Hybrid Mode
© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
|
|
01-29-2007, 10:29 PM
|
#1 |
|
Registered Member
Join Date: Jan 2007
Posts: 12
|
Re: Valves
thats cool but what size roller rockers did u have USMC302 i have 1.7 roller rockers
__________________
hrdroc-.600 lift springs GT40P heads ported all the way out,1.6 ratio roller rockers,24lb injectors,70mm throttle body,under pulley's,cobra intake port match to the head,trick flow stage 1 cam .499/.510 lift,cold air intake,73mm mass air meter,adj fuel pressure regulator. stock bottom end et street slicks- 13.50@104.99 best 60ft. 1.720 3.73 gears reg street tires- 14.89@101.25 best 60ft. 2.090 3.08 gears |
|
|
|
01-30-2007, 12:07 AM
|
#2 |
|
Registered Member
Join Date: Sep 2000
Location: rock hill,S.C. 29730
Posts: 420
|
Re: Valves
We used axle grease to check my P to V clearance on my motor with 58cc heads TFS #1 cam and 1.6 rockers, spun it over, pulled the head off and the valves didn't even have any grease on them!!
And we had it smeared on the piston pretty thick, so I think your OK too.
__________________
88 GT: subs,pullies, 1 3/4 longtubes, flowmasters, AFR 165's,T,F #1 cam,Thyphoon intake, 24# inj., 73mm C&L,65mmT.B., 190LPH pump, Eagle sir rods, forged pistons in a newly rebuilt 306. DYNO TUNED TO 300.97 RWHP 337RWTQ |
|
|
|
|
01-30-2007, 04:34 AM
|
#3 |
|
Registered Member
Join Date: Jan 2007
Posts: 12
|
Re: Valves
all right that sounds like a good thing to do...that is one way of checking it cool thanks man...my total lift with 1.7 roller rocker is .531/.542
__________________
hrdroc-.600 lift springs GT40P heads ported all the way out,1.6 ratio roller rockers,24lb injectors,70mm throttle body,under pulley's,cobra intake port match to the head,trick flow stage 1 cam .499/.510 lift,cold air intake,73mm mass air meter,adj fuel pressure regulator. stock bottom end et street slicks- 13.50@104.99 best 60ft. 1.720 3.73 gears reg street tires- 14.89@101.25 best 60ft. 2.090 3.08 gears |
|
|
|
|
01-30-2007, 10:10 AM
|
#4 | |
|
Registered Member
Join Date: Apr 2001
Location: Gallatin, Tn
Posts: 1,326
|
Re: Valves
Quote:
__________________
|
|
|
|
|
|
01-30-2007, 10:31 PM
|
#5 |
|
Ride Hard
Join Date: Oct 2000
Location: Wyoming IL
Posts: 1,094
|
Re: Valves
I have e7's with 1.7 rockers and the stage 1, all on a stock bottom end. I think you will be fine.
__________________
65 Fastback 91 roller 306, H/C/I AOD-Bauman, PI Stallion, 4.10's and traction loc 04 Grand Cherokee Freedom Edition 79 Ford F-250 4x4 - Restored |
|
|
|
|
02-02-2007, 04:30 AM
|
#6 |
|
Registered Member
Join Date: Jan 2007
Posts: 12
|
Re: Valves
the only thing that i need to fine out now is the gt40p heads that i have i dont know the cc's on the heads the heads were on the car when i both it and i dont know if its 64cc 60cc 58ccc or what so thats what i need to fione out now
__________________
hrdroc-.600 lift springs GT40P heads ported all the way out,1.6 ratio roller rockers,24lb injectors,70mm throttle body,under pulley's,cobra intake port match to the head,trick flow stage 1 cam .499/.510 lift,cold air intake,73mm mass air meter,adj fuel pressure regulator. stock bottom end et street slicks- 13.50@104.99 best 60ft. 1.720 3.73 gears reg street tires- 14.89@101.25 best 60ft. 2.090 3.08 gears |
|
|
|
 |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| valves | jhun66stang | Classic Mustangs | 17 | 11-12-2006 06:21 PM |
| New Valves | Florida Stang | Windsor Power | 2 | 03-13-2002 08:22 AM |
| Help with valves!!!!!!! | Stang Runner | Windsor Power | 3 | 09-16-2001 12:33 PM |
| Help with valves!!!!!!! | Stang Runner | Windsor Power | 0 | 09-15-2001 04:11 PM |
| Valves | Patrick Boetticher | Windsor Power | 0 | 03-05-2001 10:31 PM |