Wow a great 12.95....NOT

89fast5oh · 08-11-2004, 02:12 PM

What a disapointment my 1/4 run was. A best of 12.95 @ 114 mph with some 13.40s. What is my problem? I'm running on fairly good tires, (i figure), shifting at 6000. Maybe my car needs a better tune but i just dunno. Fuel pressure is at 40psi and timing is at 16 or 18 i can't remember.
Everything is in my sig and nothing changed. I just figure a 351W should be a bit stronger than that.

88fivepointoh · 08-11-2004, 02:19 PM

um yeah it should be... so its a 351 EFI setup? what injectors, computer, etc.. what gear ratio, intake etc.. give us some specs on your car then I can make a better assessment.

Stang_ROTY · 08-11-2004, 02:20 PM

Hey...don't get bummed out. I'm in the same boat...my best ET is a 12.51, but my MPH is WAYYYYYYYYYY down @ 104-105. Maybe we can figure out something together...did you play with timing yet??

88fivepointoh · 08-11-2004, 02:21 PM

ok stupid me, I just read your profile, you have decent stuff.. I would have to say something is wrong in your timing, 16 should be decent, i would increase your fuel pressure to maybe 45psi, see what happens then, does it feel like its starving out, or strong all the way? Are your tires gripping and how is your clutch, maybe your clutch is slippin. let me know on this..

89fast5oh · 08-11-2004, 02:21 PM

88fivepointoh- All my car info is in my signature.
Stang_ROTY- I havn't really played with my timing and if i did the track is 3hrs away.

89fast5oh · 08-11-2004, 02:27 PM

My clutch is fine from what i can tell and traction is ok. Not the greatest in first, i have to feather it, but just a slight spin into second and away it goes. it doesn't feel like it gives much up top end, but i have always wondered and asked about the stock valve springs that came on older AFR heads. They say there good for .550" lift and i'm right on that, maybe a tinnie bit over, but i don't have coil bind. I've never measured the spring pressure to see if they are good enough tho.

Stang_ROTY · 08-11-2004, 02:28 PM

We have damn near the same setup but I run a C4 and you run the 5 speed. Looks like the 5 speed is better for MPH and the C4 has a more consistent ET...which isn't surprising. No chip? Mine won't hold an idle without a chip. A 12 second street car is not shabby at all.

89fast5oh · 08-11-2004, 02:33 PM

The car runs great, starts up and idles fine everytime. Well maybe 7 out of 10 times anyways. No chip, just the stock AL9 computer. Although it has developed a bit of a off-ilde stummble lately, i wonder if that has anything to do with it?

88fivepointoh · 08-11-2004, 02:40 PM

I would start with an increase of fuel pressure to 45 maybe higher, the track will tell the tale. Then timing and ignition could use to be looked at. what your tune up like? What plugs are you using? Are you running and MSD box, there known for High end cut off issues.. Mine did that.. took me forever to figure it out.

~The Jester~ · 08-11-2004, 03:45 PM

You've got some minor issues. 114 MPH should be at least a 12.20 or so. That means she's making the ponies, but the et is falling off somewhere. Usually the little end of the track, if you're spinning in second you've got traction problems. Run a little less air pressure, get some pointers on "tuning" your upper control arms, and play with the timing. There's is literally TONS of torque hiding in your distributor! I'd be willing to bet your stocker distributor isn't bringing yout total timing in until about 4500 which is waaaaay late, and it's probably only giving you about 30@ total which also sucks. Timing is a "black art" of sorts, and sometimes pricey but it the long run it pays you back 100%.

Start with the little stuff and work your way up. Maybe get some cold air in that motor too. And by the way, a 12 second street car is NOTHING to sneeze at!!!!

88fivepointoh · 08-11-2004, 03:55 PM

Are you running a stock distributor? If so maybe upgrade to a MSD or something..

Capri306 · 08-11-2004, 04:09 PM

Read your spark plugs.
Have you actually checked for coil bind?
Get a custom chip or a twEECer.

Dark_5.0 · 08-11-2004, 05:10 PM

114mph seems about right. What was your 60ft, I am guessing that it sucked.

A high 11 or low 12 should be easy with 114mph.

Were you running slicks?

