GTech vs Track?????

Stang Runner · 06-19-2001, 08:41 PM

I know going to the track is better but how good is the Gtech at the 1/4 How close is the Time@MPH to the track? any one used the Gtech at the Track? I just ran a
0-60MPH 6.29
1/4 14.90@100.2MPH
The very Bad time is my gears and my Trans and the New Stock Cluch That slips bad got a bit of spin in 1st and more in 2nd I finished in 3 at about 5000rpms

------------------
1988 LX 5.0 3060lbs (full Tank)
Drivetrain: 2.73 Stock Gears, World Class T-5, Lakewood Bellhousing, Summit Adjustable Cluch Quadrant & Cable, Alumminum Driveshaft, Flaming River Manual Steering Rack
Suspension: MAC Control Arms,Maximum Motorsports Front Grip Package, H&R Sport Spings, Bilstein Shocks
Engine: Steal Mounts, Ram air, K&N, Under Drive Pulles
Exhaust: 1 5/8 Un-Equal Length Mac Headers, X-pipe W\cats, Edelbrock cat\back

fiveohpatrol · 06-19-2001, 10:55 PM

i've tested it and its about .01-.015 seconds and 4-5 mph faster than the actual track numbers,so you will probably actually run a 15.0 @95mph or so, this is very typical of any stock geared 5.0, you need gears BADLY, with your mods, a set of 3.73s should cut atleast a half second off your times

------------------
88 Notch, 3.73's, Ported E7's, Explorer int. w/ ported lower, pulleys, 1.7RR's, BBK headers, off-road H-pipe, flowmasters, subframe connectors, 65mm TB, shift kit, March ram air ,MSD coil, U/L control arms, 155lph fuel pump, cheap 2800 stall, Crane Adj.FPR, best 1/4--> 13.77@101.35

Stang Runner · 06-20-2001, 05:37 PM

I realy need gears I CANT even SPIN them in 1st

By the end of next month I will get some 3.73 I had a LOT more power when I had the stock T-5 I had a best of 13.8@106 with the tires spiing all though 1&2 to about 55MPH NOw all I can get is a 2IN Brunout. I hope I can take 1sec. off and add about 5MPH I think I will need to get a cluch to do that It may be optimistic But I can Hope

06-19-2001, 08:41 PM	#1
Stang Runner Registered Member Join Date: Jun 1999 Location: Walker, MI, USA Posts: 1,202	GTech vs Track????? I know going to the track is better but how good is the Gtech at the 1/4 How close is the Time@MPH to the track? any one used the Gtech at the Track? I just ran a 0-60MPH 6.29 1/4 14.90@100.2MPH The very Bad time is my gears and my Trans and the New Stock Cluch That slips bad got a bit of spin in 1st and more in 2nd I finished in 3 at about 5000rpms ------------------ 1988 LX 5.0 3060lbs (full Tank) Drivetrain: 2.73 Stock Gears, World Class T-5, Lakewood Bellhousing, Summit Adjustable Cluch Quadrant & Cable, Alumminum Driveshaft, Flaming River Manual Steering Rack Suspension: MAC Control Arms,Maximum Motorsports Front Grip Package, H&R Sport Spings, Bilstein Shocks Engine: Steal Mounts, Ram air, K&N, Under Drive Pulles Exhaust: 1 5/8 Un-Equal Length Mac Headers, X-pipe W\cats, Edelbrock cat\back

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Track conditions	Eric4Nitrous	Windsor Power	12	11-22-2002 10:59 PM
Tell me what you think...track numbers	silver_pilate	Blue Oval Lounge	5	10-30-2001 03:44 PM
Annoying things at the track...Top five list	Dark_5.0	Blue Oval Lounge	10	10-11-2001 07:33 AM
Mustang Club of Central Iowa Autocross - May 6 - Marshalltown Go-Kart Track	KB1991	Ford Show & Go	0	05-03-2001 12:33 PM
Mustang Club of Central Iowa Autocross - May 6 - Marshalltown Go-Kart Track	KB1991	Corner Carvers Delight	0	05-03-2001 12:32 PM

06-19-2001, 10:55 PM	#2
fiveohpatrol I'd rather be basketweaving Join Date: Feb 2000 Location: Indianapolis Posts: 2,551	i've tested it and its about .01-.015 seconds and 4-5 mph faster than the actual track numbers,so you will probably actually run a 15.0 @95mph or so, this is very typical of any stock geared 5.0, you need gears BADLY, with your mods, a set of 3.73s should cut atleast a half second off your times ------------------ 88 Notch, 3.73's, Ported E7's, Explorer int. w/ ported lower, pulleys, 1.7RR's, BBK headers, off-road H-pipe, flowmasters, subframe connectors, 65mm TB, shift kit, March ram air ,MSD coil, U/L control arms, 155lph fuel pump, cheap 2800 stall, Crane Adj.FPR, best 1/4--> 13.77@101.35

06-20-2001, 05:37 PM	#3
Stang Runner Registered Member Join Date: Jun 1999 Location: Walker, MI, USA Posts: 1,202	I realy need gears I CANT even SPIN them in 1st By the end of next month I will get some 3.73 I had a LOT more power when I had the stock T-5 I had a best of 13.8@106 with the tires spiing all though 1&2 to about 55MPH NOw all I can get is a 2IN Brunout. I hope I can take 1sec. off and add about 5MPH I think I will need to get a cluch to do that It may be optimistic But I can Hope