![SEARCH](http://www.mustangworks.com/images/search.png)
![The Mustang Works](http://www.mustangworks.com/images/mw_footer_logo.gif)
© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
![]() |
#1 |
Registered Member
Join Date: Jan 2001
Location: compton, CA, USA
Posts: 63
|
![]() Anyone encounter a similar problem? Yesterday I check my passenger window motor because my window got stuck on the down position. When I removed the motor and press the up botton it worked. So when I put it back in the window went back up. Now it works perfect. But after that my power door locks wont lock. They will unlock when I press the button, but will not lock. I've check everything again, but can't find out whats wrong. Anyone have any suggestions?
|
![]() |
![]() |
![]() |
#2 |
Registered Member
Join Date: Jan 2001
Location: compton, CA, USA
Posts: 63
|
![]() added info:
90LX 5.0 |
![]() |
![]() |
![]() |
#3 |
Registered Member
Join Date: Jun 2001
Location: KC,Mo,US
Posts: 70
|
![]() I'm having the same problem with my car. I think it is the door lock acuaters going bad.
------------------ 95gt 80k, MSD 6AL, MSD coil, pulleys, fpr, cold air kit, off road h-pipe, flowmasters, 3.73, fluidampener, 9mm wires, mega bite jr lowers, kennybrown subframe connectors, edelbrock performer intake, 70mm TB, Aluminum Driveshaft, Tri-Ax shifter. |
![]() |
![]() |
![]() |
#4 |
Registered Member
Join Date: Jan 2001
Location: compton, CA, USA
Posts: 63
|
![]() I was thinking the same thing, but I't happens on both doors, they will unlock but not lock. Also one on the acuators is new.
|
![]() |
![]() |
![]() |
#5 |
Registered Member
Join Date: Jul 2000
Location: Lawrence, KS, USA
Posts: 169
|
![]() check your switches on the doors arm rests
try pulling one and putting in one from the window rollup/down. all the switches are the same, so they should be interchangeable that will rule out bad switches, after that test the wiring w/ a voltmeter at the motor, after that, replace the motor i already replaced one of mine and getting ready to do the next once it fails... ------------------ SHaFTed 91GT, 2 chamber flows, dumps, 70MM BBK TB, K&N conical, Robert Shaw tstat, Hurst short throw, T5, 17" Lexani Roma wheels, 235/40/R17 on front, 255/45/R17 on back, mach1 hood, LX tail lights, bright red! |
![]() |
![]() |
![]() |
#6 |
Registered Member
Join Date: Nov 2000
Location: Kailua, HI, USA
Posts: 21
|
![]() Hey there Evil I agree with checking the switches. Mine did the exact same thing and that is what it ended up being. It is a simple 5 min. job.
Good Luck! |
![]() |
![]() |
![]() |
#7 |
Registered Member
Join Date: Jan 2001
Location: compton, CA, USA
Posts: 63
|
![]() I'll check the switches today.
Thanks guys for the info. |
![]() |
![]() |
![]() |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
loss of power suddenly | jimdrechsler | Windsor Power | 17 | 09-30-2004 08:49 PM |
power for 500 hp daily | Torinalth | Power Adders | 22 | 09-25-2003 11:54 PM |
Power for the Power Amp | traderguy | Audio, Security, & Electronics | 2 | 07-13-2003 08:07 PM |
power shift? | JamGtStang | Windsor Power | 6 | 03-01-2001 02:11 PM |
Electrical power, where to splice? | Chris_H | Windsor Power | 3 | 02-11-2001 08:29 PM |