© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
12-12-2002, 09:41 PM | #1 |
Registered Member
Join Date: Sep 2002
Location: Naperville, IL, USA
Posts: 76
|
Low Budget Weight Reduction
Ok I'm on a very, very low budget right now, mainly because I'm a high school student, but I still need to go fast. I think I'm gonna have to lose some weight in my '90 LX. Where in my car is all this sound material that I can take out? Also any other ideas? I'm not really looking to spend money so please don't tell me I need a K-member and stuff like that. I'm really broke and looking for some speed.
__________________
There will always be someone faster then you. |
12-12-2002, 10:47 PM | #2 |
Registered Member
Join Date: Aug 2002
Location: Gonzales, Louisiana
Posts: 153
|
i probably dropped over 100 lbs and spent 50 bucks
UPR a/c delete, removed front sway bar, removed rear seats/carpet, spare tire, jack etc i plan on taking out the smog pump, power steering and whatever else i can find pretty soon all that for nothing of course If i remove the p/s pump, ill need a new belt, but that's about it.... |
12-13-2002, 12:50 PM | #3 | |
2 Stangs in the Stable
Join Date: Apr 2002
Location: Baytown, TX
Posts: 1,209
|
Quote:
As for the original question, I also removed the carpet and carpet padding. There is sound deadning insulation behind the plastic molding in the back side of the car. Mine wieghs 3450 w/ me sitting in it. But I weigh almost 300 lbs. I know, I know, Jenny Craig Blah Blah Blah!!! Caymon
__________________
'90 GT Under construction Best E.T. = Fast @ High Speeds - OK So I Lie. So What!!! 04 F-150 STX 4.2L 5 spd Rice Haters Club Member #128 |
|
12-13-2002, 12:52 PM | #4 | |
Registered Member
Join Date: Aug 2002
Location: Gonzales, Louisiana
Posts: 153
|
Quote:
About the rack, I'm pretty sure you don't need to change the rack, it will just be alot easier to turn with a manual rack than it would with a "power" rack w/ the pump removed. |
|
12-15-2002, 10:57 AM | #5 |
Registered Member
Join Date: Jul 1999
Location: INDIANAPOLIS
Posts: 404
|
Don't forget the dog bone on the rear end.
__________________
old S trim combo 10.13@ 135 New YS combo = 680RWHP (no times) |
12-15-2002, 07:59 PM | #6 |
Registered Member
Join Date: Sep 2002
Location: Naperville, IL, USA
Posts: 76
|
yeah what the hell is this dog bone thing that everyone talks about? ive heard it before but im not clear on what it is.
__________________
There will always be someone faster then you. |
12-15-2002, 08:15 PM | #7 |
Registered Member
Join Date: Oct 2000
Location: Elizabethton,TN U.S.
Posts: 41
|
It is bolted on the bottom of the rearend housing. It is directly under drive shaft bolts and it is held on by 2 bolts and weighs alot. And really useless..
|
12-15-2002, 08:46 PM | #8 |
Registered Member
Join Date: Jul 1999
Location: INDIANAPOLIS
Posts: 404
|
The dogbone was used to take out driveline vibrations. It was suppose to help with stock gears, most people toss them after installing new gears.
