Distributor alignment with Oil Pump Shaft

Dopie · 11-26-2001, 01:23 PM

Folks,
Every time I install the distributor in my 65 289, I have a devil of a time aligning the oil pump shaft. The shaft seems to lean over just enough to cause the shaft to not mate with the distributor. After I fool around with it for some time I can get the two to mate, but it seems that this shouldn't be this much hassel.

I have worked on several 289's in which everyone of them have this isssue. I ususally end up applying a heavy grease around the top of the shaft such that the grease won't allow the shaft to lean to the side.

I worked on one engine where the shaft retainer clip was not installed and the shaft fell into the oil pan.. NOT FUN.

Is there a trick or a tip ??

Dopie

Fostang · 11-26-2001, 06:14 PM

Might be time to replace either the shaft or the pump. It would be better that both were replaced. Could be the teeth have excessive wear on them therefore allowing the shaft to play. Not safe for your engine if this is the case. Or the same clip that fell off once may have move slightly down not holding the shaft in place. I'd look into that asap. Good luck.

shovelnose · 11-27-2001, 01:39 AM

I have had this problem too. I find the best way is to get the shaft in is to get the dist. lined up for timing then bump the motor over till the dist. drops down all the way. Helps if a friend wiggles the dist. I have never had the luxury of having the clip installed on the shaft.

Gearhead999 · 11-27-2001, 09:17 PM

Very common problem. Either bump it around till it lines up, as already stated, or put some wheel bearing grease on it to hold it away so the dist. will go in. Also, stated.

Clip never helped that much

mustangman65_79 · 12-03-2001, 06:59 AM

But alas, bumping the starter, I would not recomend. I now have a oil pump shaft in my oil pan because of this. Somehow it fell while the motor was being turned. I now just use wheel grease.

11-26-2001, 01:23 PM	#1
Dopie Registered Member Join Date: May 2001 Location: Cypress, Ca Posts: 8	Distributor alignment with Oil Pump Shaft Folks, Every time I install the distributor in my 65 289, I have a devil of a time aligning the oil pump shaft. The shaft seems to lean over just enough to cause the shaft to not mate with the distributor. After I fool around with it for some time I can get the two to mate, but it seems that this shouldn't be this much hassel. I have worked on several 289's in which everyone of them have this isssue. I ususally end up applying a heavy grease around the top of the shaft such that the grease won't allow the shaft to lean to the side. I worked on one engine where the shaft retainer clip was not installed and the shaft fell into the oil pan.. NOT FUN. Is there a trick or a tip ?? Dopie

11-26-2001, 06:14 PM	#2
Fostang Registered Member Join Date: Feb 2001 Location: Stockton, Ca Posts: 599	Might be time to replace either the shaft or the pump. It would be better that both were replaced. Could be the teeth have excessive wear on them therefore allowing the shaft to play. Not safe for your engine if this is the case. Or the same clip that fell off once may have move slightly down not holding the shaft in place. I'd look into that asap. Good luck. __________________ 67' Fastback-Supercharged 4.6 DOHC Cobra, T-56, 8.8 more to come. 67' Coupe-EFI, AOD, 8.8 90 Gt-Supercharged,MAF,TB,1.7's ripper, bassani x, 3.55's, 01' cobras, headers. 89'GT-Supercharged,Heads,Cam,Intake,TB,MAF,power pipe,headers,offroad exhaust,black bullits.

11-27-2001, 01:39 AM	#3
shovelnose Registered Member Join Date: Oct 2000 Location: Ontario, Canada Posts: 234	I have had this problem too. I find the best way is to get the shaft in is to get the dist. lined up for timing then bump the motor over till the dist. drops down all the way. Helps if a friend wiggles the dist. I have never had the luxury of having the clip installed on the shaft. __________________ 82 Mercury Capri 302, Comp. Cams, Tremec 3550, 3.73's, 12.8@106 N/A Kevin's Capri Kevin's Mustang

11-27-2001, 09:17 PM	#4
Gearhead999 Registered Member Join Date: Sep 1998 Location: Oviedo, FL Posts: 992	Very common problem. Either bump it around till it lines up, as already stated, or put some wheel bearing grease on it to hold it away so the dist. will go in. Also, stated. Clip never helped that much __________________ "Support our Troops" Dave 1968 Cougar 2004 Thunderbird 2007 F150 Harley-Davidson, SuperCrew 1986 LTD 1997 Ranger 1992 Honda Civic

12-03-2001, 06:59 AM	#5
mustangman65_79 My poor 79 RIP Join Date: Oct 2001 Location: Suisun City, Posts: 2,320	But alas, bumping the starter, I would not recomend. I now have a oil pump shaft in my oil pan because of this. Somehow it fell while the motor was being turned. I now just use wheel grease. __________________ '84 mustang GT turbo '85 LTD '89 Camaro Irocz z28 '94 Lightning '96 Trans am

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
damn it!! Broke the oil pump shaft.	Dark_5.0	Windsor Power	16	04-21-2004 10:32 PM
Should an 8 mustang dist. have a shorter oil pump shaft?	crazypete	Windsor Power	4	10-11-2002 08:48 PM
oil pump drive shaft	95mustang	Windsor Power	4	08-14-2002 09:35 AM
ARP oil pump drive shaft problems	yellowspeedster	Windsor Power	2	05-20-2002 05:18 PM
Tips on changing seized oil pump, shaft sheared	BowTie Eater 5 Liter	Windsor Power	0	02-13-2002 09:26 PM