Hybrid Mode
© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
|
|
08-08-2001, 10:32 PM
|
#1 |
|
Registered Member
Join Date: Apr 2001
Location: St Louis MO
Posts: 9
|
Anyone running a C-4 tranny I need HELP!!!!!!!!
I was putting my tranny in tonight and had about 20min's in it got her in but ran into a little problem. The crossmember and tranny mount.What did you do with the crossmember and tranny mount? If I weld a 3x7in. plate to the top of the tranny mount, that bolts to the transmission, and drill new holes about 11/4in. forward I could bolt the tranny in. I'm thinking of doing this with 1/8in. steel? Has anyone else run into this problem? If you have what did you do? And will this pass with the tech man, or do you think this is a safe solution? Sorry it's so long trying to get to the track this weekend..
------------------ Matt Cruise MUSTANG MUSCLE PERFORMANCE AND DYNO SERVICE www.mustangmuscleonline.com |
|
|
|
08-09-2001, 07:09 AM
|
#2 |
|
Moderator
Join Date: Aug 2000
Location: Milan, OH
Posts: 2,699
|
Jump over to the FFW site and ask the question in the Racer's Clubhouse. I'd think that some of the Renegade & Outlaw racers ought to be able to answer you question real quick.
------------------ Jeff Chambers Trophy Stock #3 11.462 Seconds / 117.43 MPH Chambers Racing Team |
|
|
|
|
08-09-2001, 11:26 AM
|
#3 |
|
Registered Member
Join Date: Apr 2001
Location: St Louis MO
Posts: 9
|
Thanks Jeff already got it figured out.
------------------ Matt Cruise MUSTANG MUSCLE PERFORMANCE AND DYNO SERVICE www.mustangmuscleonline.com |
|
|
|
|
08-10-2001, 06:47 AM
|
#4 |
|
Moderator
Join Date: Aug 2000
Location: Milan, OH
Posts: 2,699
|
What's the trick? I figured it'd be like the AOD, where you just grind the welds on the cross member and slide it back, then reweld it.
Inquiring minds want to know. ------------------ Jeff Chambers Trophy Stock #3 11.462 Seconds / 117.43 MPH Chambers Racing Team |
|
|
|
|
08-10-2001, 10:52 AM
|
#5 |
|
Registered Member
Join Date: Apr 2001
Location: St Louis MO
Posts: 9
|
Thats it no trick just lost my mind.....to late and to hot out to think....
------------------ Matt Cruise MUSTANG MUSCLE PERFORMANCE AND DYNO SERVICE www.mustangmuscleonline.com |
|
|
|
|
09-07-2006, 11:43 PM
|
#6 |
|
show me my opponent
Join Date: Sep 2006
Location: El Paso Texas
Posts: 12
|
Re: Anyone running a C-4 tranny I need HELP!!!!!!!!
hey I have a question since you seemed to have figured out your problem, were converting this 93 coupe 4 cyl to a 351w swap, I'm going to run a c-4 tranny and i have the true dual cross member so the bushing housings are not welded yet, from what I read I guess it will bolt up fine then I weld it, but beyond that, did your driveshaft fit right? and was the slip yoke the right splines?
|
|
|
|
 |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Yet another tranny fluid ?? | Simi Stang | Windsor Power | 4 | 09-30-2003 12:44 PM |
| Tranny and rear end q | Nixon1 | Windsor Power | 0 | 02-21-2003 02:06 PM |
| Tranny update...Lentech VB | silver_pilate | Blue Oval Lounge | 10 | 05-02-2002 12:34 PM |
| The Motor Runnning and then...........Tranny | Stang Runner | Windsor Power | 0 | 12-12-2001 01:48 PM |
| This is bad! Did my Uncle cause my Racing tranny to overheat?(It's a long 1... sorry) | Stang_ROTY | Windsor Power | 1 | 08-30-2001 10:55 PM |