© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
08-24-2001, 08:13 PM | #1 |
Registered Member
Join Date: Aug 2000
Location: santa ana ca
Posts: 1,349
|
The mofo MOVES
Im sure most of you remember my post about racing my co-workers LS1 Z28 with 410's on the 8th for 50 bucks.
Well, He got it all dialed in and tuned up and took me for a run today. The mofo moves....its fukn quick. I figured that he would spin like hell when he hit second but he got some cpu deal that adjusts his shift softness and now it doesnt spin at all. I hope to god these TW heads and Holley intake drop over a second off of my time or Im gonna be in trouble ------------------ 95GT B303 cam, 1.7 rockers, 65mm TB, milled heads, 355's K&N, BBK Longtubes, Flowmaster cat back, pulleys, msd coil, 9mm wires, Tremec 3550, Pro5.0 shifter,10.5 Motorsport clutch, FMS aluminum driveshaft, weld in subframe connectors |
08-26-2001, 01:45 AM | #2 |
Registered Member
Join Date: Jun 2000
Location: sanantonio, Tx, usa
Posts: 1,407
|
lol, yea i heard all about those cpu tranny things, oh and did you get some ported tw heads? if not you should, i know its expensive, but good to have when your running against a car with mad topend, and more cubic inches.
my friend is getting stage 3's, but already runs 108 mph traps with ported stockers. no doubt those cars are fast. |
08-26-2001, 02:08 AM | #3 |
Registered Member
Join Date: Feb 2000
Posts: 469
|
Good luck man, those things are damn quick...seen more than a couple run 13.2 - 13.4 stock at the track... It's all about traction (you saw that at carlsbad) so make sure you can put the power to the ground!
-ed |
08-26-2001, 10:03 PM | #4 |
I need 110mph Trap Speed!
Join Date: Feb 1999
Location: So, CA
Posts: 4,315
|
Cut a 2.0 60' and get it tunned and you'll whoop him.
Skyler ------------------ -1989 Saleen Mustang #406- TFS TW Heads, E-303, Edelbrock intake, 70mm TB, 73mm MAF, 24lb injectors, 1 5/8 shorties, Off Road H, 3 Chamber flows, Jaz Race seats, Back seat removed, sub-frames, Roll Cage, and a 80 shot of N20. 12.54@107.4 Motor 332RWHP, 350rwtq |
08-27-2001, 12:22 AM | #5 |
Registered Member
Join Date: Aug 2000
Location: santa ana ca
Posts: 1,349
|
I think I went a little overboard before. Im going to need to gain over a half second not a full second to beat him. Its quick but I think its in the 13.5-13.4 area now. He hit a 13.8 stock. Im hoping to hit a 13 flat or better.
90dp, I didnt get them ported. I was going to but the guy at the shop that I bought the heads from said that I really wouldnt need it. He said that if I just port matched them to the intake they can support around 400hp. So I saved the money from porting the heads and got the more expensive Holley intake instead. ------------------ 95GT B303 cam, 1.7 rockers, 65mm TB, milled heads, 355's K&N, BBK Longtubes, Flowmaster cat back, pulleys, msd coil, 9mm wires, Tremec 3550, Pro5.0 shifter,10.5 Motorsport clutch, FMS aluminum driveshaft, weld in subframe connectors |
08-27-2001, 10:38 PM | #6 |
Registered Member
Join Date: Nov 2000
Location: So. Cal.
Posts: 244
|
Fastang,
I posted the following reply to your original thread. I think he may be faster than mid 13's. Here is my original post: OK, just want to give you some first hand info I have. One of my buds has a 00 Camaro SS with auto trans. He has the following mods: Eibach Lowering Springs - 1 1/2 inch drop LS1 Motorsports - Ram Air Lid K&N - Airfilter Hypertech Power Stat - 180 Degrees Hypertech Power Programmer - Programmed to the following.... Firmed Shift 75% Installed RFG Cooling Fan set for 180 Degree 1-2 Shift +2 2-3 Shift +2 Rev Limiter 6,300 he runs 13.2 all day long. His best time (at carlsbad) was 13.15 @ 106.57. Just lettin you know. Good luck and kick *** ! |
08-28-2001, 12:17 AM | #7 |
Registered Member
Join Date: Jun 2000
Location: sanantonio, Tx, usa
Posts: 1,407
|
Thats cool, the holley intake should be well worth the money, and if its port matched, your in good shape, man i bet your car would really love some 4.10's but i think i remember you saying about you liking to drive 80-90 on the highway without it screaming like me.
spank that guy...good luck. But any heads and cam 5.0 will give an f-bod a run for their money, modded or not. ------------------ 90 lx coupe: 5spd, 177k miles, steeda water pump pulley, Mac coldair fenderwell, Mac h-pipe, supercoil, ADS chip, 160 stat, aluminum D/S, Black magic fan, 3.27grs. Best time: 13.9116(on 225/60/15 firehawks) Best mph: 98.17 Best 60': 1.9607 next mods:4.10's, slicks. |
08-28-2001, 01:38 PM | #8 |
Guest
Posts: n/a
|
With the heads/intake and a good launch, I don't think you'll have that much of a problem w/ that guy.
