![SEARCH](http://www.mustangworks.com/images/search.png)
![The Mustang Works](http://www.mustangworks.com/images/mw_footer_logo.gif)
© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
![]() |
#1 |
Registered Member
Join Date: Jul 2001
Location: Seattle, WA
Posts: 381
|
![]() Hey,
Looking to get the following before I finish my T5 installation. Black carpet for front and back. Black carpet for 'trunk' area. Black seat cover for rear seat. Black door panels (for door and lock area). How much should I expect to spend, and who sells this stuff? Tried this post a while back, but got inaccurate responses (err...couldn't find the parts on the supplied sites). Thanks, DoranW
__________________
What I have: 1990 Red Mustang 5.0 LX: [BBK X-Pipe]-[MAC Cat-Back Exhaust] [MAC Cold Air Intake]-[BBK Equal Shorties] [3.55 Gears]-[Cobra Intake Manifold (Upper and Lower] [E-303 Cam]-[Granetelli Mass Air Flow Sensor] [Front and rear sway bars]-[New black carpet and seats.] [Adjustable Fuel Regulator]-[T5 Conversion w/ K. Cobra Clutch/Hurst STS] [Cobra Throttle Body]-[130A Alt. Conversion] Thinking about: Aftermarket Heads! Vortech A-Trim |
![]() |
![]() |
![]() |
#2 |
Registered Member
Join Date: Aug 2001
Location: Huntington NY
Posts: 573
|
![]() new trunk carpet:
http://www.brothersperformance.com/s...g/acc3294.html new interior carpet: http://www.brothersperformance.com/s...g/acc2196.html rear seat covers (cloth): http://www.brothersperformance.com/s.../flofitrc.html rear seats (leather): http://www.brothersperformance.com/s.../flofitrl.html For the door panels, give them a call, they might have them. I was going to do a black cobra conversion on the interior of my 89 stang and found lots of stuff on eBay, including COMPLETE black interiors. Good luck with your search.
__________________
-1993 Mustang, 900rwhp 03-04 cobra based 4v swap, full Griggs setup, project underway -1994 Ranger w/ 427cid windsor (daily beater) check it out! |
![]() |
![]() |
![]() |
#3 |
Registered Member
Join Date: Jul 2001
Location: Seattle, WA
Posts: 381
|
![]() Awesome...this is perfect.
I am going to buy new racing seats, so I didn't want to get the full interior... Thanks, DoranW
__________________
What I have: 1990 Red Mustang 5.0 LX: [BBK X-Pipe]-[MAC Cat-Back Exhaust] [MAC Cold Air Intake]-[BBK Equal Shorties] [3.55 Gears]-[Cobra Intake Manifold (Upper and Lower] [E-303 Cam]-[Granetelli Mass Air Flow Sensor] [Front and rear sway bars]-[New black carpet and seats.] [Adjustable Fuel Regulator]-[T5 Conversion w/ K. Cobra Clutch/Hurst STS] [Cobra Throttle Body]-[130A Alt. Conversion] Thinking about: Aftermarket Heads! Vortech A-Trim |
![]() |
![]() |
![]() |
#4 |
Conservative Individualist
Join Date: May 1997
Location: Wherever I need to be
Posts: 7,487
|
![]() Latemodel Restoration Supply and Texas Mustang Parts sell carpets, upholstery and some plastic interior parts. Worth a shot.
www.50resto.com www.texasmustang.com Other Mustang interior parts suppliers abound; check the Mustang magazine ads and use a search engine to locate more. Last resort for plastic interior parts are the local boneyards. Interiors are similar on the 4 cylinder Mustangs so you have a good chance of finding what you need there, as far as any hard plastoc parts go. |
![]() |
![]() |
![]() |
#5 |
Registered Member
Join Date: Mar 2000
Location: Springfield, Ma, usa
Posts: 706
|
![]() I picked up a black carpet, kick panels, door sills, and sun visors out of a T-boned 4 cyl in my local junkyard. Total price was 40 bucks. Oh yeah and the black seat belts that some how made there way in to my pants. Not a bad way to get parts!
