2 questions

bailey_57 · 05-25-2004, 09:24 AM

question 1:
i'm trying to put my 1.6 roller rockers on. while taking the upper plenum off i got to the back and instead of being a bolt there was a stud with a nut. after removing the nut i felt what appeared to be a line of some sort. its stuck. what is it? and how do i get it off?

question 2: dipstick broke off. where is it located and can i take it off without removing the header? is there maybe and easy fix?

89 GT stock 5.0 HO

LX5liter · 05-25-2004, 02:05 PM

There should be a couple of vaccuum lines and the PCV valve at the back of the intake. The dipstick tube just goes into the oilpan and is sealed with an O-ring. Just undo the mount on the header and it should pull out if you give it a it of a twist at the same time.

Scrapla · 05-25-2004, 08:31 PM

I think your talking about that small metal bar that goes from that stud to the other side of the plenum, if you removed all the plenum nuts and bolts that bar should come off, I had to pry at mine a little.

PS On that stud I think its held on by a seperate nut, so theres 2 nuts one to remove the bar and one to remove the plenum

05-25-2004, 09:24 AM	#1
bailey_57 Registered Member Join Date: Mar 2000 Location: Berwick,Pa Posts: 127	2 questions question 1: i'm trying to put my 1.6 roller rockers on. while taking the upper plenum off i got to the back and instead of being a bolt there was a stud with a nut. after removing the nut i felt what appeared to be a line of some sort. its stuck. what is it? and how do i get it off? question 2: dipstick broke off. where is it located and can i take it off without removing the header? is there maybe and easy fix? 89 GT stock 5.0 HO

05-25-2004, 02:05 PM	#2
LX5liter dude5l Join Date: May 2001 Location: Grande Prairie, Alberta, Canada Posts: 603	There should be a couple of vaccuum lines and the PCV valve at the back of the intake. The dipstick tube just goes into the oilpan and is sealed with an O-ring. Just undo the mount on the header and it should pull out if you give it a it of a twist at the same time. __________________ Good luck! Brad R. 1992 L.X. 5.0 coupe MODS: A few little bolt ons New Best time ...11.60 @ 128 mph @ 2000+ ft altitude. Rice Haters Club member #39 Users rides #2542

05-25-2004, 08:31 PM	#3
Scrapla Registered Member Join Date: Apr 2002 Location: Florida Posts: 532	I think your talking about that small metal bar that goes from that stud to the other side of the plenum, if you removed all the plenum nuts and bolts that bar should come off, I had to pry at mine a little. PS On that stud I think its held on by a seperate nut, so theres 2 nuts one to remove the bar and one to remove the plenum __________________ 90gt 347 and some bolt ons :-) RICE HATERS MEMBER #73

Thread Tools
Show Printable Version Email this Page
Display Modes	Rate This Thread
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode	Rate This Thread:

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Just got a 98, have some questions?	98GTNewbie	Modular Madness	5	08-30-2003 12:41 AM
Quick questions on Explorer Intake install.	Falcons Talon	Windsor Power	2	08-21-2003 12:40 PM
Several questions about oil.	zepherman	Windsor Power	3	08-03-2002 06:59 AM
HELP! Newbie 95-96 GT questions	Ron Brooks	Blue Oval Lounge	7	07-11-2001 07:38 PM
S/R Questions	DAMION	Racer's Club House	1	09-30-1999 11:02 AM