© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
07-17-2002, 03:06 PM | #1 |
Registered Member
Join Date: Feb 2002
Location: from St Louis but in Texas
Posts: 24
|
check engine light
Do anyone know how to reset or turn or the check engine light. I was changing out the hose on my heater core and had to take a bracket a loose. The bracket was connected to one of the header bolts in the process of take the bolt off I cracked the spark plug with the rachet. I did not know that until i was going down the road and the light came on. I pulled over and checked everything that I took aloose and found out the spark plug was cracked. REplaced the spark plugs and light is still on. Need help turning the light off.
|
07-17-2002, 03:19 PM | #2 |
Junior Member
Join Date: Mar 1999
Location: Ventura, California
Posts: 8,981
|
Disconnect the negative battery cable, THEN turn on the headlight switch for ten minutes. Turn the switch off, and reconnect the battery. If the MIL comes back on, you have other issues, and need to have the codes pulled.
Take care, -Chris
__________________
Webmaster: Rice Haters Club Jim Porter Racing Peckerwoods Pit Stop Support Your Local
RED & WHITE! |
07-17-2002, 03:26 PM | #3 |
2 Stangs in the Stable
Join Date: Apr 2002
Location: Baytown, TX
Posts: 1,209
|
While were on the subject of the check engine light, if the o2 sensors are bad on a 90 gt, will that throw on the light?
|
07-17-2002, 03:46 PM | #4 |
Registered Member
Join Date: Feb 2002
Location: from St Louis but in Texas
Posts: 24
|
thank you
PKRWUD it worked out great thank you. Hope to learn more while I'm here on this site.
|
07-17-2002, 05:08 PM | #5 |
Junior Member
Join Date: Mar 1999
Location: Ventura, California
Posts: 8,981
|
bigred-
Yes. LetsGo- My pleasure. Take care, -Chris
__________________
Webmaster: Rice Haters Club Jim Porter Racing Peckerwoods Pit Stop Support Your Local
RED & WHITE! |
07-17-2002, 09:35 PM | #6 |
Registered Member
Join Date: May 2000
Location: Kamloops, BC
Posts: 2,875
|
Isn't the way to reset the computer to turn off but to remove codes is to remove the jumper wire after you start to do a EEC test?
|
07-18-2002, 12:02 AM | #7 |
Junior Member
Join Date: Mar 1999
Location: Ventura, California
Posts: 8,981
|
You can also touch the pos. and neg. battery cables together, but it's not recommended.
Take care, -Chris
__________________
Webmaster: Rice Haters Club Jim Porter Racing Peckerwoods Pit Stop Support Your Local
RED & WHITE! |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
check engine light | bubbalink | Windsor Power | 3 | 07-30-2004 03:44 PM |
Check engine light on a 2000 GT | GITY UUP | Modular Madness | 11 | 04-30-2002 10:16 AM |
New Guy w/ Check Engine light? | Stang_ROTY | Modular Madness | 7 | 06-18-2001 11:34 AM |
Turning Off "Check Engine" Light | King Snake | Modular Madness | 3 | 04-01-2001 07:18 PM |
Check Engine Light? | Maxi 5.0 | Windsor Power | 3 | 01-09-2001 10:50 PM |