88workcar · 08-11-2004, 09:26 PM

89fast, you DO NOT have motor issues. TRACTION, 60FT, WHEELIES get it. You must work on these or you will never get a good ET. 114 is 11 sec car.

As much time, effort, and money that you spent on motor, needs to be spent on the CAR. Start with a set of 90/10s.

89fast5oh · 08-11-2004, 11:17 PM

Hey guys, thanks for all the suggestions and input. I'll have to play around with timing, fuel press and see what i can do about the traction.
I made the runs on my McCreary G-60s if any of you are familiar with those ones.
The car is a daily driver and it is really fun to drive and hard to beat might i add.

A side note that may shed some light on the matter that i just remembered, was that a couple months ago i raced a guy in a old dodge duster out on the hiway and beat on him pretty good. He claimed he went 12.20 on slicks last season and has made no changes. We raced from a stop and i beat him, and raced again from a roll and i beat him again. I even noticed that i pulled away and kept slightly pulling from him the whole time we raced.

Its just to me it always seemed like i got pretty good traction, i would like to feel the car on slicks launching at 5500rpm, hahaha

88fivepointoh · 08-12-2004, 02:05 PM

SMOKE THEM DODGES.. Play around with it at the track, I think with a better tire combination you'll get closer to what your looking for.

Stang_ROTY · 08-12-2004, 05:20 PM

I need to make that type of power! My car is setup for ET, but I just need to find the power. What are you using for tires?? What pressure you run them at?

fiveOguy20 · 08-12-2004, 06:36 PM

ya i must agree with everyone that 114 is 11's no doubt cuz im goin 11.90's at 113 so its in there! At this point its all bout traction an driving. good luck

89fast5oh · 08-12-2004, 06:53 PM

Stang_ROTY - I'm using McCreary American Racer G-60 tires. They are actually a Dirt Track tire but have a DOT # so i use them on the street, (not i need DOT tires where i'm from, cheesy cops).
I run them at about 15psi, and they seem to work fairly well, but i guess not good enough for what i want.

68Falcon · 08-12-2004, 09:55 PM

My best is 11.58@115

08-11-2004, 02:12 PM	#1
89fast5oh Registered Member Join Date: Apr 2002 Location: Canada Posts: 56	Wow a great 12.95....NOT What a disapointment my 1/4 run was. A best of 12.95 @ 114 mph with some 13.40s. What is my problem? I'm running on fairly good tires, (i figure), shifting at 6000. Maybe my car needs a better tune but i just dunno. Fuel pressure is at 40psi and timing is at 16 or 18 i can't remember. Everything is in my sig and nothing changed. I just figure a 351W should be a bit stronger than that. __________________ 351W .030", AFR 185s, Crane roller cam-.543" 220 -.562" 228@.050, TFS 351W EFI intake, Billet Roller Rockers, BBK Long Tubes, BBK X- Pipe, Dynomax Race Magnums w/dumps, 30lb injectors, 190lph intank pump, Holley Adjustable FPR, 75mm TB&MA, Underdrive pulleys, Aluminum Rad, Billet Flywheel, McCloud Clutch, World Class T-5, B&M Ripper Shifter 4.10s, McCreary G-60s, Lakewood 90/10s, Comp. Enginering 3 way adjust/rear, Upper and Lower Control arms, Autometer gauges.

08-11-2004, 02:20 PM	#3
Stang_ROTY Registered Member Join Date: Feb 2001 Location: Berkshire County - Massachusetts Posts: 735	Hey...don't get bummed out. I'm in the same boat...my best ET is a 12.51, but my MPH is WAYYYYYYYYYY down @ 104-105. Maybe we can figure out something together...did you play with timing yet?? __________________ Red 1993 GT Street Machine Best E.T. - 12.41/Best MPH = 108 Engine is a 1969 351 block w/393 stroker kit. Dynamic Roller Myte C4, 8 pt cage. Edlebrock Performer heads and Victor Jr. EFI, FRPP 30lb injectors & Cartech fuel system. MSD ignition. Sothside Machine bars & Sub-frames, adj. upper's, 3.73's, Koni rear shocks, much more

