Linear Mode
© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
12-21-2004, 04:45 PM
|
#1 |
|
Registered Member
Join Date: Apr 2001
Location: Gallatin, Tn
Posts: 1,326
|
Pilot Bearing
Someone mentioned it was "ok" if you didn't use one. Recommendations gents? Thanks
__________________
|
|
|
|
12-21-2004, 05:21 PM
|
#2 |
|
Registered Member
Join Date: Jul 2003
Location: alberta canada
Posts: 108
|
Re: Pilot Bearing
I would say yes use one, when ya twist that engine I bet the disc moves the input shaft if it was a 4 clyinder maybe, think of a disc gettin 300hp turning between a bearing on each end.
|
|
|
|
|
12-21-2004, 06:32 PM
|
#3 |
|
Domestic Rice really sucks!
Join Date: Apr 2002
Location: KY
Posts: 973
|
Re: Pilot Bearing
You'll be getting a new tranny if you don't.
__________________
The sig says it all. 
|
|
|
|
|
12-21-2004, 10:40 PM
|
#4 |
|
Registered Member
Join Date: May 2002
Location: Tampa,FLORIDA
Posts: 340
|
Re: Pilot Bearing
is it worth the 15 bucks to find out?
__________________
5.0, Holley heads, 1.7 Scorp Rockers, Stealth intake, Holley 600 carb, Holley Mech. Fuel pump, MSD 6Digital, MSD distributor, Hotchkis upper/lower rear control arms, FMS B Springs, 3:73 (8.8) rear. Production # 9,377 |
|
|
|
|
12-29-2004, 01:47 AM
|
#5 |
|
Registered Member
Join Date: Dec 2004
Location: Douglasville, Ga.
Posts: 4
|
Re: Pilot Bearing
You cannot run a manual transmission without one.
__________________
1987 Saleen #0197 restored. Dyno Sheet Saleen/Vortech intake lower ported. Edelbrock heads, Cobra 1.7RR, B303 cam, mac 1 5/8 shorties unequals offroad H pipe, 2chamber flowmasters, Pro M-80 maf, MAC 70TB, 38# inj. Vortech S-trim. 3.12" and 6.87" pulleys, Unlimted Performance PowerPipe. FRPP harmonic Balancer and spacer. Tremec TKO and SPEC stage 4 clutch, Steeda Tri-Ax shifter. 508.2rwhp / 465rwtq SAE corrected, with 14# of boost. |
|
|
|
|
12-29-2004, 09:13 AM
|
#6 |
|
Gimme a Drink!
Join Date: Dec 2002
Location: NYC
Posts: 694
|
Re: Pilot Bearing
its there for a reason, i would 100% use it
__________________
1990 GT,stock T-5,K&N w/o air silencer,March underdrives,FMS wires,timing@14*,PA Perf 130amp alt,Steeda Tri-Ax Shifter,Steeda adj quadrant/clutch cable/firewall adj,Centerforce II clutch,o/r x-pipe,Magnaflow SS catback,g-load brace, subframes,Bilstein struts/shocks,Autometer gauges, 136k and running strong! |
|
|
|
 |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Does the T-5 pilot bearing need to come out for an AOD to go in? | crazypete | Windsor Power | 14 | 11-06-2003 11:04 PM |
| Pilot Bearing | Cody2552 | Windsor Power | 2 | 04-09-2003 09:30 AM |
| Pilot Bearing | Falcons Talon | Windsor Power | 13 | 10-16-2002 06:44 PM |
| Pilot bearing replacement | Rebel79 | Windsor Power | 8 | 05-31-2002 02:12 PM |
| Need help getting pilot bearing out of crankshaft... | TROYXTROY | Windsor Power | 7 | 01-22-2001 04:25 PM |