![SEARCH](http://www.mustangworks.com/images/search.png)
![The Mustang Works](http://www.mustangworks.com/images/mw_footer_logo.gif)
© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
![]() |
#1 |
Registered Member
Join Date: Oct 1998
Location: Suburban Chicago, Hanover Park
Posts: 695
|
![]() I put in a new quadrant, firewall adjuster and a new cable a while back and have been having a problem with the clutch not fully disengaging ever since. I've adjusted the adjuster every way I know how and because of this problem I actually shredded the splines that the synchros go in on second gear in my T5. I replaced the clutch, clutch fork, pilot bearing and throwout bearing and the problem persisted. I just had the tranny rebuilt and i still have the same problem. Anybody have any ideas on how I can check the adjustment? Has anyone else ever had this problem? I don't want to trash another trans. I put spacers on the quadrant to make sure it lined up with the cable too. I'm out of ideas. Anything that can help I'd appreciate. TIA
|
![]() |
![]() |
![]() |
#2 |
Registered Member
Join Date: Nov 2001
Location: SanAntonio, Tx
Posts: 734
|
![]() I have heard of people installing them backwards? but my D&D has been great, i did however, have to back out the firewall adjuster almost all the way out to get the slop out of the pedal, i cant think of anything but your clutch might just be worn? dunno....
__________________
Police package 5spd 90 Lx, Stock original motor, 3.27grs, BM fan, fms 10.5 clutch, D&D quadrant, and adjuster, ADS chip, 180 stat, mac cai, mac h-pipe, mac subframe connectors, ASP crank pulley, ripper shifter, 26x10.5 M/T sport pros welds. 246 hp according to analyzer ![]() Race weight: 3,120 E.t-13.57 with 26x10.50's e.t. streets. 1.88 60' mph- 99.92 mph |
![]() |
![]() |
![]() |
#3 |
Registered Member
Join Date: Oct 1998
Location: Suburban Chicago, Hanover Park
Posts: 695
|
![]() Nope it's in right, and the clutch has been replaced. There has to be something wrong with how I'm adjusting it or something like that. I don't know if there's any way to check the adjustment, like if it's too tight and the tines of the pressure plate are actually pressing against the clutch and keeping it engaged or something like that. I'm pretty much stumped and I don't want to replace the clutch and rebuild the trans again because of this problem.
![]() |
![]() |
![]() |
![]() |
#4 |
Registered Member
Join Date: Apr 2002
Location: racine ,wi
Posts: 691
|
![]() I had that prob.
with a cable I had it turned out that the cable for what ever reason was streached from the start. have you tried a diff cable?
__________________
RUN IT STAIGHT AND RUN IT HARD ________ Novi 2000 60' 1.46 1/4 10.67 mph 126.5 _________ |
![]() |
![]() |
![]() |
#5 |
Registered Member
Join Date: Oct 1998
Location: Suburban Chicago, Hanover Park
Posts: 695
|
![]() Thanks, yeah as a matter of fact I ordered one today (my 3rd). I got some advice from the Summit tech line I might try out too. Gotta see if I can adjust the clutch (not sure if I can even measure it) to btween .030 and .040 inches between the clutch and the flywheel when the clutch is depressed. They said I also might need to put in a clutch stop, weld a plate to the back of the pedal so I don't mash it too far. Either that or I just need to do alot of experimenting with adjustments. The problem is I only have the problem at high rpm, like 5500-5800rpm, and when it isn't right I'm messing up the synchros with the grinding
![]() |
![]() |
![]() |
![]() |
#6 |
Registered Member
Join Date: Apr 2002
Location: racine ,wi
Posts: 691
|
![]() dont feel bad Im on my 4th cable
__________________
RUN IT STAIGHT AND RUN IT HARD ________ Novi 2000 60' 1.46 1/4 10.67 mph 126.5 _________ |
![]() |
![]() |
![]() |
#7 |
Registered Member
Join Date: Jan 1999
Location: Las Vegas NV
Posts: 286
|
![]() I had the same problem and found an easy cure that was free.
The plastic portion of the clutch cable that sits inside the firewall adjuster was too long and I shortened it by using a dremel with a cutting disc on it. This allowed the whole portion of the cable to sit inside the adjuster to where the largest diameter of the firewall adj. and the cable were butted up against each other. This is the best I could explain it. I can try and get some pics if you need. Also check the houseing your throwout bearing rides on. They tend to get cut into from the throwout bearing and the bearing could be getting hung up on it. Summit sells one that is made of steal which will fix this problem. If this is whats wrong on your car. |
![]() |
![]() |
![]() |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
CLUTCH PROBLEMS (Fork??) | drewmp28 | Windsor Power | 6 | 07-18-2004 11:51 PM |
'65 - Pull Away Problems - Action Plan | geordie | Classic Mustangs | 0 | 05-14-2002 01:43 PM |
Clutch Problems | blue302 | Windsor Power | 3 | 09-10-2001 01:37 PM |
Clutch quadrant | HKstang | Windsor Power | 1 | 03-06-2001 04:55 PM |
billed 5 times to install clutch by Pauls Auto, please read and give opinions (long) | beefcake | Blue Oval Lounge | 2 | 02-23-2001 03:05 PM |