MustangWorks.com - The Ford Mustang Power Source!

Go Back   MustangWorks.com : Ford Forums > Mustang & Ford Racing > Racer's Club House
Register FAQ Members List Calendar

Notices


Reply
 
Thread Tools Rate Thread Display Modes
Old 08-08-2001, 10:32 PM   #1
mattcstang
Registered Member
 
Join Date: Apr 2001
Location: St Louis MO
Posts: 9
Question Anyone running a C-4 tranny I need HELP!!!!!!!!

I was putting my tranny in tonight and had about 20min's in it got her in but ran into a little problem. The crossmember and tranny mount.What did you do with the crossmember and tranny mount? If I weld a 3x7in. plate to the top of the tranny mount, that bolts to the transmission, and drill new holes about 11/4in. forward I could bolt the tranny in. I'm thinking of doing this with 1/8in. steel? Has anyone else run into this problem? If you have what did you do? And will this pass with the tech man, or do you think this is a safe solution? Sorry it's so long trying to get to the track this weekend..

------------------
Matt Cruise
MUSTANG MUSCLE PERFORMANCE AND DYNO SERVICE
www.mustangmuscleonline.com
mattcstang is offline   Reply With Quote
Old 08-09-2001, 07:09 AM   #2
Jeff Chambers
Moderator
 
Jeff Chambers's Avatar
 
Join Date: Aug 2000
Location: Milan, OH
Posts: 2,699
Post

Jump over to the FFW site and ask the question in the Racer's Clubhouse. I'd think that some of the Renegade & Outlaw racers ought to be able to answer you question real quick.



------------------
Jeff Chambers
Trophy Stock #3
11.462 Seconds / 117.43 MPH
Chambers Racing Team
Jeff Chambers is offline   Reply With Quote
Old 08-09-2001, 11:26 AM   #3
mattcstang
Registered Member
 
Join Date: Apr 2001
Location: St Louis MO
Posts: 9
Post

Thanks Jeff already got it figured out.

------------------
Matt Cruise
MUSTANG MUSCLE PERFORMANCE AND DYNO SERVICE
www.mustangmuscleonline.com
mattcstang is offline   Reply With Quote
Old 08-10-2001, 06:47 AM   #4
Jeff Chambers
Moderator
 
Jeff Chambers's Avatar
 
Join Date: Aug 2000
Location: Milan, OH
Posts: 2,699
Post

What's the trick? I figured it'd be like the AOD, where you just grind the welds on the cross member and slide it back, then reweld it.

Inquiring minds want to know.


------------------
Jeff Chambers
Trophy Stock #3
11.462 Seconds / 117.43 MPH
Chambers Racing Team
Jeff Chambers is offline   Reply With Quote
Old 08-10-2001, 10:52 AM   #5
mattcstang
Registered Member
 
Join Date: Apr 2001
Location: St Louis MO
Posts: 9
Post

Thats it no trick just lost my mind.....to late and to hot out to think....

------------------
Matt Cruise
MUSTANG MUSCLE PERFORMANCE AND DYNO SERVICE
www.mustangmuscleonline.com
mattcstang is offline   Reply With Quote
Old 09-07-2006, 11:43 PM   #6
hemicross
show me my opponent
 
Join Date: Sep 2006
Location: El Paso Texas
Posts: 12
Cool Re: Anyone running a C-4 tranny I need HELP!!!!!!!!

hey I have a question since you seemed to have figured out your problem, were converting this 93 coupe 4 cyl to a 351w swap, I'm going to run a c-4 tranny and i have the true dual cross member so the bushing housings are not welded yet, from what I read I guess it will bolt up fine then I weld it, but beyond that, did your driveshaft fit right? and was the slip yoke the right splines?
hemicross is offline   Reply With Quote
Reply



Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
Yet another tranny fluid ?? Simi Stang Windsor Power 4 09-30-2003 12:44 PM
Tranny and rear end q Nixon1 Windsor Power 0 02-21-2003 02:06 PM
Tranny update...Lentech VB silver_pilate Blue Oval Lounge 10 05-02-2002 12:34 PM
The Motor Runnning and then...........Tranny Stang Runner Windsor Power 0 12-12-2001 01:48 PM
This is bad! Did my Uncle cause my Racing tranny to overheat?(It's a long 1... sorry) Stang_ROTY Windsor Power 1 08-30-2001 10:55 PM


All times are GMT -5. The time now is 12:27 AM.


SEARCH