![SEARCH](http://www.mustangworks.com/images/search.png)
![The Mustang Works](http://www.mustangworks.com/images/mw_footer_logo.gif)
© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
![]() |
#1 |
Tires Fear Me...
Join Date: Jan 2001
Posts: 867
|
![]() I hate this.. Just got time last night to drive my car actually for the first time with all the new mods..I have been to busy lately with school to drive it. The thing is a nightmare. I have all stock suspension. Stock turbines with 235/70/15 Hoosier GT's. All I do is sit and spin through 1 and 2nd gear. Even though I cant go anywhere it still sounds meaner than hell..Well my question is what is a CHEAP way to get some traction to the ground. |
![]() |
![]() |
![]() |
#2 |
The Dude
Join Date: Feb 2001
Location: Arlington, VA
Posts: 1,262
|
![]() Lower control arms methinks. What all do you have? Can you reall not go anywhere?
|
![]() |
![]() |
![]() |
#3 |
Tires Fear Me...
Join Date: Jan 2001
Posts: 867
|
![]() I can go but not very well...when i punch it to launch it just wont go! see sig for mods..
------------------ 347 Stroker Motor: Balanced, 24lb Bosch Injectors, Cobra Computer, Cobra Transmission, Extude Ported and Polished Upper and Lower, GT40 Milled Ported and Polished Heads, B303 Cam, BBK 1 5/8 Headers, Holley Fuel Regulator, March Underdrive Pulleys, Electric Fan, Accel Performance Coil, Accel 300+ Racing Wires, Ram Air, K&N Filter, 79mm Mass Air Unit, FlowMaster Exhaust w/BBK Offroad H-Pipe, Hurst Short Throw Shifter, 3:55 Gears, Ram Clutch, Cross Drilled Rotors, High Tolerant Painted Calipers |
![]() |
![]() |
![]() |
#4 |
Registered Member
Join Date: Jun 2000
Location: Belleville Il, USA
Posts: 234
|
![]() if you're looking to stay cheap, then try a set of the factory five control arms, get the uppers and lowers. also, next time you buy tires get something a lil wider, at least a 245. no fun spending all your money to make power and then not go anywhere is it?
![]() ------------------ 1990lx coupe, balanced 302, gt40p heads, wolv 1087 cam, 1.7rr's, 65mm tb, 75mm maf, comp box on top of cobra lower, anderson ford pms, full exhaust, drag type susp. and tubular front end, 3.55's. traps 105mph before some mods, look for 110mph very soon |
![]() |
![]() |
![]() |
#5 |
Tires Fear Me...
Join Date: Jan 2001
Posts: 867
|
![]() How much do those controller arms cost??
------------------ 347 Stroker Motor: Balanced, 24lb Bosch Injectors, Cobra Computer, Cobra Transmission, Extude Ported and Polished Upper and Lower, GT40 Milled Ported and Polished Heads, B303 Cam, BBK 1 5/8 Headers, Holley Fuel Regulator, March Underdrive Pulleys, Electric Fan, Accel Performance Coil, Accel 300+ Racing Wires, Ram Air, K&N Filter, 79mm Mass Air Unit, FlowMaster Exhaust w/BBK Offroad H-Pipe, Hurst Short Throw Shifter, 3:55 Gears, Ram Clutch, Cross Drilled Rotors, High Tolerant Painted Calipers |
![]() |
![]() |
![]() |
#6 |
Registered Member
Join Date: Jun 1999
Location: North Haven,CT
Posts: 336
|
![]() Try not flooring it
![]() With those mods thats no surprise, and you sound upset over it..... Get some nice sticky tires and let it rip...if you think you're gonna come out of the hole at 5 grand on the street with your average street tire you better open your eyes.....you got a nice setup there ------------------ 1992 5.0 LX, V-1 S-Trim @8LBS,Edelbrock 6037 Heads,Cobra Intake,E-303,1.6 Roller Rockers,65MM Holley TB, 75 MM Pro M Mass Air, 190 LPH FP,24 lb injectors,MSD 6A and BTM,BBK equal length shorties,offroad h-pipe,Mac Flowpath Mufflers,Pro 5.0, 3.73's,Motorsport "C" springs,welded subframe connectors,Ponies w/ 225/50 Nitto NT 450's on front,255/50 BFG Drags out back,93 Cobra Spoiler Daily driver: 89 Coupe with 208K plus, BBK shorties,offroad h-pipe,2-chamber flowmasters with dumps, |
![]() |
![]() |
![]() |
#7 |
Registered Member
Join Date: Jun 2000
Location: Belleville Il, USA
Posts: 234
|
![]() im pretty sure you can get the pair for about $250, thats without tax and shipping though. obviously these arent the highest quality arms out there, but the price to performance ratio is pretty nice, and you said you need inexpensive solutions. check MM&FF for their advertisements. hope this helps you, nick
|
![]() |
![]() |
![]() |
#8 |
Tires Fear Me...
