![SEARCH](http://www.mustangworks.com/images/search.png)
![The Mustang Works](http://www.mustangworks.com/images/mw_footer_logo.gif)
© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
![]() |
#1 |
Registered Member
Join Date: May 2001
Location: Maryland
Posts: 138
|
![]() What is the correct way to do a compression test. Also what numbers should I be looking for on my car. It has 60,000 miles on it.
__________________
Motorsports springs, Lakewood drag struts, Southside rear lower arms. Motorsports upper arms. Lakewood Drag shocks. Southside rear drag springs, sub frames, 3.55 Gears, Cobra intake, 70mm TB, GT40 heads, X Cam, 1.6 Crane RR's, 110lph fuel pump, AFPR, offroad h pipe, Flowmaster catback, 1 5/8" Motorsport headers, under drive pulleys, cold air induction, Black Magic Fan, Pro 5.0, Weld Draglites. |
![]() |
![]() |
![]() |
#2 |
347ci of HORSE POWER!!!
Join Date: Jul 2001
Location: Houston, TX
Posts: 1,416
|
![]() Well, there is a compression test kit you can buy. You'll have to have access to a compressor inorder to do this. I ran one on mine as well as a leak down test. I pulled 100psi on all 8. That's real good for a stock long block with 100+ miles on it. My friends drag car with 11:1 compression pulled a 130psi.
|
![]() |
![]() |
![]() |
#3 |
Junior Member
Join Date: Mar 1999
Location: Ventura, California
Posts: 8,981
|
![]() There are two compression tests that you should perform; Wet and dry. Do the dry test first.
For accuracy, you MUST perform the compression tests with the engine as close to operating temp as possible, and have the throttle blocked open. You should also do both tests at the same time, dry first. You do not need an air compressor to do this. In short: 1) Warm up the engine 2) Disconnect the coil 3) Block the throttle so that it is wide open 4) Remove all 8 spark plugs 5) Install the tester and crank the engine through 5 revolutions 6) Read and write down the results 7) Repeat steps 5 & 6 for the remaining cylinders 8) Add 3 squirts of engine oil into the spark plug hole of the first cylinder you tested, and test it again 9) Read and write down the results 10) Repeat step 8 & 9 for each of the remaining cylinders, but do not add the oil until you are about to test that specific cylinder. Adding oil to all of the cylinders at the same time won't work correctly. Your numbers will be higher after the wet test. The numbers themselves aren't as important as the difference between them. Post your results. Take care, -Chris
__________________
Webmaster: Rice Haters Club Jim Porter Racing Peckerwoods Pit Stop Support Your Local
RED & WHITE! |
![]() |
![]() |
![]() |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
Attn: PKRWUD: Compression Test Results | 95mustanggt | Windsor Power | 13 | 06-22-2004 07:34 AM |
Looking to buy and I need Advice...Fuel Pressure Test Gage and Compression Test Gage | MTU 50 | Windsor Power | 3 | 10-18-2002 05:34 PM |
Cold compression test? | 92Rustang | Windsor Power | 3 | 12-17-2001 09:47 PM |
gonna do a compression test! | Cannon | Windsor Power | 1 | 03-22-2001 09:14 PM |
Compression test... | Red96GT | Modular Madness | 1 | 12-03-1999 01:49 PM |