Will this COMBO run me 11's from running 14.20??

Rick 91GT · 09-26-2001, 08:03 AM

I agree don't mill the heads if you want to use stock pistons, if you mill them go to 58cc and notch your factory pistons and get a custom cam. My AFM cam made a huge difference in my motor and I made a device very similar to the TEA so I could fly cut the pistons while still in the block. They rent it for $50 plus shipping.

Look at my mods: The car should go 11's with cool weather and with the 4:30's that the cam is ground for I am hoping for 11.50's when it is all said and done. I am going to a set of 30# injectors and a 75mm TB as well. My car weighs 3170 with me, and it is doesn't have the back seat because of the way my cage is with a X brace to the shock towers.

If you stay with the Automatic you are going to need a lot more stall, I like Sky's idea about a 5 spd, that would make it easier.

------------------
Check Out My Site 91GT,Holley SysteMAX II Kit-Heads 2.02" x 1.60" port matched to a 1262,Anderson N-61,24#,76mm C&L,Full MAC, No A/C or PS or emissions, 12" K&N Filter,RNH PERFORMANCE Ram Air,Ron Davis Radiator,Full Suspension, SPEC stage III clutch, Lakewood SFI bell, S&W 8pt "X" brace,JAZ seats,3:73's,Welds..etc,4:30's and 31 splines coming very soon!
<B>12.16 @ 113.5, 1.78 60ft..no traction in the 90 degree

[This message has been edited by Rick 91GT (edited 09-26-2001).]

[This message has been edited by Rick 91GT (edited 09-26-2001).]

Thread Tools
Show Printable Version Email this Page
Display Modes	Rate This Thread
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode	Rate This Thread:

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
New combo, anyone else running this??	rwhite65	Classic Mustangs	13	01-18-2003 12:15 AM
Small block Combo ??'s	Coupe Devil	Windsor Power	8	12-06-2002 12:17 AM
Possible new combo, anyone running similar?	885.0L	Windsor Power	2	09-28-2002 05:36 PM
Car's running hot...	Sonics2042	Windsor Power	8	07-16-2002 04:50 PM
New combo is up and running (just not idling) !!!	cojonepony	Windsor Power	3	07-30-2001 04:52 PM

09-26-2001, 08:03 AM	#1
Rick 91GT Procharged! Join Date: May 1999 Location: Hanover, PA Posts: 1,539	I agree don't mill the heads if you want to use stock pistons, if you mill them go to 58cc and notch your factory pistons and get a custom cam. My AFM cam made a huge difference in my motor and I made a device very similar to the TEA so I could fly cut the pistons while still in the block. They rent it for $50 plus shipping. Look at my mods: The car should go 11's with cool weather and with the 4:30's that the cam is ground for I am hoping for 11.50's when it is all said and done. I am going to a set of 30# injectors and a 75mm TB as well. My car weighs 3170 with me, and it is doesn't have the back seat because of the way my cage is with a X brace to the shock towers. If you stay with the Automatic you are going to need a lot more stall, I like Sky's idea about a 5 spd, that would make it easier. ------------------ Check Out My Site 91GT,Holley SysteMAX II Kit-Heads 2.02" x 1.60" port matched to a 1262,Anderson N-61,24#,76mm C&L,Full MAC, No A/C or PS or emissions, 12" K&N Filter,RNH PERFORMANCE Ram Air,Ron Davis Radiator,Full Suspension, SPEC stage III clutch, Lakewood SFI bell, S&W 8pt "X" brace,JAZ seats,3:73's,Welds..etc,4:30's and 31 splines coming very soon! <B>12.16 @ 113.5, 1.78 60ft..no traction in the 90 degree [This message has been edited by Rick 91GT (edited 09-26-2001).] [This message has been edited by Rick 91GT (edited 09-26-2001).]