08-11-2004, 02:21 PM	#5
89fast5oh Registered Member Join Date: Apr 2002 Location: Canada Posts: 56	88fivepointoh- All my car info is in my signature. Stang_ROTY- I havn't really played with my timing and if i did the track is 3hrs away. __________________ 351W .030", AFR 185s, Crane roller cam-.543" 220 -.562" 228@.050, TFS 351W EFI intake, Billet Roller Rockers, BBK Long Tubes, BBK X- Pipe, Dynomax Race Magnums w/dumps, 30lb injectors, 190lph intank pump, Holley Adjustable FPR, 75mm TB&MA, Underdrive pulleys, Aluminum Rad, Billet Flywheel, McCloud Clutch, World Class T-5, B&M Ripper Shifter 4.10s, McCreary G-60s, Lakewood 90/10s, Comp. Enginering 3 way adjust/rear, Upper and Lower Control arms, Autometer gauges.

08-11-2004, 02:27 PM	#6
89fast5oh Registered Member Join Date: Apr 2002 Location: Canada Posts: 56	My clutch is fine from what i can tell and traction is ok. Not the greatest in first, i have to feather it, but just a slight spin into second and away it goes. it doesn't feel like it gives much up top end, but i have always wondered and asked about the stock valve springs that came on older AFR heads. They say there good for .550" lift and i'm right on that, maybe a tinnie bit over, but i don't have coil bind. I've never measured the spring pressure to see if they are good enough tho. __________________ 351W .030", AFR 185s, Crane roller cam-.543" 220 -.562" 228@.050, TFS 351W EFI intake, Billet Roller Rockers, BBK Long Tubes, BBK X- Pipe, Dynomax Race Magnums w/dumps, 30lb injectors, 190lph intank pump, Holley Adjustable FPR, 75mm TB&MA, Underdrive pulleys, Aluminum Rad, Billet Flywheel, McCloud Clutch, World Class T-5, B&M Ripper Shifter 4.10s, McCreary G-60s, Lakewood 90/10s, Comp. Enginering 3 way adjust/rear, Upper and Lower Control arms, Autometer gauges.

08-11-2004, 02:28 PM	#7
Stang_ROTY Registered Member Join Date: Feb 2001 Location: Berkshire County - Massachusetts Posts: 735	We have damn near the same setup but I run a C4 and you run the 5 speed. Looks like the 5 speed is better for MPH and the C4 has a more consistent ET...which isn't surprising. No chip? Mine won't hold an idle without a chip. A 12 second street car is not shabby at all. __________________ Red 1993 GT Street Machine Best E.T. - 12.41/Best MPH = 108 Engine is a 1969 351 block w/393 stroker kit. Dynamic Roller Myte C4, 8 pt cage. Edlebrock Performer heads and Victor Jr. EFI, FRPP 30lb injectors & Cartech fuel system. MSD ignition. Sothside Machine bars & Sub-frames, adj. upper's, 3.73's, Koni rear shocks, much more

08-11-2004, 02:19 PM	#2
88fivepointoh Registered Member Join Date: Aug 2002 Location: Rochester Posts: 553	um yeah it should be... so its a 351 EFI setup? what injectors, computer, etc.. what gear ratio, intake etc.. give us some specs on your car then I can make a better assessment.

08-11-2004, 02:33 PM	#8
89fast5oh Registered Member Join Date: Apr 2002 Location: Canada Posts: 56	The car runs great, starts up and idles fine everytime. Well maybe 7 out of 10 times anyways. No chip, just the stock AL9 computer. Although it has developed a bit of a off-ilde stummble lately, i wonder if that has anything to do with it? __________________ 351W .030", AFR 185s, Crane roller cam-.543" 220 -.562" 228@.050, TFS 351W EFI intake, Billet Roller Rockers, BBK Long Tubes, BBK X- Pipe, Dynomax Race Magnums w/dumps, 30lb injectors, 190lph intank pump, Holley Adjustable FPR, 75mm TB&MA, Underdrive pulleys, Aluminum Rad, Billet Flywheel, McCloud Clutch, World Class T-5, B&M Ripper Shifter 4.10s, McCreary G-60s, Lakewood 90/10s, Comp. Enginering 3 way adjust/rear, Upper and Lower Control arms, Autometer gauges.

