overbore w/forged pistons.

I'll prob. stick with my ported E7's for now for $$ reasons

but I may add a mild cam & spray it with about a 150 shot.

What do you guys think about these girdles?

Should I get the rotating assembly balanced?

skiwesser · 05-02-2003, 12:50 AM

The heads were also milled .035

VeNuM · 05-02-2003, 01:09 PM

It doesn't really stiffen the rotating assembly. What it's job is, is that it keeps everything together if there is a failure like cracking a block. Aluminum ones are supposed to be better because they absorb vibrations. Me personally, am putting one on my motor for insurance. ~Brian

05-02-2003, 12:48 AM	#1
skiwesser Registered Member Join Date: Sep 2000 Location: rock hill,S.C. 29730 Posts: 420	Main Girdle is it worth it?? I'm planning on a rebuild of my motor. I'll only be doing a .030 overbore w/forged pistons. I'll prob. stick with my ported E7's for now for $$ reasons but I may add a mild cam & spray it with about a 150 shot. What do you guys think about these girdles? Should I get the rotating assembly balanced? __________________ 88 GT: subs,pullies, 1 3/4 longtubes, flowmasters, AFR 165's,T,F #1 cam,Thyphoon intake, 24# inj., 73mm C&L,65mmT.B., 190LPH pump, Eagle sir rods, forged pistons in a newly rebuilt 306. DYNO TUNED TO 300.97 RWHP 337RWTQ

05-02-2003, 12:50 AM	#2
skiwesser Registered Member Join Date: Sep 2000 Location: rock hill,S.C. 29730 Posts: 420	The heads were also milled .035 __________________ 88 GT: subs,pullies, 1 3/4 longtubes, flowmasters, AFR 165's,T,F #1 cam,Thyphoon intake, 24# inj., 73mm C&L,65mmT.B., 190LPH pump, Eagle sir rods, forged pistons in a newly rebuilt 306. DYNO TUNED TO 300.97 RWHP 337RWTQ

05-02-2003, 01:09 PM	#3
VeNuM Registered Member Join Date: Apr 2002 Location: Downers Grove, IL Posts: 464	It doesn't really stiffen the rotating assembly. What it's job is, is that it keeps everything together if there is a failure like cracking a block. Aluminum ones are supposed to be better because they absorb vibrations. Me personally, am putting one on my motor for insurance. ~Brian __________________ 1989 Black Mustang GT Hatchback, Underdrive Pulles, Electric Fan, Cold Air Intake, Headers, Offroad H-Pipe, Magnaflow catback, Steeda Tri-Ax, Fluidyne Aluminum Radiator, Timing at 14*, 3.73's Coming not so soon: 408w Ricer Hater's Club Member #59

Thread Tools
Show Printable Version Email this Page
Display Modes	Rate This Thread
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode	Rate This Thread:

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Main girdle or windage tray or both?	Fulcrum	Windsor Power	11	11-04-2003 04:51 PM
MAIN GIRDLE	rwebb	Windsor Power	0	03-10-2001 04:04 PM
Main Stud Girdle	IMPULSERACING	Windsor Power	2	02-18-2001 08:15 PM
CAT MAIN GIRDLE?	rwebb	Windsor Power	0	02-14-2001 11:23 PM
Rear Main Seal	diablopony	Classic Mustangs	5	01-15-2001 03:16 PM