Join Date: Jan 2001
Posts: 867
|
![]() I was looking for something half that price..anyone running traction bars? would those work???
------------------ 347 Stroker Motor: Balanced, 24lb Bosch Injectors, Cobra Computer, Cobra Transmission, Extude Ported and Polished Upper and Lower, GT40 Milled Ported and Polished Heads, B303 Cam, BBK 1 5/8 Headers, Holley Fuel Regulator, March Underdrive Pulleys, Electric Fan, Accel Performance Coil, Accel 300+ Racing Wires, Ram Air, K&N Filter, 79mm Mass Air Unit, FlowMaster Exhaust w/BBK Offroad H-Pipe, Hurst Short Throw Shifter, 3:55 Gears, Ram Clutch, Cross Drilled Rotors, High Tolerant Painted Calipers |
![]() |
![]() |
![]() |
#9 |
Mustang Addict
Join Date: Jan 2001
Location: McKinney, TX
Posts: 1,294
|
![]() If you're talking about the slapper bar type traction bars, I would not recommend them on a street car. I had the Lakewoods on my 87LX (100shot) and they definitely helped traction, but they used to hit the ground alot going over big bumps or uneven surfaces. This eventually resulted in the brake limiter hangers being smashed up against the unibody and not allowing the bars to move like they should.
The lift bars that they make that replace your stock control arms are better for the street, but I still was not that impressed with them on my friend's Cobra. ------------------ 2000GT Atlantic Blue: Cobra R Wheels-17x9 255/40/17, 17x10.5 315/35/17, tubular K-member & control arms, Tokico 5-ways, coil overs, sway bars, strut/shock tower bars, 70mm FMS throttle body, Saleen nose. 79 Pace Car: Maximum Motorsports suspension - H&R Race springs, Bilsteins, rear control arms, chassis bracing, Draglites, 302 w/ Edelbrock Performer intake, cam and 600cfm carb, BBK equal-lengths & H-pipe, 2.5" Flowmaster 2chmbr exhaust, Al Driveshaft, 8.8 trak-loc, TCI C4 w/ 2000 stall, B&M |
![]() |
![]() |
![]() |
#10 |
I need 110mph Trap Speed!
Join Date: Feb 1999
Location: So, CA
Posts: 4,315
|
![]() Get some tires, nothing else is gonna help, I've been in your situation.
Skyler ------------------ -1989 Saleen Mustang #406- TFS Heads, E-303, edelbrock intake,70MM TB, 73mm MAF, off road H, 2 1/4" exhaust, and 4.10's. 332RWHP@5500 351RWTQ@3750 Runs on 87 Octane! |
![]() |
![]() |
![]() |
#11 |
Tires Fear Me...
Join Date: Jan 2001
Posts: 867
|
![]() Does anyone know if i could fit 255's in the back and 245's in the front and it still look ok??