08-11-2004, 02:40 PM	#9
88fivepointoh Registered Member Join Date: Aug 2002 Location: Rochester Posts: 553	I would start with an increase of fuel pressure to 45 maybe higher, the track will tell the tale. Then timing and ignition could use to be looked at. what your tune up like? What plugs are you using? Are you running and MSD box, there known for High end cut off issues.. Mine did that.. took me forever to figure it out.

08-11-2004, 03:45 PM	#10
~The Jester~ Rat Killer Join Date: Aug 2002 Location: Cold ass Ohio Posts: 1,143	You've got some minor issues. 114 MPH should be at least a 12.20 or so. That means she's making the ponies, but the et is falling off somewhere. Usually the little end of the track, if you're spinning in second you've got traction problems. Run a little less air pressure, get some pointers on "tuning" your upper control arms, and play with the timing. There's is literally TONS of torque hiding in your distributor! I'd be willing to bet your stocker distributor isn't bringing yout total timing in until about 4500 which is waaaaay late, and it's probably only giving you about 30@ total which also sucks. Timing is a "black art" of sorts, and sometimes pricey but it the long run it pays you back 100%. Start with the little stuff and work your way up. Maybe get some cold air in that motor too. And by the way, a 12 second street car is NOTHING to sneeze at!!!! __________________ d-Con Racing "Nothing fancy, just 347 inches of RAT POISON!" MICE need not apply.....

08-11-2004, 03:55 PM	#11
88fivepointoh Registered Member Join Date: Aug 2002 Location: Rochester Posts: 553	Are you running a stock distributor? If so maybe upgrade to a MSD or something..

08-11-2004, 04:09 PM	#12
Capri306 Moderator Join Date: Sep 1998 Location: Grand Rapids, Michigan, USA Posts: 1,001	Read your spark plugs. Have you actually checked for coil bind? Get a custom chip or a twEECer. __________________ Capri306, Moderator The Mustang Works Online 1979 Mercury Capri 1987 5.0L Mustang LX Notchback 1993 5.8L Eddie Bauer Bronco

08-11-2004, 05:10 PM	#13
Dark_5.0 Registered Member Join Date: Apr 2001 Location: Staging lane Posts: 4,337	114mph seems about right. What was your 60ft, I am guessing that it sucked. A high 11 or low 12 should be easy with 114mph. Were you running slicks? __________________ 92' LX-Big brakes, Lots and lots of suspension, GT40X heads, Ported cobra intake, stock cam, Vortech SC trim. 00' Lightning-Stock 88'CRX-13 second ego killer

08-11-2004, 09:26 PM	#14
88workcar Registered Member Join Date: Oct 1999 Location: Pierre Part, La. U.S.A. Posts: 1,850	89fast, you DO NOT have motor issues. TRACTION, 60FT, WHEELIES get it. You must work on these or you will never get a good ET. 114 is 11 sec car. As much time, effort, and money that you spent on motor, needs to be spent on the CAR. Start with a set of 90/10s. __________________ 88workcar 1988 Mustang LX 342. 417rwhp @ 6800. 28 X 10 ET Drag, 4.30s, 10.69 @ 126.43 1.42 60ft. 11.13 @ 127.7 on BFGs 1.72 60ft Rice Hater # 42 To be old and wise, You must first be young and stupid I'm somewhere in tthe middle.

08-11-2004, 11:17 PM	#15
89fast5oh Registered Member Join Date: Apr 2002 Location: Canada Posts: 56	Hey guys, thanks for all the suggestions and input. I'll have to play around with timing, fuel press and see what i can do about the traction. I made the runs on my McCreary G-60s if any of you are familiar with those ones. The car is a daily driver and it is really fun to drive and hard to beat might i add. A side note that may shed some light on the matter that i just remembered, was that a couple months ago i raced a guy in a old dodge duster out on the hiway and beat on him pretty good. He claimed he went 12.20 on slicks last season and has made no changes. We raced from a stop and i beat him, and raced again from a roll and i beat him again. I even noticed that i pulled away and kept slightly pulling from him the whole time we raced. Its just to me it always seemed like i got pretty good traction, i would like to feel the car on slicks launching at 5500rpm, hahaha __________________ 351W .030", AFR 185s, Crane roller cam-.543" 220 -.562" 228@.050, TFS 351W EFI intake, Billet Roller Rockers, BBK Long Tubes, BBK X- Pipe, Dynomax Race Magnums w/dumps, 30lb injectors, 190lph intank pump, Holley Adjustable FPR, 75mm TB&MA, Underdrive pulleys, Aluminum Rad, Billet Flywheel, McCloud Clutch, World Class T-5, B&M Ripper Shifter 4.10s, McCreary G-60s, Lakewood 90/10s, Comp. Enginering 3 way adjust/rear, Upper and Lower Control arms, Autometer gauges.

