What Can I Expect From This

burn rubber · 10-04-2002, 01:59 AM

Hi, i was wondering what i could expect from my combo here and if you could tell me if it will all work together good

every part is brand new except for the block.

Its a 302 bored .040 over, I have edelbrock performer rpm heads with 2.02 intake valves, edelbrock performer rpm airgap polished intake, holley 750 dp 4 barrel, msd pro billit distributer, msd ignition box 6al, blaster 2 coil, comp cam (magnum #280h I .512 E .512 280 280) comp timing set, comp pushrods, comp full roller rockers. mac shortie headers ceramic coated.

Will this set up work together? Any info will be very helpful. This is my first time building a semi-race motor.

burn rubber · 10-05-2002, 02:45 AM

anyone?

HotRoddin · 10-05-2002, 03:22 AM

I'd say it sounds like a good combination ... good power output and still streetable ... you could probably get buy with a 650 on the carb but this leaves you room to grow.

what kind of compression ratio with that combo give you ?

burn rubber · 10-05-2002, 04:48 AM

9.5 : 1

WADS56 · 10-05-2002, 09:44 AM

I think it looks good. The carb is a litle big a 650 would be better but you have it so use it.

burn rubber · 10-06-2002, 05:06 AM

any guesstiments on hp?

burn rubber · 10-20-2002, 02:02 AM

Havent fired it up yet. I just bought the edelbrock nitrous kit for it too. pn#70001. It is the 50 75 100 shot kit. If I run the 100 shot, do you think it will put me in the 12's? Can't wait to turn the key.....another week.look at the pics below.

10-04-2002, 01:59 AM	#1
burn rubber Registered Member Join Date: Sep 2002 Location: maryland Posts: 22	What Can I Expect From This Hi, i was wondering what i could expect from my combo here and if you could tell me if it will all work together good every part is brand new except for the block. Its a 302 bored .040 over, I have edelbrock performer rpm heads with 2.02 intake valves, edelbrock performer rpm airgap polished intake, holley 750 dp 4 barrel, msd pro billit distributer, msd ignition box 6al, blaster 2 coil, comp cam (magnum #280h I .512 E .512 280 280) comp timing set, comp pushrods, comp full roller rockers. mac shortie headers ceramic coated. Will this set up work together? Any info will be very helpful. This is my first time building a semi-race motor. __________________ 01 GT 12.3 @ 112mph Steeda timing adjuster,Steeda underdrive pullies, ,steeda tri-ax 3650 shifter,24#fms injecters,bbk 70mm throttlebody,80mm maf,bassanni x pipe, Borla Side Exit exhaust, fms 4.10's, moser 31 spline axles, custom diablo chip.Steeda caster camber plates,g-trac bar,cobra r ground effects and hood,cobra r springs,ported upper intake.Comp cams #102600,fms jet hot coated shorty headers,mod max cam gears. msd 7020 Stacker 8

10-05-2002, 04:48 AM	#4
burn rubber Registered Member Join Date: Sep 2002 Location: maryland Posts: 22	9.5 : 1 __________________ 01 GT 12.3 @ 112mph Steeda timing adjuster,Steeda underdrive pullies, ,steeda tri-ax 3650 shifter,24#fms injecters,bbk 70mm throttlebody,80mm maf,bassanni x pipe, Borla Side Exit exhaust, fms 4.10's, moser 31 spline axles, custom diablo chip.Steeda caster camber plates,g-trac bar,cobra r ground effects and hood,cobra r springs,ported upper intake.Comp cams #102600,fms jet hot coated shorty headers,mod max cam gears. msd 7020 Stacker 8

10-05-2002, 09:44 AM	#5
WADS56 gear banger Join Date: Aug 2000 Location: CHICAGO Posts: 1,144	I think it looks good. The carb is a litle big a 650 would be better but you have it so use it. __________________ 79 Hatch: NA 347, Stage 2 Canfield Heads, Victor JR. Intake, Blueprinted Holley 750 HP, Solid Roller Cam, Shooting for 10's on motor 93 LX: Tremec, dual friction clutch, fms flywheel, Hedman shorties, O/R H-pipe Ricer hater's club member #49

10-06-2002, 05:06 AM	#6
burn rubber Registered Member Join Date: Sep 2002 Location: maryland Posts: 22	any guesstiments on hp? __________________ 01 GT 12.3 @ 112mph Steeda timing adjuster,Steeda underdrive pullies, ,steeda tri-ax 3650 shifter,24#fms injecters,bbk 70mm throttlebody,80mm maf,bassanni x pipe, Borla Side Exit exhaust, fms 4.10's, moser 31 spline axles, custom diablo chip.Steeda caster camber plates,g-trac bar,cobra r ground effects and hood,cobra r springs,ported upper intake.Comp cams #102600,fms jet hot coated shorty headers,mod max cam gears. msd 7020 Stacker 8

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
how much Power would u guys expect from this combo?	fiveOguy20	Windsor Power	6	09-20-2002 02:42 PM
What to expect?	66 Racer	Stang Stories	9	10-14-2001 05:17 PM
What to expect?	66 Racer	Classic Mustangs	1	10-11-2001 08:51 PM
What Should I Expect To Gain With BBK 1-5/8 Equal Shortys & Off Road H-Pipe???	BowTie Eater 5 Liter	Windsor Power	1	10-08-2001 12:24 PM
What to expect from ported stock lower?	jeb	Windsor Power	1	03-19-2001 09:38 PM

10-05-2002, 02:45 AM	#2
burn rubber Registered Member Join Date: Sep 2002 Location: maryland Posts: 22	anyone? __________________ 01 GT 12.3 @ 112mph Steeda timing adjuster,Steeda underdrive pullies, ,steeda tri-ax 3650 shifter,24#fms injecters,bbk 70mm throttlebody,80mm maf,bassanni x pipe, Borla Side Exit exhaust, fms 4.10's, moser 31 spline axles, custom diablo chip.Steeda caster camber plates,g-trac bar,cobra r ground effects and hood,cobra r springs,ported upper intake.Comp cams #102600,fms jet hot coated shorty headers,mod max cam gears. msd 7020 Stacker 8

10-05-2002, 03:22 AM	#3
HotRoddin cranky old man Join Date: Sep 2001 Location: Longview Texas Posts: 683	I'd say it sounds like a good combination ... good power output and still streetable ... you could probably get buy with a 650 on the carb but this leaves you room to grow. what kind of compression ratio with that combo give you ?