![SEARCH](http://www.mustangworks.com/images/search.png)
![The Mustang Works](http://www.mustangworks.com/images/mw_footer_logo.gif)
© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
![]() |
#1 |
T.P.M. President
Join Date: May 2002
Location: Brownsville
Posts: 265
|
![]() I finally scored a set of gt-40 irons off of a 94 cobra for a great price. I already have the Explorer intakes, and now I have to get started on some home porting and polishing. I do have a few questions.
First, I have an electic drill. Is this the kit that I want to use for the work port/polish bits, or should I get a dremel and a similar kit? If I get a dremel, is the 35,000 rpm variable speed the one I want or can I gat away with a single speed? Second, Is there a definitive guide on home porting/polishing. I already did the search and found some info on cleaning out all the flashing, opening/smoothing out the exhaust port, gasket matching, and not polishing the intake runners because of turbulence needed... Third, did anyone feel like they were about to "screw the pooch" when working on their first port/polish job? I've been putting it off because I'm a little afraid that I'll mess something up, but I don't trust anyone else to work on the stuff. I don't want to just bolt and go to have to come back later to squeeze evey last ounce out of it. Thanks guys.
__________________
![]() |
![]() |
![]() |
![]() |
#2 |
T.P.M. President
Join Date: May 2002
Location: Brownsville
Posts: 265
|
![]()
__________________
![]() |
![]() |
![]() |
![]() |
#3 |
Registered Member
Join Date: Oct 1999
Location: Pierre Part, La. U.S.A.
Posts: 1,850
|
![]() I have ported a few sets. Results were great. I also have a GT-40 iron head, totaly ported and big valves. You want it? The other was trashed in a bad way.
![]()
__________________
88workcar 1988 Mustang LX 342. 417rwhp @ 6800. 28 X 10 ET Drag, 4.30s, 10.69 @ 126.43 1.42 60ft. 11.13 @ 127.7 on BFGs 1.72 60ft Rice Hater # 42 To be old and wise, You must first be young and stupid ![]() |
![]() |
![]() |
![]() |
#4 |
Registered Member
Join Date: Aug 2002
Location: SanAntonio, Tx
Posts: 957
|
![]() The guys at the machine shop told me you cant go real deep on gt-40's cuz of water passages, if i were you i would just clean up the intake side, and cut out a good amount on the exhaust and polish smooth).
my intake was hogged out, carved on the upper inlet, and opened up the lower pretty good, on the lower part of the runners they made a swirl rough polish for turbulence. I would recomend a 3 angle valve job also. |
![]() |
![]() |
![]() |
#5 |
Sober voice of Reason
Join Date: Nov 1998
Location: Kelowna, B.C., Canada
Posts: 1,514
|
![]() Don't mess with the floor of the port and don't mess with the short turn radius, these are the most critical areas to avoid screwing up on. Fox lake found a ton of flow out of my heads and the car dynoed at 288.7 rwhp @6000 and 313 ft/lbs of torque at 3800rpm last friday. This is on a stock 302 short block and with only 8.75:1 compression (damn 65 cc combustion chambers
![]()
__________________
393W: AFR 205's, hydraulic roller, TKO600. |
![]() |
![]() |
![]() |
#6 |
Registered Member
Join Date: Aug 2002
Location: SanAntonio, Tx
Posts: 957
|
![]() red82, i have the same problem with my heads....low compression (good for blower)
![]()
__________________
X-Texas highway patrol ssp 1990 coupe - exploder Gt-40 iron heads, Explorer intake, 19 lber's. E-cam. crane 1.7 rollers. 190fp. 75mm maf. 65mm tb, tubular subframe connectors, mac cai, Asp crank pulley, T-5, king cobra clutch, flowtech 1-5/8 unequals, mac X-pipe Frpp driveshaft, lakewood Lca's. race weight 3,160 12.69 @ 107.35, 1.71 60' 26x8.5 drag's 3.90 gear 13.20 @ 106.91 - 235/60/15 firestones 2.3 60' 3.27 gear |
![]() |
![]() |
![]() |
#7 |
Registered Member
Join Date: Oct 1999
Location: Pierre Part, La. U.S.A.
