4.6 SOHC vs 4.6 DOHC bolt pattern ?

rj3e5 · 10-11-2001, 05:27 PM

Will a t-5 hook up to a cobra motor.
I am working on a cobra motor swap, and got a t-5 for almost free w/ 200 miles on it. I do not care if the t-5 will last forever, just long enough untill I can get a 45 or 56 tranny.

Mustang92 · 10-12-2001, 04:20 PM

The input shaft is different it won't work.

Bill

------------------
00 GT, MAC Offroad H, Steeda Pulleys & Timing Adjuster, C&L 80mm, 4.30’s, Flows w/turndowns, UPR shifter, UPR Pro Series LCA’s, Lakewood 70/30’s & 50/50’s, 253.8 RWHP/292.8RWTQ
Best ET 12.91
Best MPH 105.49
M/M 100, 7085
2001 Mod Motor Shootout 2V NA Champion

rj3e5 · 10-12-2001, 07:04 PM

the input shaft is diffrent how?
to long to short, diffrent # of splines?

Minus the input shaft, will it bolt up?

rj3e5 · 10-16-2001, 07:55 PM

Mustang92 · 10-17-2001, 11:11 AM

Pretty sure the bellhousing will bolt up but I don't know the specifics I've heard it mentioned a few times on some of the other boards. Input shaft I believe it too short. Personally I can't imagine why you would put such a garbage tranny as a T-5 behind the motor. I've used both for years and the T-5 is much worse.

Bill

rj3e5 · 10-17-2001, 06:06 PM

yes the t-5 is worse, but when I got a brand new (less than 500 miles on it) t-5 for $200 I can not complain.

It is just for the time being untill I can get a better one.

10-11-2001, 05:27 PM	#1
rj3e5 Registered Member Join Date: Oct 2001 Location: el cajon, ca, usa Posts: 5	4.6 SOHC vs 4.6 DOHC bolt pattern ? Will a t-5 hook up to a cobra motor. I am working on a cobra motor swap, and got a t-5 for almost free w/ 200 miles on it. I do not care if the t-5 will last forever, just long enough untill I can get a 45 or 56 tranny.

10-16-2001, 07:55 PM	#4
rj3e5 Registered Member Join Date: Oct 2001 Location: el cajon, ca, usa Posts: 5	Bump

Thread Tools
Show Printable Version Email this Page
Display Modes	Rate This Thread
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode	Rate This Thread:

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Bolt Pattern for '99 Mustang - Help	antoine24	Blue Oval Lounge	3	07-02-2004 10:12 PM
bolt pattern	MATTKNIGHT	Windsor Power	1	10-12-2003 09:10 AM
need help measuring torque converter bolt pattern	82 GT	Windsor Power	0	06-17-2003 03:38 PM
Bolt pattern adapters?	66StangGuy	Classic Mustangs	0	09-16-2002 02:04 AM
SOHC to DOHC conversion?	Red94Z	Modular Madness	6	11-06-2000 04:43 AM

10-12-2001, 04:20 PM	#2
Mustang92 Drag Racer! Join Date: Nov 1999 Location: Lake Worth, FL USA Posts: 757	The input shaft is different it won't work. Bill ------------------ 00 GT, MAC Offroad H, Steeda Pulleys & Timing Adjuster, C&L 80mm, 4.30’s, Flows w/turndowns, UPR shifter, UPR Pro Series LCA’s, Lakewood 70/30’s & 50/50’s, 253.8 RWHP/292.8RWTQ Best ET 12.91 Best MPH 105.49 M/M 100, 7085 2001 Mod Motor Shootout 2V NA Champion

10-12-2001, 07:04 PM	#3
rj3e5 Registered Member Join Date: Oct 2001 Location: el cajon, ca, usa Posts: 5	the input shaft is diffrent how? to long to short, diffrent # of splines? Minus the input shaft, will it bolt up?

10-17-2001, 11:11 AM	#5
Mustang92 Drag Racer! Join Date: Nov 1999 Location: Lake Worth, FL USA Posts: 757	Pretty sure the bellhousing will bolt up but I don't know the specifics I've heard it mentioned a few times on some of the other boards. Input shaft I believe it too short. Personally I can't imagine why you would put such a garbage tranny as a T-5 behind the motor. I've used both for years and the T-5 is much worse. Bill

10-17-2001, 06:06 PM	#6
rj3e5 Registered Member Join Date: Oct 2001 Location: el cajon, ca, usa Posts: 5	yes the t-5 is worse, but when I got a brand new (less than 500 miles on it) t-5 for $200 I can not complain. It is just for the time being untill I can get a better one.