© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
03-29-2004, 09:28 PM | #1 |
Registered Member
Join Date: Sep 2003
Location: Mountaintop, PA
Posts: 634
|
Rev Limiter?
Can someone tell where the rev limiter is set on my car from the factory? What is a safe point to have it raised? And, when racing, where do you shift?
Thanks guys!
__________________
"Children should not get cancer, but they do!" Help a child with cancer at www.homeoftheirown.org My Stang: 2000 Mustang GT Vert - Steeda Tri-Ax Shifter; C&L Plenum; BBK 75 mm TB; Steeda Strut Tower Supports; Black "Deep Dish" Bullet Wheels; FRPP 4.10's; Steeda Subframes; SLP Catback & SLP Catted X-Pipe; SCT 4 Position Chip with 3 custom tunes; Steeda CAI; Venom-1000 Nitrous; Roush Stage 3 Body Kit; Bullet Suspension Package (on the way) |
03-30-2004, 03:04 PM | #2 |
Mustang Addict
Join Date: Jan 2001
Location: McKinney, TX
Posts: 1,294
|
Your rev limiter should be at 6250rpm. With the stock internals I wouldn't go much above that.
When I race I shift at redline in 1st and 2nd and at about 5500 from 3-4 (5-speed).
__________________
Strike down the unroadworthy! 2000 GT Atl. Blue: '03 Cobra motor - 465rwhp/473rwtq, T-56 6-speed, full MM TA/PH & tubular K-member suspension, Saleen body, 17" Torq-Thrust II's, M/T ET Street radials, and lots more '94 Rio Red Cobra: All the bolt-ons, 3.73s |
03-30-2004, 03:27 PM | #3 |
Registered Member
Join Date: Sep 2003
Location: Mountaintop, PA
Posts: 634
|
Thanks! That's actually about how I play it. I was not sure if 5500 was too low and if I was leaving too much speed on the table...so to speak. I used an engine analyzer program a while back, and I think it recomended 5800 rpms, but I am more comfortable with 5500.
I have never hit the rev limiter on this car and I hope to keep it that way.
__________________
"Children should not get cancer, but they do!" Help a child with cancer at www.homeoftheirown.org My Stang: 2000 Mustang GT Vert - Steeda Tri-Ax Shifter; C&L Plenum; BBK 75 mm TB; Steeda Strut Tower Supports; Black "Deep Dish" Bullet Wheels; FRPP 4.10's; Steeda Subframes; SLP Catback & SLP Catted X-Pipe; SCT 4 Position Chip with 3 custom tunes; Steeda CAI; Venom-1000 Nitrous; Roush Stage 3 Body Kit; Bullet Suspension Package (on the way) |
04-01-2004, 12:09 AM | #4 |
Registered Member
Join Date: Jul 2003
Location: Sebastopol CA
Posts: 169
|
Well I have hit the rev limiter once (missed 2-3 shift, ouch)... and it kicked in before 6250 on my car!... It was at about 6000
Was the rev limiter changed on different year models?? blake... whats that front bumper you got?? I like that a lot! blue... I just noticed that you are from Sebastopol... same here man! What a small world We'll have to meet up sometime, when mines a little more built of coarse.. haha!
__________________
Torch Red '02 GT Convertible 5 spd BBK long tubes, BBK h-pipe, MAC mufflers, K&N w/ silencer trimmed, FRPP 70mm throttle body, C&L plenum, Mobil1 synthetic fluids, FRPP aluminum drive shaft, Steeda Tri-Ax shifter, FRPP 4.10's, 18x9 & 18x10 Saleens with Dunlop SP Super Sport Race rubber, Mach1 grill (GT delete), & Mach1 bumper chin! Click here for pictures & more info! If you are in Northern California, check out North Bay Mustang Club for local meets and cruises! |
04-01-2004, 07:29 AM | #5 |
Registered Member
Join Date: Sep 2003
Location: Mountaintop, PA
Posts: 634
|
Not sure on the rev limiter question, but I don't know if those needles are real accurate. There is a way to get your odometer to display digital rpms. I will find the instructions. There was an old thread a few months ago too. Every once in a while, this question comes up.
I made two changes to the front of my car. One was to delete the stock grill and the other was to add a chin spoiler. There are lots of places that sell these. The grill deletes run $45 - $90 and the chin spoilers are $60 - $90 from I can remember. www.mustangtuning.com is where I got mine...they had the best prices that I could find and include shipping. This is essentially what the front-end of a Mach 1 looks like minus the shaker-hood of course. I keep my stock parts in case I need to sell the car and make it original. I have a friend with an '03 Vette. Believe it or not, the rear window (which was classic only to '03) was considered ugly by many back then. Many guys put in the '04 windows in their '03's and the cars have lost much value now unless you find an original '03 window. My stang will probably NEVER be that vintage, but I always remember that example and therefore keep my stock parts.
