© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
|
|
Thread Tools | Rate Thread | Display Modes |
11-25-2001, 04:29 PM | #1 |
It's a lot like a race car
Join Date: Aug 2000
Location: Meridian, MS
Posts: 4,130
|
Will a Edelbrock Performer RPM and a Holley fit under the stock hood
Will a Elelbrock performer RPM intake and a Holley four-barrel fit under my stock hood if I use a drop base air cleaner?
__________________
1987 Buick T-type 1998 HD Electra Elide |
11-25-2001, 11:17 PM | #2 |
Registered Member
Join Date: Oct 2001
Location: Florida Keys
Posts: 593
|
Hey man I
__________________
89 notch-finally not stock!! ported gt40's, ported cobra intake, 65mm tb, 75mm maf, mac cai, lt's,prochamber, fms 1.6 rr, 125 shot. |
11-25-2001, 11:19 PM | #3 |
Registered Member
Join Date: Oct 2001
Location: Florida Keys
Posts: 593
|
Hey man Im pretty sure it will fit, my buddy down here had either the performer or the performer rpm on his car with a 650 holley and it fit fine, you might want to get the covertible motor mounts, they drop the motor down a little lower that stock, so you can run a regular air cleaner. Good Luck, John
__________________
89 notch-finally not stock!! ported gt40's, ported cobra intake, 65mm tb, 75mm maf, mac cai, lt's,prochamber, fms 1.6 rr, 125 shot. |
11-25-2001, 11:33 PM | #4 |
Registered Member
Join Date: Nov 2001
Location: austin TX
Posts: 115
|
i know its not exactly the set up you have but i have a wiend intake, holly carb and a 1 inch spacer inbetween, 2 inch high ford motorsport air filter,with the stock hood, and im pretty sure stock motor mounts. i dont know if that helps any
__________________
'87 coupe, 308, world product windsor jr. heads, comp cams 220@.050/.512 @110 deg., roller cam,crane full roller rockers, 4bbl 600cfm holly carb,1 inch spacer, wiend aluminum intake, pullies, msd distributer/ignition, 1 5/8 bbk shorties, off road h-pipe 2 chamber flows, 3.73 posi rear end, P.S.T control arms, steeda tri-ax shifter, t-5, auto meter guages, and more to come (hopefully ) |
11-25-2001, 11:45 PM | #5 |
Registered Member
Join Date: Apr 2000
Location: middleburg, fl, usa
Posts: 1,134
|
Yes it will fit, I ran that same thing under the stock hood for a while and had plenty of hood clearance.
__________________
James Cox RHC Member #44 nochevy@hotmail.com 1991 Mustang LX Dart iron eagle block, 4340 28oz 347 crank, 4340 h-beam rods, probe ultra light pistons canfield heads “race ported by Brent Frazier”, solid roller cam and lifters “custom grind”, kooks 1 7/8" race headers, and much more. Engine built by Brent Frazier. |
11-26-2001, 01:14 AM | #6 |
All about the Windsor.
Join Date: Feb 2000
Posts: 2,052
|
if it doesn't fit cut a big hole around the carb and get one of those scoops out of Summit that have the 3 red butterfly flaps that hook up to your throttle. But keep it out of the rain...
|
11-27-2001, 01:57 AM | #7 |
Registered Member
Join Date: Oct 2000
Location: Ontario, Canada
Posts: 234
|
Edlebrock RPM, holley 600 cfm, 3X14" K/N, stock mounts. No problems here.
Could mabey get away with 1" spacer(Maybe not).
__________________
82 Mercury Capri 302, Comp. Cams, Tremec 3550, 3.73's, 12.8@106 N/A Kevin's Capri Kevin's Mustang |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Typhoon Intake vs Edelbrock Performer RPM | lucheski | Windsor Power | 1 | 07-13-2004 12:54 PM |
GM Engines | BLOCKER | Blue Oval Lounge | 2 | 04-13-2004 12:35 AM |
Edelbrock Performer RPM heads...... | topless5.0 | Windsor Power | 1 | 08-12-2002 10:20 PM |
edelbrock performer rpm heads | hippi97 | Windsor Power | 2 | 04-01-2001 08:40 PM |
Performer VS. Performer RPM | IMPULSERACING | Windsor Power | 8 | 02-09-2001 12:45 PM |