© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
|
06-20-2003, 01:16 AM | #1 |
Registered Member
Join Date: May 2003
Location: ontario.canada
Posts: 9
|
shifter vibration
my shifter vibrates out of gear or in any gear.
it get's worse with the higher rpm too. I can't go past 75mph because I'm afraid that the tranny is going to drop. I took it out of gear and let it coast and it's still vibrating pretty bad. right now I'm preparing for the worse ,from the balancer right down to the u-joint. I'm gonna start with the transmission mount then have the drive shaft balanced then the balancer then the flywheel. any other suggestion(s) would be greatly appreciated.
__________________
Black 87 GT,K&N,underdrive pulleys, B&M ripper, 373's,saleen wing flowmasters |
06-20-2003, 02:30 AM | #2 |
Registered Member
Join Date: Aug 2002
Location: SanAntonio, Tx
Posts: 957
|
check your shifter bolts, check your bellhousing bolts.
replace your u-joints, if it's not it, your only out 25$ or so. then look at your balancer while the motor is running, make sure it isnt wobbling. oh yea, if it does it while the car is Not moving, it is your balancer im willing to bet.
__________________
X-Texas highway patrol ssp 1990 coupe - exploder Gt-40 iron heads, Explorer intake, 19 lber's. E-cam. crane 1.7 rollers. 190fp. 75mm maf. 65mm tb, tubular subframe connectors, mac cai, Asp crank pulley, T-5, king cobra clutch, flowtech 1-5/8 unequals, mac X-pipe Frpp driveshaft, lakewood Lca's. race weight 3,160 12.69 @ 107.35, 1.71 60' 26x8.5 drag's 3.90 gear 13.20 @ 106.91 - 235/60/15 firestones 2.3 60' 3.27 gear |
06-20-2003, 12:03 PM | #3 |
2 Stangs in the Stable
Join Date: Apr 2002
Location: Baytown, TX
Posts: 1,209
|
Have your tires balanced also. There are so many things that could cause a vibration in your stick. I'd say between what you and Coupe50h have suggested, you've got a good place to start.
__________________
'90 GT Under construction Best E.T. = Fast @ High Speeds - OK So I Lie. So What!!! 04 F-150 STX 4.2L 5 spd Rice Haters Club Member #128 |
06-20-2003, 08:45 PM | #4 |
Registered Member
Join Date: Feb 2002
Location: New Jersey
Posts: 11
|
I had the same problem at one point, she would vibrate at excessive speeds, in or out of gear. Beleive it or not, my clutch was at fault. I swore that my tranny was going to go flying too. My clutch eneded up being extremley worn even though she caught low to the floor. As soon as I replaced it, everything went away and she was back to normal. I assume you have a stick because you metioned a flywheel instead of a flex plate. I hope this helps a little.
Good Luck, Christina |
06-22-2003, 09:05 PM | #5 |
Registered Member
Join Date: May 2003
Location: ontario.canada
Posts: 9
|
well I've checked the motor mount , crank pulley, and the trans mount they all looked fine, and everything seems to be tight.
The clutch was new when i bought it 30k's ago and I've had the flywheel resurfaced (i've had the tranny replaced also) I think I'm gonna get an aluminum driveshaft and have the u-joint replaced. and if it still vibrates I'll get a new clutch and new flywheel.
__________________
Black 87 GT,K&N,underdrive pulleys, B&M ripper, 373's,saleen wing flowmasters |
06-23-2003, 12:52 AM | #6 |
Registered Member
Join Date: Apr 1999
Location: greenwood, ar
Posts: 118
|
what kinda of aluminum driveshaft are you gona get? I think they all come with the u-joints already installed and you just bolt it up. That is the way my FMS aluminum driveshaft came.
__________________
'89 GT K&N, Twisted Wedge heads, TFS intake,FMS 1.7 rockers, Trick Flow stage 1 cam(221*/225* .530in\.542in) , 3.73's, headers, off road H-pipe, Flowmasters, FMS Clutch, Tremec, PRO-5.0, FMS driveshaft, fluidyne alum. radiator, and more to come. |
06-23-2003, 05:19 AM | #7 |
Registered Member
Join Date: May 2003
Location: ontario.canada
Posts: 9
|
wow 2 birds with one stone.
I'm not too picky about it I'll take whatever my local mustang shop have.
__________________
Black 87 GT,K&N,underdrive pulleys, B&M ripper, 373's,saleen wing flowmasters |
06-23-2003, 05:17 PM | #8 |
Registered Member
Join Date: May 2003
Location: ontario.canada
Posts: 9
|
turned out to be the u-joint.
she runs like a charm again.!!!
__________________
Black 87 GT,K&N,underdrive pulleys, B&M ripper, 373's,saleen wing flowmasters |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
No Need for Aftermarket Shifter after this Mod !! | Katmandu | Windsor Power | 6 | 03-24-2004 06:07 PM |
what would you ask for for christmas?? | lx5091 | Windsor Power | 28 | 11-22-2002 10:52 AM |
Vibration in shifter | skiwesser | Windsor Power | 2 | 08-18-2001 07:18 AM |
Vibration from shifter @ high-rpm's in 3rd+ gears only !! | jetuomi | Windsor Power | 14 | 07-18-2001 07:16 PM |
Vibration thru vehicle when accelerator is pressed | race1now | Windsor Power | 1 | 01-22-2001 12:28 AM |