![SEARCH](http://www.mustangworks.com/images/search.png)
![The Mustang Works](http://www.mustangworks.com/images/mw_footer_logo.gif)
© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
![]() |
#1 |
Registered Member
Join Date: May 2002
Location: Nebraska
Posts: 63
|
![]() I need help locating the following parts for a 2003 Cobra.
Any links you can send me or post would be greatly appreciated. 1. Blower pulley 2. Catback Exhaust system (not steeda) 3. H pipe 4. Cold Air Intake setup 5. Performance chip 6. Drag Radials (current tires are 275/40zr17) Also i was wondering how the steeda exhaust systems compare to others like Flowmaster and MAC as far as horsepower and sound.What are the effects of using an offroad H pipe without Convertors or potential problems? My Email is RedCobra@cox.net |
![]() |
![]() |
![]() |
#2 |
Registered Member
Join Date: Apr 2002
Location: Downers Grove, IL
Posts: 464
|
![]() 1. try using a SVT Lightning pulley
4. http://www.uprproducts.com/shopping/shopexd.asp?id=371 If you don't run cats, you will get better performance and a louder, deeper sounding exhaust. Only thing is you can't pass emissions.
__________________
1989 Black Mustang GT Hatchback, Underdrive Pulles, Electric Fan, Cold Air Intake, Headers, Offroad H-Pipe, Magnaflow catback, Steeda Tri-Ax, Fluidyne Aluminum Radiator, Timing at 14*, 3.73's Coming not so soon: 408w Ricer Hater's Club Member #59 |
![]() |
![]() |
![]() |
#3 |
Registered Member
Join Date: May 2002
Location: Nebraska
Posts: 63
|
![]() problem with using the lightning pulley is theres no way of knowing what your final boost figure is going to be.
I dont wanna spend 200 bucks on a pulley and then blow the heads off my engine. |
![]() |
![]() |
![]() |
#4 |
Registered Member
Join Date: Apr 2002
Location: Downers Grove, IL
Posts: 464
|
![]() Try these guys then, http://www.southfloridapulleyhq.com
__________________
1989 Black Mustang GT Hatchback, Underdrive Pulles, Electric Fan, Cold Air Intake, Headers, Offroad H-Pipe, Magnaflow catback, Steeda Tri-Ax, Fluidyne Aluminum Radiator, Timing at 14*, 3.73's Coming not so soon: 408w Ricer Hater's Club Member #59 |
![]() |
![]() |
![]() |
#5 |
Registered Member
Join Date: May 1999
Location: moorpark ca
Posts: 340
|
![]() i just installed the south florida pulley system on my car and wow it pulls much harder now! I'm going to try and get a dyno tune this friday! it feels like a 75 shot of nos!! i really doubt you'll blow the heads off a motor with 8.5 to 1 compression but the cool thing about the south florida pulley system is you can get different size pullies! so if you don't want too much boost no problem just pick a bigger pulley
![]() ![]() Leon
__________________
03 sonic blue cobra coupe, 11.49@122mph bakerfield raceway! 11.67@120mph fontana 98 GT, stock for now. |
![]() |
![]() |
![]() |
#6 |
Registered Member
Join Date: May 2002
Location: Nebraska
Posts: 63
|
![]() what tool did you use to remove the old pulley and then install the new one?
How much total boost are you getting from the pulley you bought? |
![]() |
![]() |
![]() |
#7 |
Registered Member
Join Date: May 1999
Location: moorpark ca
Posts: 340
|
![]() i had a puller at my work. it is similar to the one on south florida pulleys website. they sell the tool as well!! it's actually a pretty easy swap. my stock guage gets buried past the 10lb mark. i need to get an aftermarket guage for it! most of the guys i've talked to are getting 12-12.5lbs total boost. If your worried just get one of the bigger pullies for the street and then when you go to the track you could put a smaller one on! the cool thing is that pullies are easily swapable with there system!check out this site:
svtperformance.com lots of good info on our cars there ![]() ![]() Leon
__________________
03 sonic blue cobra coupe, 11.49@122mph bakerfield raceway! 11.67@120mph fontana 98 GT, stock for now. |
![]() |
![]() |
![]() |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
2003 Cobra Buyer Beware!! | Doug McGinn | Modular Madness | 16 | 07-25-2002 08:26 AM |
2003 Cobra Parts | Doug McGinn | Modular Madness | 6 | 07-16-2002 06:23 PM |
Buddy Just Bought a 98 Cobra..... | INVINCISTANG | Stang Stories | 10 | 06-25-2002 01:36 PM |
What's the difference between 95 GT and 95 Cobra? | Ron Brooks | Blue Oval Lounge | 5 | 07-13-2001 12:56 PM |
Cobra Computer | Bangin Gears | Windsor Power | 1 | 04-30-2001 02:38 AM |