MustangWorks.com - The Ford Mustang Power Source!

Go Back   MustangWorks.com : Ford Forums > Mustang & Ford Tech > Modular Madness
Register FAQ Members List Calendar

Notices


Reply
 
Thread Tools Rate Thread Display Modes
Old 04-16-2006, 06:51 PM   #1
mark sweetser
96GREENGT
 
Join Date: Mar 2005
Location: las vegas
Posts: 51
Default vibration at 3k

just got a centerforce dual friction clutch kit installed. at same time, swapped to a new centerforce throw-out bearing, and a new pilot bearing supplied by the shop were i had install done. problem is, at 3,000 RPM in any gear, there is a bad vibration that rattles the whole car. wasn't there prior to clutch swap, even after swap to 3.73 gears. i still have 200 miles or so to go on the 450-500 mile break-in period recommended by centerforce on clutch. when the rattle comes on, the car seems to lose some steam. will this clear up after 200 or so miles, once the clutch is broken in and set correctly? i have been going fairly easy on the gas during the break-in (no WOT).
__________________
-'96 GTS Deep Forest Green Metallic- 8#Powerdyne,Bassani Cat-X,2 chamber Flows, FMS alum. DS,Kenne Brown subframes,Pro 5.0 short throw,FRPP 3.73's,Accufab Plenum/75mm TB,11# blower pulley,Bassani mid headers,Eibach 1.5" springs,17" Cobra R's w/ 275/40zr-17 g-force kd's,Centerforce Dual Friction
-'87 Black LX 5.0
BBK shorties&Cat-X,2 chamber Flows,MSD ign,stock 3.08's,MGW short-throw,BBK cold-air,King Cobra clutch,235/55-17(F)&255/50-17(R) Kumho Ecsta's on 95 Cobra R 4-lugs
mark sweetser is offline   Reply With Quote
Old 04-16-2006, 10:00 PM   #2
Hammer
AKA "Dr. Evil"
 
Hammer's Avatar
 
Join Date: Feb 1999
Location: South Fork Ranch
Posts: 1,721
Default Re: vibration at 3k

Sounds like the clutch may not be dis-engaging all the way....
__________________
Uncle Sam
"What the hell is up with all the gauges?
Calling Captain Kirk, your ride awaits... Phasers on stun...."
Hammer is offline   Reply With Quote
Old 04-19-2006, 09:53 PM   #3
mark sweetser
96GREENGT
 
Join Date: Mar 2005
Location: las vegas
Posts: 51
Default Re: vibration at 3k

thanks for the response...what would the fix be for that? is clutch defective? wrong one? installed incorrectly? thanks hammer!
__________________
-'96 GTS Deep Forest Green Metallic- 8#Powerdyne,Bassani Cat-X,2 chamber Flows, FMS alum. DS,Kenne Brown subframes,Pro 5.0 short throw,FRPP 3.73's,Accufab Plenum/75mm TB,11# blower pulley,Bassani mid headers,Eibach 1.5" springs,17" Cobra R's w/ 275/40zr-17 g-force kd's,Centerforce Dual Friction
-'87 Black LX 5.0
BBK shorties&Cat-X,2 chamber Flows,MSD ign,stock 3.08's,MGW short-throw,BBK cold-air,King Cobra clutch,235/55-17(F)&255/50-17(R) Kumho Ecsta's on 95 Cobra R 4-lugs
mark sweetser is offline   Reply With Quote
Old 04-20-2006, 08:29 AM   #4
1989GT
Registered Member
 
1989GT's Avatar
 
Join Date: Apr 1999
Location: Cincinnati,OH
Posts: 1,511
Default Re: vibration at 3k

Does it only happen when moving? Try putting the tranny in neutral then rev to 3k see if the vibration is there, then put the clutch in and rev to 3k see if it's there. Let us know.
__________________
89GT,Pro-Bullet 306, H/C/I and a bunch of other stuff. *Sold*