__________________
NewEngland Auto www.baystategearheads.com -91 Mustang Coupe, ex 4cyl (sold) -99 F150, 3" lift, 35" Procomps, Magnaflow exhaust |
![]() |
![]() |
![]() |
#6 |
Don Corlione
Join Date: Jun 2001
Location: Omaha NE USA
Posts: 491
|
![]() Black door panels are a hot commodity in eBay. Expect to pay around $200 for them. Good Luck.
__________________
Eric - 89 Mustang LX coupe 5 speed 302-Cobra Intake-GT40p heads-TFS stage 1 cam-FRPP 1.6 roller rockers-3:73 gears-KYB shocks and struts-Eibach Pro-kit-HPM Mega-bite upper and lower control arms-FRPP aluminum driveshaft-16x8 Chrome Cobra Rs R.H.C. #14 |
![]() |
![]() |
![]() |
#7 |
Registered Member
Join Date: Aug 2001
Location: Huntington NY
Posts: 573
|
![]() If anyone is interested in black interior panels, there are lots of them real cheap on eBay now.
__________________
-1993 Mustang, 900rwhp 03-04 cobra based 4v swap, full Griggs setup, project underway -1994 Ranger w/ 427cid windsor (daily beater) check it out! |
![]() |
![]() |
![]() |
#8 |
Procharged!
Join Date: May 1999
Location: Hanover, PA
Posts: 1,539
|
![]() Well I bought my black carpet through Summit, ACC was the brand I went with and it fits and looks great, you can also buy the hatch piece. I just finished converting my grey interior to black and it looks better the factory, I used the Duplicolor Vinyl and Interior paint $3.50/can at Walmart.
I was always afraid to do this but if you prep it right it will not scratch or rub off, I wiped all my parts down with Mr.Clean/Hot Water and dried then, then scuffed the panels lightly with a Red Sciff pad (Body shop supply house sell these, you could also use White which is less aggressive) then I wiped them down with Grease and Wax remover and painted them Matte Black, took 5 cans to do all my plastic, door panels and dash. I'll have to get some pics, I just finshed putting the new headliner and rear carpet (no rear seat) in last night and it looks AWESOME!
__________________
D/R 10108 NMRA Drag Radial, 25.5 chassis, F1R Check out RNH Performance Performance Engines and Custom Fabrication. From Mild to Wild we can build what you want, when you want it. FOR SALE Stainless Steel Torque Box Supports |
![]() |
![]() |
![]() |
#9 |
Registered Member
Join Date: Mar 2000
Location: Springfield, Ma, usa
Posts: 706
|
![]() Watch out for that Duplicolor crap!!! That's what I used at first, and it looked great. After a while it started to fad and chip. especially on the door sills where my feet would drag across, and the pads on the arm rests. I even took all the steps to degrease, clean, and scuff the surfaces too. I found out about a company called SEM products. Their paint in far superior then Duplicolor, by a long shot!!!!! It costs a little more about 8 bucks a can, but totally worth it. I haven't had any problems with the paint since then! Just and FYI
__________________
NewEngland Auto www.baystategearheads.com -91 Mustang Coupe, ex 4cyl (sold) -99 F150, 3" lift, 35" Procomps, Magnaflow exhaust |
![]() |
![]() |
![]() |
#10 |
Registered Member
Join Date: Aug 2001
Location: Huntington NY
Posts: 573
|
![]() DON'T BUY PAINT!! What you really need is interior dye in a spray can. Its about $3 a can and will dye the plastic so it won't rub off.
