![SEARCH](http://www.mustangworks.com/images/search.png)
![The Mustang Works](http://www.mustangworks.com/images/mw_footer_logo.gif)
© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
![]() |
#1 |
Registered Member
Join Date: Apr 1999
Location: Massachusetts
Posts: 84
|
![]() I just purchased a 91 LX a week and 1/2 ago and have already made some modifications. A added a Mac Cat-back system, Mac Cold Air induction kit, Pro 5.0 Shifter, Pulleys, and gave her a good tune up. I plan on getting gears within the next couple of weeks. I was wondering if I should go with 3.55's or 3.73's? I do plan on adding a Holley Systemax 2 system in the future and then a supercharger, vortech, ATI?.. Any suggestions would be great on what gears to get and why.. I also plan on getting a new throttle body in the near future and was wondering what size I should go with, a 65mm or 70mm? Keep in mind my previous mods and also my future mods...
Thanks... |
![]() |
![]() |
![]() |
#2 |
or '331 LX Eric'
Join Date: Jan 1999
Location: Columbus, Ohio
Posts: 2,142
|
![]() Since you will be adding a supercharger in the future, I would go with the 3.55's. Good street manners, good highway gas mileage and enough gear to get you down the track in reasonable fashion.
As for the TB, I think the Holley intake has a 70mm opening , but I am not sure on this. If it does, then you might as well go with the 70mm. I wouldn't go any bigger unless you are going to make your Stang into a drag-only type machine. Congratulations on your purchase! ![]() E ------------------ 1991 5.0 LX Coupe - 38,000 miles 13.17 @ 106.14 mph w/ 2.138 60' [This message has been edited by 302 LX Eric (edited 06-25-2001).] |
![]() |
![]() |
![]() |
#3 |
The Dude
Join Date: Feb 2001
Location: Arlington, VA
Posts: 1,262
|
![]() I agree, cause you are going to be blowing it later, get 3.55s.
|
![]() |
![]() |
![]() |
#4 |
Registered Member
Join Date: Apr 1999
Location: Massachusetts
Posts: 84
|
![]() Thanks Guys.. I'm gonna go check and see if Summit has the Holley 70mm TB and spacer. I think they do.. I'm also gonna see if they have a Pro-M 75mm MAF. I'll need to schedule an appointment for the gears, I think you sold me on the 3.55's. I think it's gonna run me around $500 for them to do the swap. There aren't too many places around here to get work like that done..
Thanks Again.. |
![]() |
![]() |
![]() |
#5 |
Guest
Posts: n/a
|
![]() 3.55's and the 70 mm TB!
------------------ '90 LX 5.0; 12K original miles (no sh*&); 3.55 gears; pulleys;Edelbrock Performer Heads; BBK shorties; MSD 6AL box w/ blaster 2 coil; Motorsport E303 cam; Pro-M 75mm MAF; BBK 70mm TB; Eibach spring kit; Southside welded subs; K&N cone filter charger; Hurst shifter; fiberglass turbo hood; A/C-less; rear seat-less; cat-less; 2 chamber Flos; Corbeau racing seats (fronts); 30# injectors; JMS Chip; 190 lb fp; TFS track heat Intake (12.299 @ 113) |
![]() |
![]() |
#6 |
I'd rather be basketweaving
Join Date: Feb 2000
Location: Indianapolis
Posts: 2,551
|
![]() 500 is a little steep, most people pay about 400, but a good thing to try is to go to a few ford dealership service departments and ask if any of the guys does side work on the weekend and could do the gears, theres a guy here in my town that will do the swap for about $80 labor
------------------ 88 Notch, 3.73's, Ported E7's, Explorer int. w/ ported lower, pulleys, 1.7RR's, BBK headers, off-road H-pipe, flowmasters, subframe connectors, 65mm TB, shift kit, March ram air ,MSD coil, U/L control arms, 155lph fuel pump, cheap 2800 stall, Crane Adj.FPR, best 1/4--> 13.77@101.35 |
![]() |
![]() |
![]() |
|
|