00GT, Vortech S-Trim, Steeda Boost Pipe, C&L intake, Mac off-road H-pipe, Flowmasters, B&M Ripper shifter, Eibach Sportline springs, Koni Struts/shocks, MM full length subframe connectors, Cobra brakes, 3.73's.
My Car Domain Page
1989GT is offline   Reply With Quote
Old 04-20-2006, 08:57 PM   #5
mark sweetser
96GREENGT
 
Join Date: Mar 2005
Location: las vegas
Posts: 51
Default Re: vibration at 3k

thanks for the idea, i should have thought of that. NO, it does not vibrate at all when car is in neutral and not in motion...rules out flywheel, right? i did have it re-surfaced on clutch install. noticed today on way home: had my left foot covering clutch after i let pedal out, and when i applied throttle, clutch sprung back up and contacted my foot. what's up?
__________________
-'96 GTS Deep Forest Green Metallic- 8#Powerdyne,Bassani Cat-X,2 chamber Flows, FMS alum. DS,Kenne Brown subframes,Pro 5.0 short throw,FRPP 3.73's,Accufab Plenum/75mm TB,11# blower pulley,Bassani mid headers,Eibach 1.5" springs,17" Cobra R's w/ 275/40zr-17 g-force kd's,Centerforce Dual Friction
-'87 Black LX 5.0
BBK shorties&Cat-X,2 chamber Flows,MSD ign,stock 3.08's,MGW short-throw,BBK cold-air,King Cobra clutch,235/55-17(F)&255/50-17(R) Kumho Ecsta's on 95 Cobra R 4-lugs
mark sweetser is offline   Reply With Quote
Old 04-20-2006, 09:15 PM   #6
Hammer
AKA "Dr. Evil"
 
Hammer's Avatar
 
Join Date: Feb 1999
Location: South Fork Ranch
Posts: 1,721
Default Re: vibration at 3k

Quote:
had my left foot covering clutch after i let pedal out, and when i applied throttle, clutch sprung back up and contacted my foot. what's up?
Hmmm.... I would say that there is probably a problem between your flywheel and clutch disk. Are you sure you used the correct throw-out bearing for your application?
__________________
Uncle Sam
"What the hell is up with all the gauges?
Calling Captain Kirk, your ride awaits... Phasers on stun...."
Hammer is offline   Reply With Quote
Old 04-21-2006, 10:52 AM   #7
1989GT
Registered Member
 
1989GT's Avatar
 
Join Date: Apr 1999
Location: Cincinnati,OH
Posts: 1,511
Default Re: vibration at 3k

Do you have an adjustable cable and quadrant? If so I would play around with it to see if the clutch is adjusted right, since the vibration only occurs when the car is in motion I'm leaning more towards the driveshaft. Reving in neutral(clutch pedal out) would rule out the clutch/pressure plate/flywheel and input shaft on the tranny. I would disconnect the drive shaft and rotate it over a hole and hook it back up and see if the vibration is there/get's better or worse. Do that all the way around until it either stops or you're back at the starting point. I would say though that it could also be the clutch is not adjusted right and could just be manifesting itself while in motion at 3k RPM.
__________________
89GT,Pro-Bullet 306, H/C/I and a bunch of other stuff. *Sold*

00GT, Vortech S-Trim, Steeda Boost Pipe, C&L intake, Mac off-road H-pipe, Flowmasters, B&M Ripper shifter, Eibach Sportline springs, Koni Struts/shocks, MM full length subframe connectors, Cobra brakes, 3.73's.
My Car Domain Page
1989GT is offline   Reply With Quote
Reply



Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
follow up to horrible vibration problem Toeclicker Windsor Power 4 12-18-2003 06:38 PM
rear end vibration stang_guy_95 Windsor Power 4 12-17-2003 04:53 PM
Vibration Problem RDMumfts Stang Windsor Power 10 03-23-2003 07:04 PM
Something bad is about to happen to my car - vibration from somewhere 2FastLX Windsor Power 6 08-20-2001 09:27 AM
Vibration thru vehicle when accelerator is pressed race1now Windsor Power 1 01-22-2001 12:28 AM


All times are GMT -5. The time now is 05:54 PM.


SEARCH