Looking for combo suggestions...

NOphonyponys · 06-13-2001, 02:31 PM

Looking for best known combos! I need the ultimate stroker package that is a availble. Just imagine... if you had $6000 in your hand, what motor would you drop into YOUR Stang??!! I want the strongest wheel pullin', head jerkin', tire smokin', MONSTER I can drop into my 94 GT.
Here's my current setup:
324.5RWHP+334RWFTLBS
* Anderson STAGE 2 ported Edelbrock Performer intake (~285CFM)
* Anderson STAGE 2 TFS Heads (283CFM INT/179CFM EXT)
* Pullys
* MSD 6AL + MSD coil
* 75mm BBK Throttle Body
* 80mm Grenatelli MAF
* MAC Cold-Air induction
* 24lb injectors
* Anderson B2 cam
* Anderson PMS computer (tuned by Anderson)
* 1.6 full roller rockers
* MAC H-Pipe
* No cats w/Hooker mufflers
* Tremec 3550
* Alum. Driveshaft
* 3.73 gears w/stock axles
* In-tank 255GPH BBK fuel pump

Probably a few other things I can't recall right now... but the ONE thing you DON'T SEE above is a modified botttom end. Unfortunately, its a bone-stock bottom end! This is where I need everyone's assistance...

Any suggested web pages I could check out, suggested engine builders, or any other advise is welcome! PLEASE HELP! I need to get this damn car into the 11's!

Thanks again guys and gals!

------------------
ONLY 325 RWHP??? DAMN...

Shawn · 06-13-2001, 06:39 PM

How much money do you have to spend...=) hehe...R302-billet crank-billet rods.ahh wish I had that! Where are you located, I know a few great engine builders in the Illinois region, email me if your in this area. Rurockn@aol.com Otherwise the new Sportsman 302 block looks like a nice setup for the new year! Run one with 4340 internals and pull some power in the top end without any worries!

06-13-2001, 02:31 PM	#1
NOphonyponys Registered Member Join Date: Jun 2001 Posts: 11	Looking for combo suggestions... Looking for best known combos! I need the ultimate stroker package that is a availble. Just imagine... if you had $6000 in your hand, what motor would you drop into YOUR Stang??!! I want the strongest wheel pullin', head jerkin', tire smokin', MONSTER I can drop into my 94 GT. Here's my current setup: 324.5RWHP+334RWFTLBS * Anderson STAGE 2 ported Edelbrock Performer intake (~285CFM) * Anderson STAGE 2 TFS Heads (283CFM INT/179CFM EXT) * Pullys * MSD 6AL + MSD coil * 75mm BBK Throttle Body * 80mm Grenatelli MAF * MAC Cold-Air induction * 24lb injectors * Anderson B2 cam * Anderson PMS computer (tuned by Anderson) * 1.6 full roller rockers * MAC H-Pipe * No cats w/Hooker mufflers * Tremec 3550 * Alum. Driveshaft * 3.73 gears w/stock axles * In-tank 255GPH BBK fuel pump Probably a few other things I can't recall right now... but the ONE thing you DON'T SEE above is a modified botttom end. Unfortunately, its a bone-stock bottom end! This is where I need everyone's assistance... Any suggested web pages I could check out, suggested engine builders, or any other advise is welcome! PLEASE HELP! I need to get this damn car into the 11's! Thanks again guys and gals! ------------------ ONLY 325 RWHP??? DAMN...

Thread Tools
Show Printable Version Email this Page
Display Modes	Rate This Thread
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode	Rate This Thread:

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Harmonic Balancer Suggestions	jim_howard_pdx	Windsor Power	5	02-28-2008 11:32 AM
Timeslips attached/ need suggestions	Kamaro Killer	Blue Oval Lounge	18	12-04-2002 12:58 PM
Rookie upgrade"?" looking for suggestions and comments also I WTB parts if ne1 has em	Rusty45398	Windsor Power	9	11-21-2001 02:19 AM

06-13-2001, 06:39 PM	#2
Shawn Registered Member Join Date: Dec 1998 Location: Chicago, IL. USA Posts: 77	How much money do you have to spend...=) hehe...R302-billet crank-billet rods.ahh wish I had that! Where are you located, I know a few great engine builders in the Illinois region, email me if your in this area. Rurockn@aol.com Otherwise the new Sportsman 302 block looks like a nice setup for the new year! Run one with 4340 internals and pull some power in the top end without any worries!