![SEARCH](http://www.mustangworks.com/images/search.png)
![The Mustang Works](http://www.mustangworks.com/images/mw_footer_logo.gif)
© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
|
![]() |
#1 |
Registered Member
Join Date: Jan 2001
Location: Kintnersville, PA USA
Posts: 38
|
![]() I was wondering if anyone has done a trickflow street intake install. I am about to do mine but te directions are vague about all vaccuum hookups. Are you supposed to connect them or use the caps they provide to cover them up? Thanks for the help in advance!
__________________
91 LX: Green/white stripes, TFS heads, intake, cam, and 1.7 rockers. BBK longtubes, off-road h-pipe w/ flowmasters. |
![]() |
![]() |
![]() |
#2 |
Registered Member
Join Date: Jan 2001
Location: Salt Lake City
Posts: 117
|
![]() Just got done with mine.
The Trick Flow instructions are good for some things but are way lacking in some steps. The best thing I did was buy a few lengths of different size vacuum hoses. I used almost 3 feet of 3/8 ID. I just turned both my stock and the TFS intake upside down and transfered all the removable fittings and hoses to the new one. The side port is different, so you can see that you have to use a new section of hose. Just make sure that you basically have the same lines and hoses as your stock setup. Leave extra length if in doubt because you will not want to pull the intake back off if you find you need a longer hose. I had to put in a longer hose to reach my PCV and also for the hose going into the vacuum tree on the firewall. I didn't have to use all the fittings that were in the kit. Wait till you get to fight with those stupid 12 point nuts. I think the TFS guys were on drugs when they decided how much clearance to allow for the nuts. It's a joke that they give torque values because I couldn't possibly get a socket on two of them, even with a swivel. BTW you need a 3/8 12-point box end wrench for them. 5/16 & 3/8 12-point sockets for the others. Don't thread the studs too far into the lower intake, or you will not get full threads on the nuts. I was well versed in swear words by the time I was done. I just hated having to take it on and off so many times. Especially since I had to thread it through my strut tower brace that I was too lazy to remove. Also, cut 4 long bolts to make guide pins to align the lower as you set it down. Let me know if you have other questions, Dan
__________________
Spec Service (UHP), BFG G-Force KDW's, Turbo Coupe 3.55 rear w/disks, 73mm calipers, Stg 1 Twisted Wedges, TFS Street Intake, 70mm TB, E cam, Crane 1.7's, Aeromotive FPR, BBK 1 5/8 shorties, elec fan, FMS Al Radiator, Moroso Wires, Kenne Bell Ramair, March pulleys, Race Magnums, 190 lph Walbro, FMS Al Dshaft, D/S loop, MM 4point rollbar, FMS C spngs, strut tower brace, Tokico Illuminas, Prothane bushings, MM Lwr Conrol Arms, KB welded subs, Cervini Mach 1 hood/valence/side skirts/wing/airdam. |
![]() |
![]() |
![]() |
#3 |
Mustangs
Join Date: Jul 2000
Posts: 1,938
|
![]() Wow....just in time, probably in the next couple of days my TFS street intake is going on as well.
DZEE'S LX - Did you notice any difference in power after installing the intake manifold?
__________________
2005 Suzuki Hayabusa GSX1300-R 1980 Ford Thunderbird - 255 V8 ported heads, 5.0L ported stock headers, O.R. H-pipe and Flowmaster 2-chambers, dual roller timing chain hi-po Mack Truck hood emblem ![]() 1985 Mustang GT 5.0L T5, F-303, GT40p, headers, off-road h, flowmasters, MSD stuff, etc. Sold 02/06/04 ![]() 1989 Mustang GT ET: 13.304@102.29 mph (5-24-03) Sold - 1998 Mustang Cobra coupe, 1/4 mile - street tires: 13.843@103.41 (bone stock) |
![]() |
![]() |
![]() |
#4 |
Registered Member
Join Date: Jan 2001
Location: Salt Lake City
Posts: 117
|
![]() Haven't driven it yet.
