![SEARCH](http://www.mustangworks.com/images/search.png)
![The Mustang Works](http://www.mustangworks.com/images/mw_footer_logo.gif)
© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
![]() |
#1 |
Registered Member
Join Date: May 2001
Location: Oklahoma City OK USA
Posts: 236
|
![]() any help fellas?
__________________
90 GT 25th Anni. Did the AOD to T-5 swap, SPEC clutch, Steeda Tri-Ax shifter, BBK 2½ inch off-road H pipe, Flows, BBK 70mm TB/EGR, Ford Racing aluminim driveshaft, 3.55's, welded subframes, Ram Air, 3 core radiator, NOS dry kit 75 shot, and a K&N filter. 12.9 @ 108 |
![]() |
![]() |
![]() |
#2 |
Junior Member
Join Date: Mar 1999
Location: Ventura, California
Posts: 8,981
|
![]() 1) Disconnect the negative battery cable.
2) Turn the headlight switch on. 3) Wait 10 minutes. 4) Turn the headlight switch off. 5) Reconnect the battery cable. Your ECM is now reset. Take care, ~Chris
__________________
Webmaster: Rice Haters Club Jim Porter Racing Peckerwoods Pit Stop Support Your Local
RED & WHITE! |
![]() |
![]() |
![]() |
#3 |
Registered Member
Join Date: May 2001
Location: Oklahoma City OK USA
Posts: 236
|
![]() thats all i have to do if im setting my idle and tps
__________________
90 GT 25th Anni. Did the AOD to T-5 swap, SPEC clutch, Steeda Tri-Ax shifter, BBK 2½ inch off-road H pipe, Flows, BBK 70mm TB/EGR, Ford Racing aluminim driveshaft, 3.55's, welded subframes, Ram Air, 3 core radiator, NOS dry kit 75 shot, and a K&N filter. 12.9 @ 108 |
![]() |
![]() |
![]() |
#4 |
Junior Member
Join Date: Mar 1999
Location: Ventura, California
Posts: 8,981
|
![]() After you finish setting them, you then reset your ECM. You should also do the following relearn procedure:
After resetting the ECM, 1) Start the engine, and allow it to idle for 1 minute. 2) Shut it off, and wait 10 seconds. 3) Start the engine, and turn on the headlights on high, and your a/c, with the fan on high, and let it idle for 1 minute. 4) Turn all the accessories off, and turn the engine off, and wait 10 seconds. 5) Start the engine, and make it idle @ 2000 rpm for 1 minute. 6) Shut it off, and wait 10 seconds. 7) Start the engine, and turn on the headlights on high, and your a/c, with the fan on high, and make it idle @ 2000 rpm for 1 minute. 8) Turn all the accessories off, and turn the engine off, and wait 10 seconds. This is the best way to relearn the ECM, but you should take a 10 minute test drive afterwards to make sure all is well. Take care, ~Chris
__________________
Webmaster: Rice Haters Club Jim Porter Racing Peckerwoods Pit Stop Support Your Local
RED & WHITE! |
![]() |
![]() |
![]() |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
how do u reset or clear the computer | whytry89 | Windsor Power | 1 | 03-11-2004 04:30 PM |
Reset Computer in 96 Mustang GT? | 9646GT | Modular Madness | 9 | 06-15-2003 10:13 AM |
Trying to put A9L EEC from 90gt into 94gt | manycars23 | Windsor Power | 0 | 07-08-2002 01:45 AM |
A9L Computer | nextime | Windsor Power | 14 | 03-27-2002 10:36 PM |
What are the steps to reset your computer? | 95 King GT | Windsor Power | 7 | 07-10-2001 12:48 AM |