08-12-2004, 02:05 PM	#16
88fivepointoh Registered Member Join Date: Aug 2002 Location: Rochester Posts: 553	SMOKE THEM DODGES.. Play around with it at the track, I think with a better tire combination you'll get closer to what your looking for.

08-12-2004, 05:20 PM	#17
Stang_ROTY Registered Member Join Date: Feb 2001 Location: Berkshire County - Massachusetts Posts: 735	I need to make that type of power! My car is setup for ET, but I just need to find the power. What are you using for tires?? What pressure you run them at? __________________ Red 1993 GT Street Machine Best E.T. - 12.41/Best MPH = 108 Engine is a 1969 351 block w/393 stroker kit. Dynamic Roller Myte C4, 8 pt cage. Edlebrock Performer heads and Victor Jr. EFI, FRPP 30lb injectors & Cartech fuel system. MSD ignition. Sothside Machine bars & Sub-frames, adj. upper's, 3.73's, Koni rear shocks, much more

08-12-2004, 06:36 PM	#18
fiveOguy20 Registered Member Join Date: Sep 2002 Posts: 156	ya i must agree with everyone that 114 is 11's no doubt cuz im goin 11.90's at 113 so its in there! At this point its all bout traction an driving. good luck __________________ 347- ported X heads, Xcam , RPM air-gap intake, 650 holley DP, 10:5 comp., equal lenght shorties, pullies, MSD ignition, pro 5.0 shifter. stock fuel system !! best ET: 11.95 @113 1.64 60 foots

08-12-2004, 06:53 PM	#19
89fast5oh Registered Member Join Date: Apr 2002 Location: Canada Posts: 56	Stang_ROTY - I'm using McCreary American Racer G-60 tires. They are actually a Dirt Track tire but have a DOT # so i use them on the street, (not i need DOT tires where i'm from, cheesy cops). I run them at about 15psi, and they seem to work fairly well, but i guess not good enough for what i want. __________________ 351W .030", AFR 185s, Crane roller cam-.543" 220 -.562" 228@.050, TFS 351W EFI intake, Billet Roller Rockers, BBK Long Tubes, BBK X- Pipe, Dynomax Race Magnums w/dumps, 30lb injectors, 190lph intank pump, Holley Adjustable FPR, 75mm TB&MA, Underdrive pulleys, Aluminum Rad, Billet Flywheel, McCloud Clutch, World Class T-5, B&M Ripper Shifter 4.10s, McCreary G-60s, Lakewood 90/10s, Comp. Enginering 3 way adjust/rear, Upper and Lower Control arms, Autometer gauges.

08-12-2004, 09:55 PM	#20
68Falcon Bracket Racer Join Date: Apr 2003 Location: Loxahatchee, Florida Posts: 210	My best is 11.58@115 __________________ Streetcar 90 Notch 69 351W .030 over. Untouched 69 351 heads Crane cams duration @050 216in 228ex. valve lift .484in .512ex. Untouched RPM air gap intake with Holley 750 DP. Hooker headers. C6 trans. 8.8 with 3.73, Strange 31spline alxes and spool Racecar 68 Falcon 10 point Cage and FE487ci 13.6:1 compression. .740 lift 276in 284ex duration @.050 in the Works. 428CJ heads. Port O Sonic intake with 1050 Dominator. PowerGlide trans.

Thread Tools
Show Printable Version Email this Page
Display Modes	Rate This Thread
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode	Rate This Thread:

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Great Joke!.....Especially if you are from Michigan	MTU 50	Blue Oval Lounge	10	12-12-2002 03:05 PM
Just got a great 90' LX...now to make it faster...?	Suave	Windsor Power	12	07-06-2001 02:13 PM
2 Great runs with a couple friendly 5.0s	EZRIDN	Stang Stories	5	03-12-2001 12:02 AM