![SEARCH](http://www.mustangworks.com/images/search.png)
![The Mustang Works](http://www.mustangworks.com/images/mw_footer_logo.gif)
© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
![]() |
#1 |
Registered Member
Join Date: Aug 2000
Location: Wisconsin
Posts: 879
|
![]() well...installed my TFS intake and accufabe TB..started the car and had a bad vacum leak..found that and fixed it..put antifreeze back in..idled fine in the garage..then when i backed it out and hit the brakes they were stiff as hell...had to push as hard as i could to stop...then when i went down the block it suddenly started bucking then made a few odd noises and stalled???? WTF
my freind that helps me said he thinks we forgot a vaccum line and that, that vaccum line sucks oil to the top of the motor..and that when it stalled it ran out of oil on the top end and bent my push rods??? need some help bad!!! ------------------ '91 GT,91K,T-5,air silencer removed,racing clutch(previous owner put in so dont know what kind),K&N air filter,Mac long tubes,Cat-back,off road H,FMS 9mm wires,Competition gauges,C&L 76mm MAF Waiting install:TFS street heat,Accufab TB Future Mods:3.73's,Pro 5.0,TFS heads,TFS stage 1 cam,lakewood struts/shocks,nitto DR's ICQ#35670781 ![]() |
![]() |
![]() |
![]() |
#2 |
Registered Member
Join Date: Oct 1999
Location: Cincinnati, Ohio
Posts: 1,575
|
![]() Sounds like a vaccume like to me too. Check the big vac. line that comes off the firewall onthe drivers side. It's a a tree with a few others. As for bending the pushrods and running out of oil?? I don't think so. Oil doesn't flow threw the intake.
------------------ 87 GT, 4 inch cowl hood,17x9 Cobra R's/255/45's,GT-40 heads,Crane 2031, Edelbrock intake, long tubes headers,h-pipe,Flows,BBK cold air, Mass air,70mm MAF, 1.7's, 1" spacer,underdrive pulleys,Pro 5.0, King Cobra, Adj. fuel Reg., Lakewood Lift Bars,50/50's,subframes, 4.10's. Best time 12.759 Best MPH 106.79 Best 60' 1.695 Visit my site at: http://www.geocities.com/cobrar93_2000/MyPage.html |
![]() |
![]() |
![]() |
#3 |
Registered Member
Join Date: Aug 2000
Location: Wisconsin
Posts: 879
|
![]() also..when it started bucking and jerking it was like it was being starved for either gas or air..and once it stalled some smoked was coming out from the hook..dont know if it was smoke or steam or what...
------------------ '91 GT,91K,T-5,air silencer removed,racing clutch(previous owner put in so dont know what kind),K&N air filter,Mac long tubes,Cat-back,off road H,FMS 9mm wires,Competition gauges,C&L 76mm MAF Waiting install:TFS street heat,Accufab TB Future Mods:3.73's,Pro 5.0,TFS heads,TFS stage 1 cam,lakewood struts/shocks,nitto DR's ICQ#35670781 ![]() |
![]() |
![]() |
![]() |
#4 |
The Photoshop Guru
Join Date: Feb 2001
Location: Mecca, Indiana
Posts: 1,419
|
![]() What color was the smoke? Could it be an intake leak? Spray some WD-40 around your intake and see if the idle changes. If so you are leaking. Go to Auto Zone and get a vacuum tester - $20. Test the vacuum to see if you have at least 15 inches.
------------------ Too much to list. Best ET on the car so far with stock 2.73 gears - 13.73@102mph Indiana Stangers Association Buy your parts here ICQ# 42269241 |
![]() |
![]() |
![]() |
#5 |
Registered Member
Join Date: Dec 1998
Location: Chicago, IL. USA
Posts: 77
|
![]() Definitely sounds like vacuum leak, bent pushrods wouldn't happen from that..oils completely different system. Like the other post said, check the big line, also check so see if you put lines in the wrong places...get a manual if you don't have one. Brakes are vacuum assisted-so thats tied into the same situation. Also, smoke under hood, you might have just spilled something, does it smell like antifreeze or oil? Never had the problem on a car, but on a motorcycle once I didn't hook up a vacuum line and it seemed to burn oil, might have been pulled through the valve stem seal somehow? anyway...check lines! Someone above had stated spray WD40, this works forsure, but leaves a messy film all over! If you spray starting fluid around(not tons, this stuff can be dangerous) and the car revs, then you have a leak in the area you just sprayed.
[This message has been edited by Shawn (edited 06-13-2001).] |
![]() |
![]() |
![]() |
#6 |
Registered Member
Join Date: Aug 2000
Location: Wisconsin
Posts: 879
|
![]() i dont now what color the smoke was.....after work ill see what my buddy has found out and get back to you guys
------------------ '91 GT,91K,T-5,air silencer removed,racing clutch(previous owner put in so dont know what kind),K&N air filter,Mac long tubes,Cat-back,off road H,FMS 9mm wires,Competition gauges,C&L 76mm MAF Waiting install:TFS street heat,Accufab TB Future Mods:3.73's,Pro 5.0,TFS heads,TFS stage 1 cam,lakewood struts/shocks,nitto DR's ICQ#35670781 ![]() |
![]() |
![]() |
![]() |
#7 |
Registered Member
Join Date: Oct 1999
Location: Cincinnati, Ohio
Posts: 1,575
|
![]() Also, are you sure you used the correct lower intake gaskets? and did the lower intake line up fine?
|
![]() |
![]() |
![]() |
#8 |
Registered Member
Join Date: Aug 2000
Location: Wisconsin
Posts: 879
|
![]() well worked on it yesturday and it started..but i had coolant not driping but pouring out the exhaust..tore it down and found the passanger side lower gasket had slide forward and was leting coolant throw..ordered new gaskets...
also..are you suppose to use that black liquid gasket stuff on the upper and lower intake gaskets to or just the cork gaskets? ------------------ '91 GT,91K,T-5,air silencer removed,racing clutch(previous owner put in so dont know what kind),K&N air filter,Mac long tubes,Cat-back,off road H,FMS 9mm wires,Competition gauges,C&L 76mm MAF Waiting install:TFS street heat,Accufab TB Future Mods:3.73's,Pro 5.0,TFS heads,TFS stage 1 cam,lakewood struts/shocks,nitto DR's ICQ#35670781 ![]() |
![]() |
![]() |
![]() |
#9 |
Registered Member
Join Date: Jan 1999
Location: Clayton, North Carolina, USA
Posts: 803
|
![]() You don't need gasket sealer on the upper intake, the lower you should use the RTV on the front and rear of the intake. Where the cork gaskets are located. I prefer to use just RTV and no gasket in this location, the cork ones tend to slip out occasionally. Use a large 1/4" bead if you don't use gaskets here. I like to use alignment pins so that when you lower the intake into place it drops straight down creating a good seal. I took 4 5/16 x 3" or 4" long bolts, cut the heads off and grind a radius on the ends to make alignment pins.
------------------ fordgasm CLICK HERE to see my 87 GT |
![]() |
![]() |
![]() |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
Rocker adjustment | zach0 | Classic Mustangs | 3 | 04-24-2004 12:28 PM |
Edelbrock RPM intake install problems | jruppert | Windsor Power | 4 | 03-04-2004 05:05 PM |
Cobra Intake? | 95mustanggt | Windsor Power | 5 | 10-01-2002 09:55 AM |
upper intake and egr spacer install..... | scale | Windsor Power | 3 | 08-18-2002 11:37 PM |
new coolant leak after intake install | fiveohpatrol | Windsor Power | 15 | 03-04-2001 09:15 PM |