03 cobra Hopup parts

Doug McGinn · 07-28-2002, 04:45 PM

I need help locating the following parts for a 2003 Cobra.
Any links you can send me or post would be greatly appreciated.

1. Blower pulley
2. Catback Exhaust system (not steeda)
3. H pipe
4. Cold Air Intake setup
5. Performance chip
6. Drag Radials (current tires are 275/40zr17)

Also i was wondering how the steeda exhaust systems compare to others like Flowmaster and MAC as far as horsepower and sound.What are the effects of using an offroad H pipe without Convertors or potential problems?

My Email is RedCobra@cox.net

VeNuM · 07-28-2002, 05:19 PM

1. try using a SVT Lightning pulley
4. http://www.uprproducts.com/shopping/shopexd.asp?id=371
If you don't run cats, you will get better performance and a louder, deeper sounding exhaust. Only thing is you can't pass emissions.

Doug McGinn · 07-28-2002, 05:27 PM

problem with using the lightning pulley is theres no way of knowing what your final boost figure is going to be.
I dont wanna spend 200 bucks on a pulley and then blow the heads off my engine.

VeNuM · 07-29-2002, 03:44 PM

Try these guys then, http://www.southfloridapulleyhq.com

46stang · 07-29-2002, 10:19 PM

i just installed the south florida pulley system on my car and wow it pulls much harder now! I'm going to try and get a dyno tune this friday! it feels like a 75 shot of nos!! i really doubt you'll blow the heads off a motor with 8.5 to 1 compression but the cool thing about the south florida pulley system is you can get different size pullies! so if you don't want too much boost no problem just pick a bigger pulley

i went with the lightning size but thats just me. good luck

Leon

Doug McGinn · 07-31-2002, 01:29 AM

what tool did you use to remove the old pulley and then install the new one?
How much total boost are you getting from the pulley you bought?

46stang · 07-31-2002, 09:21 AM

i had a puller at my work. it is similar to the one on south florida pulleys website. they sell the tool as well!! it's actually a pretty easy swap. my stock guage gets buried past the 10lb mark. i need to get an aftermarket guage for it! most of the guys i've talked to are getting 12-12.5lbs total boost. If your worried just get one of the bigger pullies for the street and then when you go to the track you could put a smaller one on! the cool thing is that pullies are easily swapable with there system!check out this site:

svtperformance.com

lots of good info on our cars there

my buddy has a 03 cobra and i took him for a ride in mine! he is ordering some pullies for his this week!! he was very impressed

good luck.
Leon

07-28-2002, 04:45 PM	#1
Doug McGinn Registered Member Join Date: May 2002 Location: Nebraska Posts: 63	03 cobra Hopup parts I need help locating the following parts for a 2003 Cobra. Any links you can send me or post would be greatly appreciated. 1. Blower pulley 2. Catback Exhaust system (not steeda) 3. H pipe 4. Cold Air Intake setup 5. Performance chip 6. Drag Radials (current tires are 275/40zr17) Also i was wondering how the steeda exhaust systems compare to others like Flowmaster and MAC as far as horsepower and sound.What are the effects of using an offroad H pipe without Convertors or potential problems? My Email is RedCobra@cox.net

07-28-2002, 05:19 PM	#2
VeNuM Registered Member Join Date: Apr 2002 Location: Downers Grove, IL Posts: 464	1. try using a SVT Lightning pulley 4. http://www.uprproducts.com/shopping/shopexd.asp?id=371 If you don't run cats, you will get better performance and a louder, deeper sounding exhaust. Only thing is you can't pass emissions. __________________ 1989 Black Mustang GT Hatchback, Underdrive Pulles, Electric Fan, Cold Air Intake, Headers, Offroad H-Pipe, Magnaflow catback, Steeda Tri-Ax, Fluidyne Aluminum Radiator, Timing at 14*, 3.73's Coming not so soon: 408w Ricer Hater's Club Member #59

07-29-2002, 03:44 PM	#4
VeNuM Registered Member Join Date: Apr 2002 Location: Downers Grove, IL Posts: 464	Try these guys then, http://www.southfloridapulleyhq.com __________________ 1989 Black Mustang GT Hatchback, Underdrive Pulles, Electric Fan, Cold Air Intake, Headers, Offroad H-Pipe, Magnaflow catback, Steeda Tri-Ax, Fluidyne Aluminum Radiator, Timing at 14*, 3.73's Coming not so soon: 408w Ricer Hater's Club Member #59

07-29-2002, 10:19 PM	#5
46stang Registered Member Join Date: May 1999 Location: moorpark ca Posts: 340	i just installed the south florida pulley system on my car and wow it pulls much harder now! I'm going to try and get a dyno tune this friday! it feels like a 75 shot of nos!! i really doubt you'll blow the heads off a motor with 8.5 to 1 compression but the cool thing about the south florida pulley system is you can get different size pullies! so if you don't want too much boost no problem just pick a bigger pulley i went with the lightning size but thats just me. good luck Leon __________________ 03 sonic blue cobra coupe, 11.49@122mph bakerfield raceway! 11.67@120mph fontana 98 GT, stock for now.

07-31-2002, 09:21 AM	#7
46stang Registered Member Join Date: May 1999 Location: moorpark ca Posts: 340	i had a puller at my work. it is similar to the one on south florida pulleys website. they sell the tool as well!! it's actually a pretty easy swap. my stock guage gets buried past the 10lb mark. i need to get an aftermarket guage for it! most of the guys i've talked to are getting 12-12.5lbs total boost. If your worried just get one of the bigger pullies for the street and then when you go to the track you could put a smaller one on! the cool thing is that pullies are easily swapable with there system!check out this site: svtperformance.com lots of good info on our cars there my buddy has a 03 cobra and i took him for a ride in mine! he is ordering some pullies for his this week!! he was very impressed good luck. Leon __________________ 03 sonic blue cobra coupe, 11.49@122mph bakerfield raceway! 11.67@120mph fontana 98 GT, stock for now.

07-28-2002, 05:27 PM	#3
Doug McGinn Registered Member Join Date: May 2002 Location: Nebraska Posts: 63	problem with using the lightning pulley is theres no way of knowing what your final boost figure is going to be. I dont wanna spend 200 bucks on a pulley and then blow the heads off my engine.

07-31-2002, 01:29 AM	#6
Doug McGinn Registered Member Join Date: May 2002 Location: Nebraska Posts: 63	what tool did you use to remove the old pulley and then install the new one? How much total boost are you getting from the pulley you bought?

Thread Tools
Show Printable Version Email this Page
Display Modes	Rate This Thread
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode	Rate This Thread:

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
2003 Cobra Buyer Beware!!	Doug McGinn	Modular Madness	16	07-25-2002 08:26 AM
2003 Cobra Parts	Doug McGinn	Modular Madness	6	07-16-2002 06:23 PM
Buddy Just Bought a 98 Cobra.....	INVINCISTANG	Stang Stories	10	06-25-2002 01:36 PM
What's the difference between 95 GT and 95 Cobra?	Ron Brooks	Blue Oval Lounge	5	07-13-2001 12:56 PM
Cobra Computer	Bangin Gears	Windsor Power	1	04-30-2001 02:38 AM