__________________
"Children should not get cancer, but they do!" Help a child with cancer at www.homeoftheirown.org My Stang: 2000 Mustang GT Vert - Steeda Tri-Ax Shifter; C&L Plenum; BBK 75 mm TB; Steeda Strut Tower Supports; Black "Deep Dish" Bullet Wheels; FRPP 4.10's; Steeda Subframes; SLP Catback & SLP Catted X-Pipe; SCT 4 Position Chip with 3 custom tunes; Steeda CAI; Venom-1000 Nitrous; Roush Stage 3 Body Kit; Bullet Suspension Package (on the way) |
04-01-2004, 01:18 PM | #6 |
Registered Member
Join Date: Jul 2003
Location: Sebastopol CA
Posts: 169
|
Cool thanks!
I'm gonna check that site out
__________________
Torch Red '02 GT Convertible 5 spd BBK long tubes, BBK h-pipe, MAC mufflers, K&N w/ silencer trimmed, FRPP 70mm throttle body, C&L plenum, Mobil1 synthetic fluids, FRPP aluminum drive shaft, Steeda Tri-Ax shifter, FRPP 4.10's, 18x9 & 18x10 Saleens with Dunlop SP Super Sport Race rubber, Mach1 grill (GT delete), & Mach1 bumper chin! Click here for pictures & more info! If you are in Northern California, check out North Bay Mustang Club for local meets and cruises! |
04-01-2004, 03:17 PM | #7 |
Mustang Addict
Join Date: Jan 2001
Location: McKinney, TX
Posts: 1,294
|
JBeryleC - We're having a meet on April 24th for the North Bay Mustang Club at Mt. Tamalpais. Let me know if you're interested and I'll get you the info. It's usually a good time. We barbecue and do a cruise.
As for the rev limiter I believe someone told me that they reduced the rev limit to 6000 on '02+, but I'm not positive.
__________________
Strike down the unroadworthy! 2000 GT Atl. Blue: '03 Cobra motor - 465rwhp/473rwtq, T-56 6-speed, full MM TA/PH & tubular K-member suspension, Saleen body, 17" Torq-Thrust II's, M/T ET Street radials, and lots more '94 Rio Red Cobra: All the bolt-ons, 3.73s |
04-01-2004, 04:43 PM | #8 |
Registered Member
Join Date: Jul 2003
Location: Sebastopol CA
Posts: 169
|
blue.. yes please.. will you email me the details?
Thanks man I still can't believe we're in the same small town.. ha!
__________________
Torch Red '02 GT Convertible 5 spd BBK long tubes, BBK h-pipe, MAC mufflers, K&N w/ silencer trimmed, FRPP 70mm throttle body, C&L plenum, Mobil1 synthetic fluids, FRPP aluminum drive shaft, Steeda Tri-Ax shifter, FRPP 4.10's, 18x9 & 18x10 Saleens with Dunlop SP Super Sport Race rubber, Mach1 grill (GT delete), & Mach1 bumper chin! Click here for pictures & more info! If you are in Northern California, check out North Bay Mustang Club for local meets and cruises! |
04-01-2004, 07:04 PM | #9 |
Mustang Addict
Join Date: Jan 2001
Location: McKinney, TX
Posts: 1,294
|
Yeah, small world. There is also a guy named Rob that I've seen on the message boards with a gold 2000GT with 524rwhp that lived in Sebastopol (I think he may have moved recently).
__________________
Strike down the unroadworthy! 2000 GT Atl. Blue: '03 Cobra motor - 465rwhp/473rwtq, T-56 6-speed, full MM TA/PH & tubular K-member suspension, Saleen body, 17" Torq-Thrust II's, M/T ET Street radials, and lots more '94 Rio Red Cobra: All the bolt-ons, 3.73s |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Rev limiter or VSS, what is causing this problem!!! | moponys | Windsor Power | 6 | 10-28-2003 12:49 AM |
speed limiter? | ac97gt | Blue Oval Lounge | 2 | 08-24-2003 03:34 AM |
what are the 02 rev limiter and peak power RPM? | MineralGray02K | Modular Madness | 2 | 08-01-2002 05:03 PM |
limiter on the Mustang? | Torinalth | Modular Madness | 6 | 07-16-2002 12:00 PM |
rev limiter | craig5.0 | Windsor Power | 31 | 06-17-2002 04:21 PM |