------------------ '90 LX 5.0;12K original miles (no sh*&);3.55 gears; March pulleys;Edelbrock Performer Heads;BBK 1 5/8" equal length shorties;MSD 6AL ignition w/ blaster 2 coil;FMS E303 cam;Pro-M 75mm MAF;BBK 70mm TB; Eibach drag-launch spring kit;Southside welded subs;9" K&N cone filter charger;Hurst shifter;Cervini's 3" turbo hood;A/C delete; gutted cats;2 chamber Flomasters;Corbeau racing seats;FMS 30# injectors;JMS chip; Holley 190lb fp;TFS track heat Intake (12.299 @ 113 - 1.78 60') |
08-28-2001, 06:57 PM | #9 |
Registered Member
Join Date: Aug 2000
Location: santa ana ca
Posts: 1,349
|
I think I will be able to take him. If I get everything put on by the 8th I know Im not going to be able to get it dyno tuned by then though
gp0001, thanks for the input. I also have a friend with a quick SS. His is an M6 with just cutouts, MAF, and a lid and he's hitting 12.9 @ 110 on a 2.3 60ft But this guys car just isnt as fast. I've been in it and even at Pomona its best run was a 13.8. ------------------ 95GT B303 cam, 1.7 rockers, 65mm TB, milled heads, 355's K&N, BBK Longtubes, Flowmaster cat back, pulleys, msd coil, 9mm wires, Tremec 3550, Pro5.0 shifter,10.5 Motorsport clutch, FMS aluminum driveshaft, weld in subframe connectors |
08-29-2001, 08:39 AM | #10 |
or '331 LX Eric'
Join Date: Jan 1999
Location: Columbus, Ohio
Posts: 2,142
|
fastang - Those newer Z28's are just weird...let me elaborate. I have said this before (and will say it again here ), I have seen bone stock Z28's (00's) run consistent 14.0's all day (auto) and another run 13.4's (also an auto). You really don't know what you're getting with one of these cars. That's why it's always to fun to watch these cars at the track.
Another quick experience - a sligthly modded 00 Z28 with exhaust, LID, and a few other goodies I can't seem to remember, was going 12.9's @ 108 on drag radials with 1.9 & 2.0 60's. Regardless, have fun and good luck. I personally think with some good shifting and a decent 60' you will take him E |
08-31-2001, 03:18 PM | #11 |
Tubbed and Juiced
Join Date: Mar 2001
Location: Tulsa, Oklahoma
Posts: 1,861
|
With the heads and intake I see no problem in you getting some 12 second timeslips. I'm running my SS at the track tonight. I'm guessing 13.5's.
------------------ 1989 GT, 3:55's, full exhaust, 4 in. hood, Pro 5.0, Have many other parts 4 sale. All parts for sale now. 2000 Camaro SS-A4 =P 1989 Chevy S-10, EX. Cab-383(500+hp on motor), trick flow heads, trick flow pistons, etc... autometer phantom gauges, "built" 700R4, roll cage, lexan back window, corbeau seats, R.H.S. 5 harnesses, Fuel cell, convo pro wheels, 15x14's with 29x18.5 M/T'S on back, 15x4's on front, nitrous, and so much more! http://www.geocities.com/i8urvpr/JM.html |
08-31-2001, 03:36 PM | #12 |
or '331 LX Eric'
Join Date: Jan 1999
Location: Columbus, Ohio
Posts: 2,142
|
Good luck, 1BAD89, I'm curious to see your results.
Do you have any mods on the SS? E ------------------ 1991 5.0 LX Coupe - 38,000 miles 13.17 @ 106.14 mph w/ 2.138 60' |
09-01-2001, 08:37 PM | #13 |
Registered Member
Join Date: Aug 2000
Location: santa ana ca
Posts: 1,349
|
Yeah, 1BAD89, whadya run?
------------------ 95GT B303 cam, 1.7 rockers, 65mm TB, milled heads, 355's K&N, BBK Longtubes, Flowmaster cat back, pulleys, msd coil, 9mm wires, Tremec 3550, Pro5.0 shifter,10.5 Motorsport clutch, FMS aluminum driveshaft, weld in subframe connectors |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
How Much QA1 K member Moves Front tires forward | 87BOSS351C | Windsor Power | 1 | 02-04-2003 07:02 PM |
Modular Shootout moves venue to new location for 2003. | Moonlight96GT | Blue Oval Lounge | 0 | 08-01-2002 06:01 PM |
Got myself a new LIZARD! | Lizard King | Blue Oval Lounge | 13 | 03-28-2002 03:13 PM |