need major tourque out of a 302!(non efi)

LX XLR8R · 01-31-2001, 10:07 AM

hey guys..i just aquired a '80 full size bronco with a 302 in it..i also can get a fresh '87 roller motor for free(block and heads)..i also have a e-303 and a b-303 laying around with some gt-40 heads that need 7 new valves(but thats no big deal)..basically i want to keep it carbed but do a roller motor..i was thinking mill and polish the gt-40 heads and use the b-303..what intake and carb should i get..i was thinking the regular performer intake with a 600cfm carb..i am setting up my power to be from idle to about 5,000rpms..
this truck will be riding on 38" tires with probally about 4.56 gears and a 9"-12" over all lift..thanks for all the help guys

------------------
1987 black notch(ex 4 banger)
DSS 306 w/ main support...Elderbrock 6028 heads..gt-40 intake..24# injectors...70 mm tb..77 pro-m...accel 300+..mac full legnth..tremec w/ pro5oh...full MAC exhaust,off road h-pipe,long tubes, catback...ron davis radiator..subframes, control arms...CFDF II..o yea holley FPR sucks..dont buy one..

LX XLR8R · 01-31-2001, 11:49 AM

ok another question..the fuel pump will work no prblem as long as i change the timing chain cover right??

------------------
1987 black notch(ex 4 banger)
DSS 306 w/ main support...Elderbrock 6028 heads..gt-40 intake..24# injectors...70 mm tb..77 pro-m...accel 300+..mac full legnth..tremec w/ pro5oh...full MAC exhaust,off road h-pipe,long tubes, catback...ron davis radiator..subframes, control arms...CFDF II..o yea holley FPR sucks..dont buy one..

spinemup · 01-31-2001, 11:51 AM

your gonna need a different distributer i think

LX XLR8R · 01-31-2001, 12:06 PM

hmmm..i think i just need a rollor motor gear on the older distributer..good question

------------------
1987 black notch(ex 4 banger)
DSS 306 w/ main support...Elderbrock 6028 heads..gt-40 intake..24# injectors...70 mm tb..77 pro-m...accel 300+..mac full legnth..tremec w/ pro5oh...full MAC exhaust,off road h-pipe,long tubes, catback...ron davis radiator..subframes, control arms...CFDF II..o yea holley FPR sucks..dont buy one..

spinemup · 01-31-2001, 12:57 PM

im pretty sure the roller and non roller motors have different firing orders

FoxBuilder · 01-31-2001, 01:13 PM

LX,
Your going in the right direction. You will need a hardened gear for the distributor to work with the roller cam. Should be able to use the timing cover and fuel assembly, I would recommend a new fuel pump (Edelbrock). Milling the heads is a good I idea, I would try to bring the compression up to at least 10:1. The performer intake with a 600 carb should work well with the B303, would probably also use a single bore 1/2" spacer to help with some top end power. The 38" tires are going to look good but are going to kill low end torque. You'll have to whine that B303 up to get a good launch, even then it might bog.

IRACERICE · 01-31-2001, 01:30 PM

Hey LX,

Why don't you finish your car first. Dec 28 has come and gone and your car is still sitting where it was..... LOL

------------------
93 del sol 12.14 @ 115.8 (retired)
on order: 2001 White S2000
still have: 91 crx 12.46 @ 108.5 mph

LX XLR8R · 01-31-2001, 04:33 PM

hey iracerice..dont be a di<k

i would be running 4.56 gears in it so that should help to turn those monsters

------------------
1987 black notch(ex 4 banger)
DSS 306 w/ main support...Elderbrock 6028 heads..gt-40 intake..24# injectors...70 mm tb..77 pro-m...accel 300+..mac full legnth..tremec w/ pro5oh...full MAC exhaust,off road h-pipe,long tubes, catback...ron davis radiator..subframes, control arms...CFDF II..o yea holley FPR sucks..dont buy one..

Skyman · 02-01-2001, 12:35 AM

I would use the E-303 it makes more low end torque than the B cam IMHO.

Skyler

------------------
-1989 Saleen Mustang #406-
TFS Heads, Edelbrock intake, E-303, 3.73's, 1 5/8 shortys, Offroad-H, 2chamber flows, 36psi FPR, 15degrees timing, 70mm tb, 73mm maf, 24lb inj, Crank pulley, MSD6A, Alum driveshaft.

Added: B&M Ripper, Subframes, & Turndowns.

