![SEARCH](http://www.mustangworks.com/images/search.png)
![The Mustang Works](http://www.mustangworks.com/images/mw_footer_logo.gif)
© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
![]() |
#1 |
Registered Member
Join Date: Nov 2000
Posts: 290
|
![]() The transmission to radiator lines on my 68 coupe (C4 transmission) are badly bent and not routed properly. As a result, when I turn the steering wheel to the left the power steering cylinder is hitting one of the lines. I bought a brand new set but here's my problem - can't get them loose from the transmission. Easy to unscrew from the radiator, but how in the heck do you get a wrench in those tight spaces to undo the fittings. I don't have line wrenches but can easily buy, but don't know if they'll do me any good since I can't figure out how to get the wrench on other than at an angle. Would be easy if I dropped the transmission, but that's not an option for me in my garage. Anybody know of any tricks or special wrenches to get those fittings loose?
|
![]() |
![]() |
![]() |
#2 |
Registered Member
Join Date: Mar 2001
Location: Southern Maryland
Posts: 471
|
![]() Have you considered just cutting out the damaged portion and replacing that part? Join the old line to the new with brass unions.
Many trans shops just cut the lines when they remove the unit, and when it's put back, they use unions.
__________________
'89 LX 5.0 - 5 speed. Original Owner '94 E-150 4.9 Hi-Top Conversion Van '06 Mustang V-6, 5 speed |
![]() |
![]() |
![]() |
#3 |
Registered Member
Join Date: Jan 2001
Location: Clayton, CA USA
Posts: 116
|
![]() I installed new trans to radiator lines on my C4 and it was a real pain. I did manage to get to the nuts on the trans using crows feet on a 3/8" drive socket.
I seriously concidered the cutting approach but could bring myself to hack up the new lines. However, another hour and a few more busted knuckles and out comes the hacksaw.
__________________
'68 convert, 5.0 GT-40 Crate motor, C-4, Tri-Y headers, 3.25 rear gears |
![]() |
![]() |
![]() |
#4 |
Registered Member
Join Date: Nov 2000
Posts: 290
|
![]() Went to Sears yesterday and bought a set up consisting of a crow's foot, extension, and swivel connector. Was able to get one undone but the crow's foot is just rounding off the other one. If I could find a crow's foot made like a line wrench, pretty sure I could get it off. Just can't bring myself (yet) to cut the new lines. Other problem I discovered when I took the one loose is the ends of the fittings don't match what I have. The new lines came with the ends flared, but my old ones (where they hook to the radiator) have a rounded-type flare about an inch from the end. Don't know why they're different when the lines are nearly identical in shape and length. Excuse my ignorance, but if I do cut the lines, would I not need to the get the cut ends flared? Never used a union, but is it basically a connector for the 2 ends?
|
![]() |
![]() |
![]() |
#5 |
Registered Member
Join Date: Sep 1998
Location: Oviedo, FL
Posts: 992
|
![]() I got tired of the route problems with headers. So I did mine with braided SS hose. Works great.
__________________
"Support our Troops" Dave 1968 Cougar 2004 Thunderbird 2007 F150 Harley-Davidson, SuperCrew 1986 LTD 1997 Ranger 1992 Honda Civic |
![]() |
![]() |
![]() |
#6 |
Registered Member
Join Date: Nov 2000
Posts: 290
|
![]() Well yesterday was my lucky day. Decided on one final attempt and found one large adjustable wrench I had barely fit in the opening. After applying a death grip and turning with all the muscle I had, it broke loose. Replaced both lines and found the correct radiator to transmission line fittings at ACE hardware. Everything installed perfect with no leaks. Only problem I had was I had to remove the engine crossmember support (or whatever you call the curved large bar running under the engine) and when I went to re-install it hit the lines. Had to slightly bend tubes and they're still pretty tight resting against the bar but shouldn't cause me any problems. It won't be driven that much and it's so tight shouldn't be any vibration. Guess no repro part is exactly perfect. Now to next project - trunk lid. Decided to keep repro lid (even though it's not a perfect fit was best I could find and better than my rusted out, unrepairable original) since I was able to very slightly bend certain areas to get a pretty good fit and alignment (give it a 8.5 on a scale of 1-10). Now I've got to measure, make a template of some sort and drill the holes for the chrome molding. Am using stick on "MUSTANG" letters rather than even attempt to drill 14 perfect holes for the push-in letters. Sure wish it had come pre-drilled. Wish me luck.