__________________
-1993 Mustang, 900rwhp 03-04 cobra based 4v swap, full Griggs setup, project underway -1994 Ranger w/ 427cid windsor (daily beater) check it out! |
![]() |
![]() |
![]() |
#11 |
I'd rather be basketweaving
Join Date: Feb 2000
Location: Indianapolis
Posts: 2,551
|
![]() Hey Rick, hows the car coming along? I havent seen any pics since you first started the painting.
__________________
NMRA O/C 9516 NA pumpgas stickshift 347 10.65@125.6, 6.73@100, 1.41 60ft |
![]() |
![]() |
![]() |
#12 |
Procharged!
Join Date: May 1999
Location: Hanover, PA
Posts: 1,539
|
![]() Well so far my pieces look great and even when I scraped them I can't get any to come off, I agree the SEM paint is great I have used that on all my metal interior and exterior trim, worth the money if you can find it local or Eastwoods carries it.. I think one thing that helped mine is it hasn't seen any kind of armor oil or dressing in over a year, and I made sure I throughly cleaned it. Since my car is retired to a garage queen, weekend cruise/racer it should be fine, I have even scratched it with a screw driver and it hasn't come off...maybe I just got lucky.
fiveohpatrol- Check out my new site in my sig, it has pic's of the car. If anyone is going to the All Ford Nats in Maple Grove I'll be there showing on Sunday.
__________________
D/R 10108 NMRA Drag Radial, 25.5 chassis, F1R Check out RNH Performance Performance Engines and Custom Fabrication. From Mild to Wild we can build what you want, when you want it. FOR SALE Stainless Steel Torque Box Supports |
![]() |
![]() |
![]() |
#13 |
Registered Member
Join Date: Aug 2001
Location: Huntington NY
Posts: 573
|
![]() Your "check out my site" link is not working.
__________________
-1993 Mustang, 900rwhp 03-04 cobra based 4v swap, full Griggs setup, project underway -1994 Ranger w/ 427cid windsor (daily beater) check it out! |
![]() |
![]() |
![]() |
#14 |
Procharged!
Join Date: May 1999
Location: Hanover, PA
Posts: 1,539
|
![]()
__________________
D/R 10108 NMRA Drag Radial, 25.5 chassis, F1R Check out RNH Performance Performance Engines and Custom Fabrication. From Mild to Wild we can build what you want, when you want it. FOR SALE Stainless Steel Torque Box Supports |
![]() |
![]() |
![]() |
#15 |
Registered Member
Join Date: Aug 2001
Location: Huntington NY
Posts: 573
|
![]() Can you post some pics close up of that air filter cover. I need to make one for my car and need some ideas. If you don't have any pics, can you explain what you did? If you bought it, where?
__________________
-1993 Mustang, 900rwhp 03-04 cobra based 4v swap, full Griggs setup, project underway -1994 Ranger w/ 427cid windsor (daily beater) check it out! |
![]() |
![]() |
![]() |
#16 | |
Procharged!
Join Date: May 1999
Location: Hanover, PA
Posts: 1,539
|
![]() Quote:
__________________
D/R 10108 NMRA Drag Radial, 25.5 chassis, F1R Check out RNH Performance Performance Engines and Custom Fabrication. From Mild to Wild we can build what you want, when you want it. FOR SALE Stainless Steel Torque Box Supports |
|
![]() |
![]() |
![]() |
#17 | |
Yay for Chickys
Join Date: Feb 2001
Posts: 1,532
|
![]() Quote:
![]() |
|
![]() |
![]() |
![]() |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
99GT vs. 2000 Lightning | wantapony2001 | Stang Stories | 52 | 01-04-2003 06:30 PM |
Will a Black Magic Fan cool a 331? | 302 LX Eric | Windsor Power | 12 | 08-29-2002 07:52 AM |
Wheel wells aren't black | Stang_Crazy | Appearance & Detailing | 6 | 07-03-2002 08:41 PM |
Black on Black GT wanted! | Zero596@gte.net | Modular Madness | 0 | 05-08-2001 11:54 PM |