__________________
old S trim combo 10.13@ 135 New YS combo = 680RWHP (no times) |
12-15-2002, 11:33 PM | #9 |
Registered Member
Join Date: Sep 2002
Location: Boston
Posts: 592
|
I pulled 380 lbs off my mustang, here is the list:
Removed front bumper and supports Removed light bar and remounted fogs removed skirt around lower engine bay Removed a/c radiator removed all a/c hoses removed a/c compressor removed all tubes and hoses for heater core removed hood heatshield pad battery to the trunk stripped cruise components Stripped airbag sensors and airbag and brackets stock EEC-4 removed with all relays and 25 lbs of wiring Pulled all soundproofing except under carpet Removed frame for dashboard (doesnt need it) pulled entire fan and heater tract assembly including parts in dash Installed 130 cfm pc fan hooked to central vents with tube pickup off headers disabled rear defroster assembly and pulled all relays and wiring hooked foglights to headlight switch Pulled radio support bracket Pulled shifter boot plate cut all wiring to console Replaced armrest unit with 90' convertible plate removed back seat support frame flipdowns removed back seat support bars removed rear bumper I-beam and supports removed rear axle damper removed pinion snubber strike plate removed spare tire + jack + iron (never came with one) removed tire well plate removed front bumper and support beams -315 pounds + tire/jack/iron (65 lbs?) and still going the a/c elimanator bracket is the only thing that costs money but not if you are killing the ps too have fun. By the way, the extra noise is negligible and the ride quality is so much better with that extra weight gone
__________________
91 GT Carb conversion, holley 600 double pumper, edelbrock performer intake, FMS "C" drop springs, march 1000 underdrive pullies, crane 1.7 roller rockers, GT-40P headers, bassani x pipe, american thunder catback, FMS 4.56's, msd aL6, trunkmount battery, A/C eliminator kit, 3000 stall tci streetfighter, AOD with transgo kit, A+ servo, 300M hardened lockup shaft, kevlar bands and 28,000 gvw trans cooler, 3 core radiator, 300 lbs stripped with a full interior |
12-16-2002, 11:21 AM | #10 |
Registered Member
Join Date: Jul 1999
Location: INDIANAPOLIS
Posts: 404
|
Up date your starter to a 92-93 style. Thats a few pounds plus header clearence. But it now costs you for a new starter.
__________________
old S trim combo 10.13@ 135 New YS combo = 680RWHP (no times) |
12-16-2002, 05:51 PM | #11 | |
2 Stangs in the Stable
Join Date: Apr 2002
Location: Baytown, TX
Posts: 1,209
|
Quote:
Caymon
__________________
'90 GT Under construction Best E.T. = Fast @ High Speeds - OK So I Lie. So What!!! 04 F-150 STX 4.2L 5 spd Rice Haters Club Member #128 |
|
12-16-2002, 07:39 PM | #12 |
Registered Member
Join Date: Sep 2002
Location: baltimore, md
Posts: 220
|
When my starter went i picked up a gear reduction starter off a 94 f-150 with a 5.0 for $5 from a junkyard and it had been rebuilt less than 5 months earlier going by the sticker from precision on the side (Precision also has a lifetime warranty on there domestic starters) . It turns the motor over alot faster and it is alot easier to put on and off because of the size difference and definately is lighter.
hope this helps
__________________
90 LX Hatchback 306, AFR 165's 58cc, E303, 1.6 roller rockers, 70mm throttle body, cobra intake, bbk fenderwell, bbk longtubes, x-pipe, flowmasters, pullies, msd 6a, crane ps-92, stock MAF sensor, electric fan, No AC, No air pump, flaming river quick ratio rack C-4, 3500 stall, 373's, aluminum driveshaft SSM Lift bars, , sub frame connectors, strut tower brace 12.57 @105.12mph w/ 1.686 60ft before bbk longtubes (with equal shorties) ----------------------------------------- 86 tube chassis coupe - the trailor queen |
12-16-2002, 07:56 PM | #13 |
Registered Member
Join Date: Jul 1999
Location: INDIANAPOLIS
Posts: 404
|
The starter is a direct bolt in but you have to change a few wires. Its really simple. All you do is swap over the big wire from the solinoid so it is hot all the time. Then you have to add a 10-12 gauge wire that goes from the where the starter lead was down to the starter solinoid. Now when you try to start the car it pulls in the usually solinoid and also pulls in the starter solinoid.
__________________
old S trim combo 10.13@ 135 New YS combo = 680RWHP (no times) |
12-16-2002, 08:23 PM | #14 |
Registered Member
Join Date: Sep 2002
Location: baltimore, md
Posts: 220
|
Just make sure you use good wire and connectors on that jumper wire on the solenoid because you dont wanna get stranded somewhere cause of something stupid. I speak from experience. Luckly i thought of that and held the wire on the connector while someone started it. At first i though i had a dead short somewhere but the jumper wire broke right at the connector. You have to remember it gets hot down there with those headers right there and on my car i have the trans lines going right by there too.