|
![]() |
![]() |
![]() |
#7 |
Registered Member
Join Date: Mar 2001
Location: Southern Maryland
Posts: 471
|
![]() Kisner --
You don't want the new lines to rub anyplace, cause it won't take long to rub thru. I think the new lines are 3/8" OD. Go get some 3/8 ID fuel or vacuum line, cut to length where rubbing, split it lengthwise and slip over trans line. This will prevent steel line from wearing thru.
__________________
'89 LX 5.0 - 5 speed. Original Owner '94 E-150 4.9 Hi-Top Conversion Van '06 Mustang V-6, 5 speed |
![]() |
![]() |
![]() |
#8 |
Registered Member
Join Date: Nov 2000
Posts: 290
|
![]() Awesome idea - never thought of that. Think I have some extra laying around already. Will do that this weekend. Thanks.
|
![]() |
![]() |
![]() |
#9 |
Registered Member
Join Date: Dec 2001
Location: Brooklyn , New York
Posts: 45
|
![]() hey guys i have a extra trunk lid from a 65 coupe {original} i know that would fit 64-66 so if anyone needs it let me know it is in great shape..
|
![]() |
![]() |
![]() |
#10 |
Registered Member
Join Date: Sep 1998
Location: Oviedo, FL
Posts: 992
|
![]() On drilling the holes to install trim. Why don't you put 2" tape where the trim goes. Mark the hole locations on it. Then you can trial fit before drilling holes. Then just drill where you have the tape marked for the fastners.
__________________
"Support our Troops" Dave 1968 Cougar 2004 Thunderbird 2007 F150 Harley-Davidson, SuperCrew 1986 LTD 1997 Ranger 1992 Honda Civic |
![]() |
![]() |
![]() |
#11 |
Registered Member
Join Date: Nov 2000
Posts: 290
|
![]() Got trunk lid molding holes drilled and everything lines up perfectly. Probably wasn't the best method but taped together 5 pieces of bond paper and marked holes from old lid. Measured and re-measured holes from bottom of lid and drilled away. Fortunately, the holes only have to be perfect from the bottom up since the bolts slide left to right.
|
![]() |
![]() |
![]() |
#12 |
Registered Member
Join Date: Sep 1998
Location: Oviedo, FL
Posts: 992
|
![]() Sounds like a good method to me.
And it worked too. What more could you ask for.
__________________
"Support our Troops" Dave 1968 Cougar 2004 Thunderbird 2007 F150 Harley-Davidson, SuperCrew 1986 LTD 1997 Ranger 1992 Honda Civic |
![]() |
![]() |
![]() |
#13 |
Registered Member
Join Date: Nov 1998
Location: Houston, Tx.
Posts: 3,887
|
![]() I think what I did regarding the transmission lines, was to unbolt the trans mount, remove the trans mount crossmember , disconnect the shift linkage and lower the transmission a few inches using a floor jack. That allowed me adequate access to transmission lines to disconnect them. After reinstalling new lines , the trans was jacked back up and everything was reinstalled. It's been a few years, but that's how I remember it.
Rev
__________________
'66 Coupe, 306, 350-375 HP, C-4, 13.07 e.t., 104.8 mph, 1/4 mi. O.B.C. #2 '66 coupe Last edited by Rev; 05-19-2002 at 03:21 PM.. |
![]() |
![]() |
![]() |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
Speedometer Cable to Transmission O-ring | Kisner | Classic Mustangs | 3 | 07-06-2004 02:13 PM |
Transmission Identification | danmnvik | Classic Mustangs | 2 | 06-10-2003 11:38 AM |
93 5.0 LX A4LD transmission problems | batman9350 | Small Ponies | 0 | 06-09-2003 12:26 PM |
2003 Cobra Transmission | Silver Cobra | Modular Madness | 2 | 08-30-2002 11:39 PM |