See my post on my noise..... Am cleaning up the mess in my garage as I wait to see if anyone has any ideas. A little leary about driving it before I know if it could be a major problem. Dan |
![]() |
![]() |
![]() |
#5 |
Moderator
Join Date: Dec 1999
Location: Livonia, MI, USA
Posts: 1,194
|
![]() Talk about timing...
Dude, you gotta get all of us to finish while YOU be the Guinea pig ![]() ![]() Getting there..... ![]()
__________________
Darius Rudis, Moderator Corner Carvers Delight 1989 Mustang LX - Open Track Car http://www.dariusrudis.com |
![]() |
![]() |
![]() |
#6 |
Registered Member
Join Date: Aug 2000
Location: Wisconsin
Posts: 879
|
![]() me and my buddy did mine..i remember having to get a longer tube for the PCV but dont remember the rest...and if you still have that stock rubber cover that goes over your distributer...mine didnt fit after words...intakes to big
![]()
__________________
'91 GT,410W,10.5 to 1 comp,Victor Jr. heads,Victor 5.8 intake,FTI cam,Crane retro fit lifters,Scorpian 1.6 RR's,Melling HV oil pump,MSD distro.,Canton oil pan,FMS flywheel,Romac balancer,FMS timing chain,Accufab 90mm TB,C&L 76mm maf, 42lbers,HD clutch,K&N air filter,Mac long tubes,Pro dumps,powerchamber,FMS 9mm wires,180 thermostat,Ford Racing gauges,5inch Tach,centerline convo pro's,nitto DR's,Pro3i lower control arms,50/50 shocks,3.55 gears,TFS HD diff. cover Next year: Tremec TKO,Spec stage 3 clutch,alum driveshaft,complete fuel system www.angelfire.com/linux/demondan |
![]() |
![]() |
![]() |
#7 |
Registered Member
Join Date: Mar 2000
Location: Springfield, Ma, usa
Posts: 706
|
![]() Do exactly what DZEE'S LX said and you'll be set! I had the same problems and did the same thing he did. I too believe the designers of that intake were on crack when they made it. I did notice more power after 4 grand, felt stronger, and in higher rpms the engine seemed to growl more
![]()
__________________
NewEngland Auto www.baystategearheads.com -91 Mustang Coupe, ex 4cyl (sold) -99 F150, 3" lift, 35" Procomps, Magnaflow exhaust Last edited by HiFlow5 0; 03-12-2002 at 08:43 AM.. |
![]() |
![]() |
![]() |
#8 |
Registered Member
Join Date: Aug 2000
Location: Wisconsin
Posts: 879
|
![]() YES! definitly use guide pins...i didnt and the passanger side gasket slide..leting antifreeze into the cylinder....got about half a block and it water locked....trust me..it sucks really bad...to have antifreeze pouring out your exhaust.....nope nope..you definitly dont want a V8 water pump
__________________
'91 GT,410W,10.5 to 1 comp,Victor Jr. heads,Victor 5.8 intake,FTI cam,Crane retro fit lifters,Scorpian 1.6 RR's,Melling HV oil pump,MSD distro.,Canton oil pan,FMS flywheel,Romac balancer,FMS timing chain,Accufab 90mm TB,C&L 76mm maf, 42lbers,HD clutch,K&N air filter,Mac long tubes,Pro dumps,powerchamber,FMS 9mm wires,180 thermostat,Ford Racing gauges,5inch Tach,centerline convo pro's,nitto DR's,Pro3i lower control arms,50/50 shocks,3.55 gears,TFS HD diff. cover Next year: Tremec TKO,Spec stage 3 clutch,alum driveshaft,complete fuel system www.angelfire.com/linux/demondan |
![]() |
![]() |
![]() |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
Edelbrock RPM intake install problems | jruppert | Windsor Power | 4 | 03-04-2004 05:05 PM |
Trick Flow intake problems | shacar87 | Windsor Power | 9 | 11-14-2003 05:53 PM |
Cobra Intake? | 95mustanggt | Windsor Power | 5 | 10-01-2002 09:55 AM |
upper intake and egr spacer install..... | scale | Windsor Power | 3 | 08-18-2002 11:37 PM |
new coolant leak after intake install | fiveohpatrol | Windsor Power | 15 | 03-04-2001 09:15 PM |