FoxBuilder · 02-01-2001, 07:26 AM

LX,
The firing order out of the '80 is probably 1-5..., and the B303/E303 is 1-3... Always use the firing order that comes with the cam, Ford might have changed firing orders but they did not change cranks. What transmission does the truck have in it? A tranny with a lower ratio first would do good. You'll be loosing some torque from the pinion angle. If the E303 provides more low end torque I would go with Skyman's recommendation, but I would in that case step up to the Performer RPM intake. Witch ever way you go I think you'll enjoy the Truck, defiantly be noticeable!

Five0 · 02-01-2001, 08:38 AM

I would think those cams would be too much for what he wants to do because they are more for a high revving engine. I think you will be better suited to try to sell those cams to try to get enough money to get you a cam more for low-end torque. I would call comp cams and tell them what you are going to do with it and see what they recommend.

Just my .02

------------------
James Cox
nochevy@hotmail.com
1991 Mustang LX
12.565 @109.38mph 1.764 60ft

LX XLR8R · 02-01-2001, 12:06 PM

five-o..i would love to get a new one but this project is on a budget..i will be running at least 4.56 gearing and the bronco does have a 4low..
would i be better of using a stock HO cam or should i run the e-303 a few degrees advanced??

------------------
1987 black notch(ex 4 banger)
DSS 306 w/ main support...Elderbrock 6028 heads..gt-40 intake..24# injectors...70 mm tb..77 pro-m...accel 300+..mac full legnth..tremec w/ pro5oh...full MAC exhaust,off road h-pipe,long tubes, catback...ron davis radiator..subframes, control arms...CFDF II..o yea holley FPR sucks..dont buy one..

01-31-2001, 10:07 AM	#1
LX XLR8R Dirk Diggler Join Date: Feb 1999 Location: SLOATSBURG, NY Posts: 1,931	need major tourque out of a 302!(non efi) hey guys..i just aquired a '80 full size bronco with a 302 in it..i also can get a fresh '87 roller motor for free(block and heads)..i also have a e-303 and a b-303 laying around with some gt-40 heads that need 7 new valves(but thats no big deal)..basically i want to keep it carbed but do a roller motor..i was thinking mill and polish the gt-40 heads and use the b-303..what intake and carb should i get..i was thinking the regular performer intake with a 600cfm carb..i am setting up my power to be from idle to about 5,000rpms.. this truck will be riding on 38" tires with probally about 4.56 gears and a 9"-12" over all lift..thanks for all the help guys ------------------ 1987 black notch(ex 4 banger) DSS 306 w/ main support...Elderbrock 6028 heads..gt-40 intake..24# injectors...70 mm tb..77 pro-m...accel 300+..mac full legnth..tremec w/ pro5oh...full MAC exhaust,off road h-pipe,long tubes, catback...ron davis radiator..subframes, control arms...CFDF II..o yea holley FPR sucks..dont buy one..

Thread Tools
Show Printable Version Email this Page
Display Modes	Rate This Thread
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode	Rate This Thread:

01-31-2001, 11:49 AM	#2
LX XLR8R Dirk Diggler Join Date: Feb 1999 Location: SLOATSBURG, NY Posts: 1,931	ok another question..the fuel pump will work no prblem as long as i change the timing chain cover right?? ------------------ 1987 black notch(ex 4 banger) DSS 306 w/ main support...Elderbrock 6028 heads..gt-40 intake..24# injectors...70 mm tb..77 pro-m...accel 300+..mac full legnth..tremec w/ pro5oh...full MAC exhaust,off road h-pipe,long tubes, catback...ron davis radiator..subframes, control arms...CFDF II..o yea holley FPR sucks..dont buy one..

01-31-2001, 11:51 AM	#3
spinemup Registered Member Join Date: May 2000 Location: middleboro,ma, usa Posts: 734	your gonna need a different distributer i think

01-31-2001, 12:06 PM	#4
LX XLR8R Dirk Diggler Join Date: Feb 1999 Location: SLOATSBURG, NY Posts: 1,931	hmmm..i think i just need a rollor motor gear on the older distributer..good question ------------------ 1987 black notch(ex 4 banger) DSS 306 w/ main support...Elderbrock 6028 heads..gt-40 intake..24# injectors...70 mm tb..77 pro-m...accel 300+..mac full legnth..tremec w/ pro5oh...full MAC exhaust,off road h-pipe,long tubes, catback...ron davis radiator..subframes, control arms...CFDF II..o yea holley FPR sucks..dont buy one..