Posts: 1,850
|
![]() Well the one head I have left is ported quite well, very professional. One of the big badass shops acually ported the ones I have. The car they came off of had a WR1087, and a big hit of spray. It ran 10s.
__________________
88workcar 1988 Mustang LX 342. 417rwhp @ 6800. 28 X 10 ET Drag, 4.30s, 10.69 @ 126.43 1.42 60ft. 11.13 @ 127.7 on BFGs 1.72 60ft Rice Hater # 42 To be old and wise, You must first be young and stupid ![]() |
![]() |
![]() |
![]() |
#8 |
Registered Member
Join Date: Mar 2003
Location: Saint Louis, MO
Posts: 634
|
![]() Don't fret about working on the floor or short side radius - the short side of the head and the intake and lower intake runner roof where it turns into the lower are actually where you'll find some more flow. Just don't get carried away.
I have a bunch of ported intakes out there - stock lower and Cobra style lowers - on Stangnet,Corral,50Tech and maybe one or two from this site. Rather than buy all those rolls, I'd suggest buying a couple of "double cut" carbide burs for both the heads and intake. If you don't use much pressure on the bits the bite soft and don't take a bunch of metal out. Just take your time - you got plenty of that - go to: www.carbidebur.com get one "Flame (SH)" and one "Taper (SL)" bit in a 3/8" diameter. go to www.veryuseful.com/mustang/tech/engine and download my basic instructions on porting an intake. Taking measurements with the tools I recommend will keep you from breaking through of the runners.
__________________
Tom (Torque) Moss 88Gt 5spd Vert, FLowmaster Catbacks, stock cam advanced 4° @ 108.5° ICL, NMRA prepped GT40P heads 1.85/1.55 valves and 1.7 rockers, MAC P headers Jet-Hot coated, 97 Exlporer intake (ported lower), TB and injectors. 277RWHP/330RWTQ (SAE). http://www.fastlanecars.com/ |
![]() |
![]() |
![]() |
#9 |
Sober voice of Reason
Join Date: Nov 1998
Location: Kelowna, B.C., Canada
Posts: 1,514
|
![]() For a rookie, the floor probably isn't too bad, but the short side radius can give you a dead port if you don't understand airflow and take too much out of it
Coupe5oh, I've been playing with the idea of a blow thru turbo or supercharger, was leaning towards the turbo but they are so finicky and it's a lot easier to just buy the paxton kit than to have to fabricate all the turbo plumbing. Oh well, maybe I'll just bottle it.
__________________
393W: AFR 205's, hydraulic roller, TKO600. |
![]() |
![]() |
![]() |
#10 |
Registered Member
Join Date: Mar 2003
Location: Saint Louis, MO
Posts: 634
|
![]() It is usually better to let a pro do porting, but the stocl lower is so ripe for improvement it would be hard to screw up. If you use a good internal snap guage or internal calipers set combined with an exxternal caliper set to keep track of wall thickness and aim to equalize the runner cross section (internal runner size), it's hard to go too wrong - unless you get carried away and do not measure as you go - follow my instructions and you should be OK.
__________________
Tom (Torque) Moss 88Gt 5spd Vert, FLowmaster Catbacks, stock cam advanced 4° @ 108.5° ICL, NMRA prepped GT40P heads 1.85/1.55 valves and 1.7 rockers, MAC P headers Jet-Hot coated, 97 Exlporer intake (ported lower), TB and injectors. 277RWHP/330RWTQ (SAE). http://www.fastlanecars.com/ |
![]() |
![]() |
![]() |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
ran a '01 GT | EZRIDN | Stang Stories | 3 | 08-29-2001 08:17 PM |
GT and LS-1 get into Tangle. GT WINS!! | Mercury | Stang Stories | 8 | 06-26-2001 12:49 PM |
I Lost my first race in my 2000 GT | Mercury | Stang Stories | 10 | 05-27-2001 10:39 PM |
Where can I find GT 40 Irons? | chris91LX | Windsor Power | 1 | 03-12-2001 06:09 PM |
Just got an awesome race w/ a white '91 GT convertible (1-20-01, 11:30 pm) | Fox Body | Stang Stories | 3 | 01-22-2001 09:00 AM |