situation on my T-5...

90dpscoupe · 07-11-2001, 08:27 PM

Talked to a guy that knows his stuff, he said i can save 250$ if i pull the trans myself, plus he told me the sound im hearing is a "cluster" and possibly, most likely a bad "bearing", also said he will do a bench job and let me watch him do the whole job

and he said it wont be to expensive, considering thats all it might need, i have faith in this guy. thnx for the help guys, and hope you other guys sharing my frustration get things squared away.

------------------
90 lx coupe: 175k miles, steeda water pump pully, hurst shifter, Mac cold air fenderwell, accel supercoil, ADS chip, aluminum D/S, Black magic fan, 3.27grs.
Best time: 13.9116(on 225/60/15 firehawks)
Best mph: 98.17
Best 60': 1.9607

next mods: subframes, mac h-pipe

Rick 91GT · 07-11-2001, 09:28 PM

If it is the cluster, you are looking at $250 for a new one, and you should replace the imput shaft since it rides on top of the cluster another $100, and the master rebuild kit runs around $150. That is what went out on mine, except my imput shaft only had 3 teeth left and the bottom cluster gear that meshed with it didn't even look like a gear anymore..I'll see if I cna take some pic's and post them.

Good Luck

------------------
Check Out My Site 91GT,Holley SysteMAX II Kit-Heads 2.02" x 1.60" port matched to a 1262,Anderson N-61,24#,76mm C&L,Full MAC exhaust 1-5/8" Long tubes,2-1/2" O.R H-Pipe,2 1/2" cat back, No A/C or PS or emissions, 12" K&N Filter,RNH PERFORMANCE Ram Air,Ron Davis Radiator,Full Suspension,S&W 8pt "X" brace,JAZ seats,3:73's,Welds..etc,4:30's and 31 splines coming very soon! FIRST TIME OUT 12.16@111 WHEELS-UP

90dpscoupe · 07-11-2001, 10:51 PM

What ecxactly does that master rebuild kit contain? bearings? i told the guy i only wanted necesary parts, cuz im on a budget

he did mention the price for the cluster, but i think i can get a good rebuild out of it for under 400 i hope.
since im pulling it myself i should go ahead and try rebuilding it....naw:8 maybe i better not.

Rick 91GT · 07-12-2001, 07:35 AM

The master rebuild kits do come with all the bearings, snycros, sliders, pads for the forks, and all the other little parts for the rebuild.

07-11-2001, 08:27 PM	#1
90dpscoupe Registered Member Join Date: Jun 2000 Location: sanantonio, Tx, usa Posts: 1,407	situation on my T-5... Talked to a guy that knows his stuff, he said i can save 250$ if i pull the trans myself, plus he told me the sound im hearing is a "cluster" and possibly, most likely a bad "bearing", also said he will do a bench job and let me watch him do the whole job and he said it wont be to expensive, considering thats all it might need, i have faith in this guy. thnx for the help guys, and hope you other guys sharing my frustration get things squared away. ------------------ 90 lx coupe: 175k miles, steeda water pump pully, hurst shifter, Mac cold air fenderwell, accel supercoil, ADS chip, aluminum D/S, Black magic fan, 3.27grs. Best time: 13.9116(on 225/60/15 firehawks) Best mph: 98.17 Best 60': 1.9607 next mods: subframes, mac h-pipe

Thread Tools
Show Printable Version Email this Page
Display Modes	Rate This Thread
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode	Rate This Thread:

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
The World Has Had Enough Warning, dealing with current war situation, may offend	Fox Body	Blue Oval Lounge	11	04-10-2003 05:25 PM
A strange situation	fordkid68	Classic Mustangs	8	09-24-2002 09:22 PM
Can somebody tell me who I can contact about my situation?	silverv6	Blue Oval Lounge	15	01-13-2002 11:58 PM
Is it worth adding more timing in my situation???	Blaster	Windsor Power	1	07-06-2001 02:45 PM

07-11-2001, 09:28 PM	#2
Rick 91GT Procharged! Join Date: May 1999 Location: Hanover, PA Posts: 1,539	If it is the cluster, you are looking at $250 for a new one, and you should replace the imput shaft since it rides on top of the cluster another $100, and the master rebuild kit runs around $150. That is what went out on mine, except my imput shaft only had 3 teeth left and the bottom cluster gear that meshed with it didn't even look like a gear anymore..I'll see if I cna take some pic's and post them. Good Luck ------------------ Check Out My Site 91GT,Holley SysteMAX II Kit-Heads 2.02" x 1.60" port matched to a 1262,Anderson N-61,24#,76mm C&L,Full MAC exhaust 1-5/8" Long tubes,2-1/2" O.R H-Pipe,2 1/2" cat back, No A/C or PS or emissions, 12" K&N Filter,RNH PERFORMANCE Ram Air,Ron Davis Radiator,Full Suspension,S&W 8pt "X" brace,JAZ seats,3:73's,Welds..etc,4:30's and 31 splines coming very soon! FIRST TIME OUT 12.16@111 WHEELS-UP

07-11-2001, 10:51 PM	#3
90dpscoupe Registered Member Join Date: Jun 2000 Location: sanantonio, Tx, usa Posts: 1,407	What ecxactly does that master rebuild kit contain? bearings? i told the guy i only wanted necesary parts, cuz im on a budget he did mention the price for the cluster, but i think i can get a good rebuild out of it for under 400 i hope. since im pulling it myself i should go ahead and try rebuilding it....naw:8 maybe i better not.

07-12-2001, 07:35 AM	#4
Rick 91GT Procharged! Join Date: May 1999 Location: Hanover, PA Posts: 1,539	The master rebuild kits do come with all the bearings, snycros, sliders, pads for the forks, and all the other little parts for the rebuild.