mustang belt ?????????

HAITHAM · 08-06-2001, 11:34 PM

Can I use a belt with 7 lanes(the inner face of the belt divided into 7 lines).

*normally mustang belts coming with 6 lanes.

------------------
94 COBRA # 926/5009
TFS track heat heads (ported), Cobra intake (ported), 24# Injectors, 3/8" Phenolic spacer, E303 Cam, TFS 1.7 rr
BBK 1 5/8" headers, BBK 65mm TB, Pro-M 80mm MAS, PIH kit w/ A9L computer, FMS 3.55 ratio
BBK 190 lph fuel pump, Paxton fpr, MSD'S, March Pulley's, Pro-5 tower power shifter, Autometer shift light (5600),
Intellitronix Air/Fuel gauge, Eibach Sportline Springs, Tokico 5-way adjustable, Granatelli Motorsport Subframe

91evilstang · 08-06-2001, 11:53 PM

Ihave heard of guys using blowers like kenny bell that use the same belt as the accesories up gradeing to a 10 rib belt but it requires custom pullys and is expensive.do you have a belt slipping problem now?If so mabie you should get a new tensioner auto zone has them.or mabie just a shorter belt.just suggestions.

------------------
91GT Flowmaster 2 chambers,off road H pipe,mac equalength headers,F303 cam,high lift valve springs ,svo 1.6 roller rockers,19*timing,410's,BBK cold air kit,hurst shifter, Pullys,World class T5 MSD 6al box. Ran 13.5@101 with stock headers and air box.

HAITHAM · 08-07-2001, 12:06 AM

Actually I didn't found the size of the belt with 6-rib, so I went to the 7-rib, can I trim 1-rib ??????

08-06-2001, 11:34 PM	#1
HAITHAM Registered Member Join Date: Jun 2000 Location: Saudi Arabia Posts: 130	mustang belt ????????? Can I use a belt with 7 lanes(the inner face of the belt divided into 7 lines). *normally mustang belts coming with 6 lanes. ------------------ 94 COBRA # 926/5009 TFS track heat heads (ported), Cobra intake (ported), 24# Injectors, 3/8" Phenolic spacer, E303 Cam, TFS 1.7 rr BBK 1 5/8" headers, BBK 65mm TB, Pro-M 80mm MAS, PIH kit w/ A9L computer, FMS 3.55 ratio BBK 190 lph fuel pump, Paxton fpr, MSD'S, March Pulley's, Pro-5 tower power shifter, Autometer shift light (5600), Intellitronix Air/Fuel gauge, Eibach Sportline Springs, Tokico 5-way adjustable, Granatelli Motorsport Subframe

Thread Tools
Show Printable Version Email this Page
Display Modes	Rate This Thread
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode	Rate This Thread:

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Safety Issue 64 - 70 Mustangs	Mach1 Cobra Jet	Classic Mustangs	20	07-11-2005 08:06 PM
Yellow Mustang Stampede TULSA OK August 17	stylin99	Ford Show & Go	2	11-09-2004 11:19 PM
351W belt routing	Ieatcamaros	Windsor Power	1	05-02-2003 08:15 PM
t-5, is it the same in the 4 cylinder and V8	ex-lt1-guy	Windsor Power	12	03-03-2002 01:59 AM
New Mustang	Mustang[RIP]	Classic Mustangs	2	10-17-2001 01:50 AM

08-06-2001, 11:53 PM	#2
91evilstang Registered Member Join Date: Mar 2001 Location: lafayette IN USA Posts: 48	Ihave heard of guys using blowers like kenny bell that use the same belt as the accesories up gradeing to a 10 rib belt but it requires custom pullys and is expensive.do you have a belt slipping problem now?If so mabie you should get a new tensioner auto zone has them.or mabie just a shorter belt.just suggestions. ------------------ 91GT Flowmaster 2 chambers,off road H pipe,mac equalength headers,F303 cam,high lift valve springs ,svo 1.6 roller rockers,19*timing,410's,BBK cold air kit,hurst shifter, Pullys,World class T5 MSD 6al box. Ran 13.5@101 with stock headers and air box.

08-07-2001, 12:06 AM	#3
HAITHAM Registered Member Join Date: Jun 2000 Location: Saudi Arabia Posts: 130	Actually I didn't found the size of the belt with 6-rib, so I went to the 7-rib, can I trim 1-rib ??????