Line-lock installation

Chris_H · 02-09-2001, 01:20 AM

Ok guys I have had a line lock laying around tehhouse for over a week now and am finally getting this weekend off. How hard is it to put one in? I have NEVER messed with brakes before, let alone run brake lines and everything else for this installation. The instructions don't seem all that straightforward and wondered if you have any helpful hints. I am almost thinking its safer for me to take it to my mechanic so I don't kill myself by doing it wrong. Any help is greatly appreciated.

Chris

RobertD · 02-09-2001, 01:07 PM

Aha! So your going to tackle it yourself, huh? Be careful. Just be sure that all brake lines are not kinked and you aren't leaking anywhere. Good luck!

------------------
Robert
91GT; 88 ASC McLaren #709

Chris_H · 02-10-2001, 02:27 AM

You have any other ideas than be careful!? I don't like the idea that I could end up killing myself if I do this wrong! ANybody ever put one in, or should I just take it to my mechanic? Doesn't look all that easy.

Chris

Jeff Chambers · 02-10-2001, 07:15 AM

Its not really that hard. The worst part of the whole job is just trying to find a place to locate the cylinder. I put mine on the driver's side shock tower just above and forward of the master cylinder. This seemed to minimize the lengths of brake line I needed to fit and bend. The master cylinder uses ISO bubble flare fittings while the line-lok and proportioning valve use SAE double flares. It takes a while and more than a few trips to the parts store to get all of the right fittings. Take a look at my website for a plumbing schematic and parts list. One thing that I forgot in the schematic is the inverted flare adapters for the line-lock selenoid. You have to use an inverted flare adapter in the LL ports before you attach the tubing.

------------------
Jeff Chambers
Trophy Stock #3
11.97 Seconds / 114.5 MPH
Chambers Racing Team

Chris_H · 02-10-2001, 04:05 PM

Thanx for the reply and the tech article Jeff. From the looks of it it shouldn't be too hard, but I don't have most of the tools needed to do most of this and trying to get the wife to buy into the fact that I NEED them rather than want them would be harder than putting this in. I'll just let my mechanic deal with it and hope that he can have it done in the one day if he doesn't get too busy. Once again I appreciate the help.

Chris

02-09-2001, 01:20 AM	#1
Chris_H Registered Member Join Date: Oct 1999 Location: New Mexico Posts: 488	Line-lock installation Ok guys I have had a line lock laying around tehhouse for over a week now and am finally getting this weekend off. How hard is it to put one in? I have NEVER messed with brakes before, let alone run brake lines and everything else for this installation. The instructions don't seem all that straightforward and wondered if you have any helpful hints. I am almost thinking its safer for me to take it to my mechanic so I don't kill myself by doing it wrong. Any help is greatly appreciated. Chris

Thread Tools
Show Printable Version Email this Page
Display Modes	Rate This Thread
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode	Rate This Thread:

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Line Lock ?	Blownpony91	Windsor Power	2	10-07-2004 07:16 PM
Line Lock ?'s	GhOsT6_9	Windsor Power	1	03-19-2004 03:26 AM
Line Lock Help	RoadWarrior	Windsor Power	7	09-16-2002 06:34 AM
Line Lock Installation?	ciara	Windsor Power	2	07-16-2002 06:20 AM
Line lock question-which line goes to front brakes	Stang_ROTY	Windsor Power	1	05-20-2002 03:53 PM

02-09-2001, 01:07 PM	#2
RobertD Registered Member Join Date: Jun 1999 Location: El Paso, Texas, USA Posts: 170	Aha! So your going to tackle it yourself, huh? Be careful. Just be sure that all brake lines are not kinked and you aren't leaking anywhere. Good luck! ------------------ Robert 91GT; 88 ASC McLaren #709

02-10-2001, 02:27 AM	#3
Chris_H Registered Member Join Date: Oct 1999 Location: New Mexico Posts: 488	You have any other ideas than be careful!? I don't like the idea that I could end up killing myself if I do this wrong! ANybody ever put one in, or should I just take it to my mechanic? Doesn't look all that easy. Chris

02-10-2001, 07:15 AM	#4
Jeff Chambers Moderator Join Date: Aug 2000 Location: Milan, OH Posts: 2,699	Its not really that hard. The worst part of the whole job is just trying to find a place to locate the cylinder. I put mine on the driver's side shock tower just above and forward of the master cylinder. This seemed to minimize the lengths of brake line I needed to fit and bend. The master cylinder uses ISO bubble flare fittings while the line-lok and proportioning valve use SAE double flares. It takes a while and more than a few trips to the parts store to get all of the right fittings. Take a look at my website for a plumbing schematic and parts list. One thing that I forgot in the schematic is the inverted flare adapters for the line-lock selenoid. You have to use an inverted flare adapter in the LL ports before you attach the tubing. ------------------ Jeff Chambers Trophy Stock #3 11.97 Seconds / 114.5 MPH Chambers Racing Team

02-10-2001, 04:05 PM	#5
Chris_H Registered Member Join Date: Oct 1999 Location: New Mexico Posts: 488	Thanx for the reply and the tech article Jeff. From the looks of it it shouldn't be too hard, but I don't have most of the tools needed to do most of this and trying to get the wife to buy into the fact that I NEED them rather than want them would be harder than putting this in. I'll just let my mechanic deal with it and hope that he can have it done in the one day if he doesn't get too busy. Once again I appreciate the help. Chris