AOD to T5 Conversion

88coupe · 07-18-2002, 03:18 PM

Okay I know this has been asked before.... But do you guys know any good sites that have a list of all the parts I need. ( I mean like all...small, small parts) So far I've got a Tranny, bellhousing, clutch, pedal assembly, flywheel, shifter boot lined up.... what else am I going to need? Thanks all!

Sonics2042 · 07-18-2002, 04:07 PM

T-5 Transmission
T-5 Clutch Fork - 86-93
1987-1993 Pedal Assembly
Aluminum Foot Pedals
Bellhousing
Clutch - 10 1/2"
Flywheel - for 10 1/2" Clutch
Flywheel Bolts
Transmission to Block Plate
Shifter
Shift Boot, Knob, Handle, Noise Barrier Weather Boot Gasket
Clutch Quadrant and Adjuster
Clutch Cable
T-5 Backup Wire Harness
Speedometer Gear to match your Gears
Pilot Bearing
Bellhousing Bolts (You can only use 2 of your AOD ones)
Pressure Plate Bolts
Clutch Cable Retainer Clip
Replacement T-5 Tail Shaft Seal
Steel Bearing Retainer
Aluminum Drivesaft (Optional)

Some of the stuff will be sold together...but here is hte list of stuff I bought.

Thanks,
DoranW

fiveohpatrol · 07-18-2002, 07:11 PM

Quote:

Bellhousing Bolts (You can only use 2 of your AOD ones)

no you can use 4 of the AOD ones, and you can use all 6 if you take up the space in the upper 2 with washers. Thats what I did in my swap.

When I get home, I'll post a link with a list of all the parts needed as well as step by step instructions on the swap.

The only thing I can see thats missing from Sonics2042's list is the automatic tranny fluid that you'll need

ByrdPE · 07-19-2002, 01:35 PM

Go here:http://www.wcfords.com/articles/tech/t5swap/t5swap.html
This is the site I used for the swap.
Good Luck!!

88coupe · 07-19-2002, 05:37 PM

Thanks guys, just what I was looking for!

fiveohpatrol · 07-20-2002, 01:16 AM

thats the exact link that I was gonna post

good luck with it, it is WELLLLLL worth the work

07-18-2002, 03:18 PM	#1
88coupe Registered Member Join Date: Jun 2002 Location: Norman, Oklahoma Posts: 64	AOD to T5 Conversion Okay I know this has been asked before.... But do you guys know any good sites that have a list of all the parts I need. ( I mean like all...small, small parts) So far I've got a Tranny, bellhousing, clutch, pedal assembly, flywheel, shifter boot lined up.... what else am I going to need? Thanks all! __________________ 88' Texas Highway Patrol. 5-Speed Conversion (FINALLY!) 97 Cobra Wheels, 3.73's, 2.5 H-Pipe (no cats), Spintech Pro Street Mufflers, 5 Lug Conversion (Moser 28 spline axles, FMS rotors), Hurst Billet Shifter and a Dirty K@N. 13.7@99.3

07-18-2002, 04:07 PM	#2
Sonics2042 Registered Member Join Date: Jul 2001 Location: Seattle, WA Posts: 381	T-5 Transmission T-5 Clutch Fork - 86-93 1987-1993 Pedal Assembly Aluminum Foot Pedals Bellhousing Clutch - 10 1/2" Flywheel - for 10 1/2" Clutch Flywheel Bolts Transmission to Block Plate Shifter Shift Boot, Knob, Handle, Noise Barrier Weather Boot Gasket Clutch Quadrant and Adjuster Clutch Cable T-5 Backup Wire Harness Speedometer Gear to match your Gears Pilot Bearing Bellhousing Bolts (You can only use 2 of your AOD ones) Pressure Plate Bolts Clutch Cable Retainer Clip Replacement T-5 Tail Shaft Seal Steel Bearing Retainer Aluminum Drivesaft (Optional) Some of the stuff will be sold together...but here is hte list of stuff I bought. Thanks, DoranW __________________ What I have: 1990 Red Mustang 5.0 LX: [BBK X-Pipe]-[MAC Cat-Back Exhaust] [MAC Cold Air Intake]-[BBK Equal Shorties] [3.55 Gears]-[Cobra Intake Manifold (Upper and Lower] [E-303 Cam]-[Granetelli Mass Air Flow Sensor] [Front and rear sway bars]-[New black carpet and seats.] [Adjustable Fuel Regulator]-[T5 Conversion w/ K. Cobra Clutch/Hurst STS] [Cobra Throttle Body]-[130A Alt. Conversion] Thinking about: Aftermarket Heads! Vortech A-Trim

07-19-2002, 01:35 PM	#4
ByrdPE Registered Member Join Date: Dec 1998 Location: MEMPHIS,TN. Posts: 36	Go here:http://www.wcfords.com/articles/tech/t5swap/t5swap.html This is the site I used for the swap. Good Luck!! __________________ Moroso cold air,FMS 373,KYB shocks/struts,Mac u/d Pullies,BBK sub frame connectors,3 core HD Modine radiator,T-5 swap,MAC Racer's choice shifter,FMS HD clutch, FMS 65mm TB/EGR,75mm Bullet PST performance sway-bar kit Maximum motorsports LCA's,Maximum Motorsports strut tower brace Maximum Motorsports G-load brace Auto meter H2O,oil,volt,vacuum/boost gauge assy. BBK 1 5/8 ceramic headers,custom cat H-pipe,HPM driveshaft loop, FMS aluminum D/S,3G alt. PPI Fan clutch/H2O pulley MSD6AL,MSD Blaster coil 'Tiny Avenger'intake pipe AOD to T-5 swap completed 7-14-02

07-19-2002, 05:37 PM	#5
88coupe Registered Member Join Date: Jun 2002 Location: Norman, Oklahoma Posts: 64	Thanks guys, just what I was looking for! __________________ 88' Texas Highway Patrol. 5-Speed Conversion (FINALLY!) 97 Cobra Wheels, 3.73's, 2.5 H-Pipe (no cats), Spintech Pro Street Mufflers, 5 Lug Conversion (Moser 28 spline axles, FMS rotors), Hurst Billet Shifter and a Dirty K@N. 13.7@99.3

07-20-2002, 01:16 AM	#6
fiveohpatrol I'd rather be basketweaving Join Date: Feb 2000 Location: Indianapolis Posts: 2,551	thats the exact link that I was gonna post good luck with it, it is WELLLLLL worth the work __________________ NMRA O/C 9516 NA pumpgas stickshift 347 10.65@125.6, 6.73@100, 1.41 60ft

Thread Tools
Show Printable Version Email this Page
Display Modes	Rate This Thread
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode	Rate This Thread:

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
5 lug conversion	stanger9219	Windsor Power	2	02-25-2004 11:31 PM
What all do you need to do rear disc conversion w/ SN95 Parts	KG88GT	Windsor Power	1	07-29-2003 01:45 PM
questions about maf conversion	spankaveli	Windsor Power	10	10-19-2002 02:46 PM
5 to 4 lug conversion	mike_navigator	Blue Oval Lounge	7	08-14-2002 11:17 PM
mass air 87GT conversion	greydan	Windsor Power	3	01-02-2002 07:57 PM