© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
12-07-2002, 09:34 PM | #1 |
Registered Member
Join Date: May 2002
Location: South Carolina
Posts: 58
|
Help! - Pedistal Rocker Question
My pedistal roller rockers seemed to go on as stated in the intructions. I had about 1/2 to 3/4 of a turn after the pushrod made contact to bolt tightening.
When I did the final torque I noticed that the valves seemed to be opening slightly during that last 3/4 of a turn. Is this normal. Do they bleed back? Have I #$%^&@ up???? Help. Tell me all is fine. Please.
__________________
Bobasaurus 1987 LX 5.0 - Engine Rebuild now installed - 26290 Wonderful Miles so far Items now installed from the garage : GT-40p heads, Explorer Intake, FMS "P" headers, Crower 15511, SFI Balancer, 24#, SPEC Stage 1, T5z, 65MM TB, 77MM Pro-M, 255lph Pump |
12-07-2002, 10:58 PM | #2 |
Registered Member
Join Date: Aug 2002
Location: SanAntonio, Tx
Posts: 957
|
When i installed my 1.7's a little while back, i knew the instructions said 1 turn, but that was hard for me to determine, since my torque wrench would hit the hood before i could go 3/4 of a turn, i didnt use shims, but may have needed them, i guess it was'nt to far off since i felt, and saw a pretty good gain in performance, and e.t.s and mph, i didnt trap over 100mph until i insatlled my crane rr's, took me a couple hours, and im happy, almost in the 12's with stock heads cam and intake.
if you think it opend your valve then use shims, i doubt you need them unless you have had your heads milled, or machined at one time.
__________________
X-Texas highway patrol ssp 1990 coupe - exploder Gt-40 iron heads, Explorer intake, 19 lber's. E-cam. crane 1.7 rollers. 190fp. 75mm maf. 65mm tb, tubular subframe connectors, mac cai, Asp crank pulley, T-5, king cobra clutch, flowtech 1-5/8 unequals, mac X-pipe Frpp driveshaft, lakewood Lca's. race weight 3,160 12.69 @ 107.35, 1.71 60' 26x8.5 drag's 3.90 gear 13.20 @ 106.91 - 235/60/15 firestones 2.3 60' 3.27 gear |
12-08-2002, 12:05 AM | #3 |
Junior Member
Join Date: Mar 1999
Location: Ventura, California
Posts: 8,981
|
Apply compressed air to the spark plug hole at each cylinder when it's at TDC, and feel for air at the intake and exhaust ports. If none comes out, your more than likely fine.
Take care, ~Chris
__________________
Webmaster: Rice Haters Club Jim Porter Racing Peckerwoods Pit Stop Support Your Local
RED & WHITE! |
12-08-2002, 10:05 AM | #4 |
Registered Member
Join Date: Dec 2002
Location: Columbus, OH
Posts: 100
|
Chris is correct, just make sure the cylinder is on the compression stroke at TDC.
Sorry for the correction Chris, but that is often over looked Murdock |
12-08-2002, 10:50 AM | #5 |
Junior Member
Join Date: Mar 1999
Location: Ventura, California
Posts: 8,981
|
No apologies are necessary, that's a very good point!
Take care, ~Chris
__________________
Webmaster: Rice Haters Club Jim Porter Racing Peckerwoods Pit Stop Support Your Local
RED & WHITE! |
12-08-2002, 10:56 AM | #6 |
Registered Member
Join Date: May 2002
Location: South Carolina
Posts: 58
|
I feel better now
It passes the test. Whew!
Thanks guys.
__________________
Bobasaurus 1987 LX 5.0 - Engine Rebuild now installed - 26290 Wonderful Miles so far Items now installed from the garage : GT-40p heads, Explorer Intake, FMS "P" headers, Crower 15511, SFI Balancer, 24#, SPEC Stage 1, T5z, 65MM TB, 77MM Pro-M, 255lph Pump |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Roller rocker question? | HiFlow5 0 | Windsor Power | 1 | 05-18-2004 12:07 PM |
Rocker Question. | Mopar1 | Windsor Power | 1 | 09-20-2002 09:02 PM |
Rocker Arms Question | Falcons Talon | Windsor Power | 1 | 08-11-2002 11:27 PM |
Roller rocker question | DemonLp | Windsor Power | 1 | 03-22-2001 04:19 AM |
Rocker Panel Moldings Question | Matt683 | Classic Mustangs | 4 | 01-05-2001 02:46 PM |