------------------ 347 Stroker Motor: Balanced, 24lb Bosch Injectors, Cobra Computer, Cobra Transmission, Extude Ported and Polished Upper and Lower, GT40 Milled Ported and Polished Heads, B303 Cam, BBK 1 5/8 Headers, Holley Fuel Regulator, March Underdrive Pulleys, Electric Fan, Accel Performance Coil, Accel 300+ Racing Wires, Ram Air, K&N Filter, 79mm Mass Air Unit, FlowMaster Exhaust w/BBK Offroad H-Pipe, Hurst Short Throw Shifter, 3:55 Gears, Ram Clutch, Cross Drilled Rotors, High Tolerant Painted Calipers |
![]() |
![]() |
![]() |
#12 |
Registered Member
Join Date: Mar 2001
Location: Gainsville,Fl
Posts: 229
|
![]() hate to break it to you, but all those mods are useless if you cant get it to the floor. First, those rims should be able to hold a 235 or 245/ 60, next, do you have posi?. Dont skimp on suspension. Save some money. SSM's arent cheap, but they're among the best.. I just finished my suspension. SSM lowers and uppers, welded torque boxes, lakewood 50/50 shocks, 70/30 struts and some heavy duty sway bars front and rear and Eidbach launch kit( springs) Also, what gear ratio are you running?
[This message has been edited by Oldschoolpony (edited 03-22-2001).] |
![]() |
![]() |
![]() |
#13 |
Undescribable
Join Date: Sep 1998
Location: Ft Myers Fla
Posts: 1,539
|
![]() first thing with traction troubles is to make sure u have a good tire on the car before anything else and thet should help somewhat, but qith the torque that 347 is making i would be willing to bet you will need some good suspecions pieces to help also.
B.T.W 2 thing i saw in your mods got my attention. 1. why are you running a cobra computer?? 2. are you running stock 302 intake that has been extrude honed and gt-40 head that are ported and polished?? ------------------ 93-LX: 5 Speed, Flow's with H-Pipe, 3.73's Sub's and K&N. |
![]() |
![]() |
![]() |
#14 |
Registered Member
Join Date: Jan 2001
Location: oklahoma city oklahoma USA
Posts: 9
|
![]() SUBFRAME CONECTORS they do help and if dont have posi get get some and get some good griping tires man if you need to go cheap get some futruas from pep boys they grip like no other and they are cheap
|
![]() |
![]() |
![]() |
#15 |
Registered Member
Join Date: Jan 2001
Location: Virginia
Posts: 118
|
![]() A good combo on tires would be 225/55s up front and 245 or 255/50s out back. If you can afford it, get some Mickey Thompson ET Streets and you will be able to launch at 4000 easy.
------------------ 89 LX Coupe 306, 10:1 compression, Holley Heads, Intake, and Cam package, 70 mm Throttle body and Mass Air, 30 lb injectors, 255 lph fuel pump, 1 5/8" full length headers, Flowmaster 2 1/2" American Thunder Cat back system, Centerforce dual friction clutch, 4.10 gears 50-175 hp Nitrous Works kit, 5" Auto Meter Shift Light |
![]() |
![]() |
![]() |
#16 |
Registered Member
Join Date: Sep 2000
Location: germantown,maryland USA
Posts: 47
|
![]() PEPBOYS! They do work!235/60/15 1.82 60ft with a good posi and 347 c-4, and they cry second gear!
|
![]() |
![]() |
![]() |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
8" traction....what's out there? | 66fastback | Classic Mustangs | 5 | 10-14-2002 12:14 PM |
traction problem - help | Lawless | Windsor Power | 19 | 01-17-2002 10:20 PM |
Traction Control | Kman | Modular Madness | 2 | 06-15-2000 06:31 PM |
Traction Control | Eminent18 | Modular Madness | 5 | 05-22-2000 06:44 PM |