__________________
90 LX Hatchback 306, AFR 165's 58cc, E303, 1.6 roller rockers, 70mm throttle body, cobra intake, bbk fenderwell, bbk longtubes, x-pipe, flowmasters, pullies, msd 6a, crane ps-92, stock MAF sensor, electric fan, No AC, No air pump, flaming river quick ratio rack C-4, 3500 stall, 373's, aluminum driveshaft SSM Lift bars, , sub frame connectors, strut tower brace 12.57 @105.12mph w/ 1.686 60ft before bbk longtubes (with equal shorties) ----------------------------------------- 86 tube chassis coupe - the trailor queen |
12-17-2002, 12:01 PM | #15 |
Registered Member
Join Date: Jul 1999
Location: INDIANAPOLIS
Posts: 404
|
Drag stang , what do you mean by jumper wire ? I didn't use a jumper wire on mine. I added a wire, and moved the large wire from one side of the fender solinoid to the other, thats it.
__________________
old S trim combo 10.13@ 135 New YS combo = 680RWHP (no times) |
12-17-2002, 07:49 PM | #16 |
Registered Member
Join Date: Sep 2002
Location: baltimore, md
Posts: 220
|
I used a wire to jump the solenoid on the starter since there is already a seperate solenoid for the stock starter. Im just kinda doing the same thing with that wire as if you were to jump a solenoid with a screwdriver under the hood to start the car.
__________________
90 LX Hatchback 306, AFR 165's 58cc, E303, 1.6 roller rockers, 70mm throttle body, cobra intake, bbk fenderwell, bbk longtubes, x-pipe, flowmasters, pullies, msd 6a, crane ps-92, stock MAF sensor, electric fan, No AC, No air pump, flaming river quick ratio rack C-4, 3500 stall, 373's, aluminum driveshaft SSM Lift bars, , sub frame connectors, strut tower brace 12.57 @105.12mph w/ 1.686 60ft before bbk longtubes (with equal shorties) ----------------------------------------- 86 tube chassis coupe - the trailor queen |
12-17-2002, 07:55 PM | #17 |
Registered Member
Join Date: Jul 1999
Location: INDIANAPOLIS
Posts: 404
|
I was just wondering. When I talked with the guys that make the aftermaket starters (can't remember their name) they said I had mine wired wrong. At the time I had a delayed start. I changed things around to the way I have it now, and everything is perfect. This is also the way the factory did it in 92-93.
So you leave everything the same as it was, but add a short 3-4" jumper from lug on the starter to the solinoid on the starter. Correct ?
__________________
old S trim combo 10.13@ 135 New YS combo = 680RWHP (no times) |
12-17-2002, 11:45 PM | #18 |
Registered Member
Join Date: Sep 2002
Location: baltimore, md
Posts: 220
|
Yep, thats all i did...works great...once i put some quaility wire on it.
__________________
90 LX Hatchback 306, AFR 165's 58cc, E303, 1.6 roller rockers, 70mm throttle body, cobra intake, bbk fenderwell, bbk longtubes, x-pipe, flowmasters, pullies, msd 6a, crane ps-92, stock MAF sensor, electric fan, No AC, No air pump, flaming river quick ratio rack C-4, 3500 stall, 373's, aluminum driveshaft SSM Lift bars, , sub frame connectors, strut tower brace 12.57 @105.12mph w/ 1.686 60ft before bbk longtubes (with equal shorties) ----------------------------------------- 86 tube chassis coupe - the trailor queen |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
weight reduction on a 94 cobra | mak375 | Windsor Power | 2 | 11-21-2003 10:20 AM |
raced a Supra Twin Turbo | Stang35th | Stang Stories | 63 | 08-23-2003 12:36 AM |
Please Comment of Speed Secret # 2 | jim_howard_pdx | Windsor Power | 20 | 11-06-2002 11:44 AM |
Weight Reduction | pac663 | Windsor Power | 4 | 09-15-2001 05:29 PM |
Weight reduction | Dino | Modular Madness | 4 | 08-09-2000 05:56 PM |