01-31-2001, 12:57 PM	#5
spinemup Registered Member Join Date: May 2000 Location: middleboro,ma, usa Posts: 734	im pretty sure the roller and non roller motors have different firing orders

01-31-2001, 01:13 PM	#6
FoxBuilder Registered Member Join Date: Sep 1999 Location: Columbus, Ohio Posts: 233	LX, Your going in the right direction. You will need a hardened gear for the distributor to work with the roller cam. Should be able to use the timing cover and fuel assembly, I would recommend a new fuel pump (Edelbrock). Milling the heads is a good I idea, I would try to bring the compression up to at least 10:1. The performer intake with a 600 carb should work well with the B303, would probably also use a single bore 1/2" spacer to help with some top end power. The 38" tires are going to look good but are going to kill low end torque. You'll have to whine that B303 up to get a good launch, even then it might bog.

01-31-2001, 01:30 PM	#7
IRACERICE Registered Member Join Date: Jul 2000 Location: New York Posts: 58	Hey LX, Why don't you finish your car first. Dec 28 has come and gone and your car is still sitting where it was..... LOL ------------------ 93 del sol 12.14 @ 115.8 (retired) on order: 2001 White S2000 still have: 91 crx 12.46 @ 108.5 mph

01-31-2001, 04:33 PM	#8
LX XLR8R Dirk Diggler Join Date: Feb 1999 Location: SLOATSBURG, NY Posts: 1,931	hey iracerice..dont be a di<k i would be running 4.56 gears in it so that should help to turn those monsters ------------------ 1987 black notch(ex 4 banger) DSS 306 w/ main support...Elderbrock 6028 heads..gt-40 intake..24# injectors...70 mm tb..77 pro-m...accel 300+..mac full legnth..tremec w/ pro5oh...full MAC exhaust,off road h-pipe,long tubes, catback...ron davis radiator..subframes, control arms...CFDF II..o yea holley FPR sucks..dont buy one..

02-01-2001, 12:35 AM	#9
Skyman I need 110mph Trap Speed! Join Date: Feb 1999 Location: So, CA Posts: 4,315	I would use the E-303 it makes more low end torque than the B cam IMHO. Skyler ------------------ -1989 Saleen Mustang #406- TFS Heads, Edelbrock intake, E-303, 3.73's, 1 5/8 shortys, Offroad-H, 2chamber flows, 36psi FPR, 15degrees timing, 70mm tb, 73mm maf, 24lb inj, Crank pulley, MSD6A, Alum driveshaft. Added: B&M Ripper, Subframes, & Turndowns.

02-01-2001, 07:26 AM	#10
FoxBuilder Registered Member Join Date: Sep 1999 Location: Columbus, Ohio Posts: 233	LX, The firing order out of the '80 is probably 1-5..., and the B303/E303 is 1-3... Always use the firing order that comes with the cam, Ford might have changed firing orders but they did not change cranks. What transmission does the truck have in it? A tranny with a lower ratio first would do good. You'll be loosing some torque from the pinion angle. If the E303 provides more low end torque I would go with Skyman's recommendation, but I would in that case step up to the Performer RPM intake. Witch ever way you go I think you'll enjoy the Truck, defiantly be noticeable!

02-01-2001, 08:38 AM	#11
Five0 Registered Member Join Date: Apr 2000 Location: middleburg, fl, usa Posts: 1,134	I would think those cams would be too much for what he wants to do because they are more for a high revving engine. I think you will be better suited to try to sell those cams to try to get enough money to get you a cam more for low-end torque. I would call comp cams and tell them what you are going to do with it and see what they recommend. Just my .02 ------------------ James Cox nochevy@hotmail.com 1991 Mustang LX 12.565 @109.38mph 1.764 60ft

02-01-2001, 12:06 PM	#12
LX XLR8R Dirk Diggler Join Date: Feb 1999 Location: SLOATSBURG, NY Posts: 1,931	five-o..i would love to get a new one but this project is on a budget..i will be running at least 4.56 gearing and the bronco does have a 4low.. would i be better of using a stock HO cam or should i run the e-303 a few degrees advanced?? ------------------ 1987 black notch(ex 4 banger) DSS 306 w/ main support...Elderbrock 6028 heads..gt-40 intake..24# injectors...70 mm tb..77 pro-m...accel 300+..mac full legnth..tremec w/ pro5oh...full MAC exhaust,off road h-pipe,long tubes, catback...ron davis radiator..subframes, control arms...CFDF II..o yea holley FPR sucks..dont buy one..