© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
08-04-2001, 01:38 AM | #1 |
Registered Member
Join Date: Aug 2001
Location: Wisconsin, USA
Posts: 1
|
Looking for some ideas
I'm probably gonna buy my uncle's '91 Mustang 5.0 once I've earned enough money and I was wondering what some inexpensive mods would be to increase stuff like HP or accel. I'm pretty new to cars and I really only know stuff that has to do with appearance. Thanks for your help.
|
08-04-2001, 04:55 PM | #2 |
Moderator
Join Date: Sep 1998
Location: Grand Rapids, Michigan, USA
Posts: 1,001
|
Welcome to MustangWorks!!! Really what I have found to be the best method is just hang out here on the 'boards. Read everything and listen to everybody. There's several Mustang modification books on the market too. If you're new to working on cars (as in under-hood mechanical stuff), pick up a Haynes manual. I still refer to it myself time to time.
If you want biggest bang-for-the-buck parts, I think everyone here will tell you rear end gears are THE place to start. Closely following would be bumping the ignition timing (along with higher octane gas), getting a K&N air filter, and doing regular tuneups including oxygen sensors & PCV valve. After that it'll take heads, a cam, intake, exhaust, etc. Good luck in your quest for more power. ------------------ Capri306, Moderator, The Mustang Works Online 1979 Mercury Capri, 5.0L -- C4 -- 2.73 1987 Mustang LX Notch |
08-04-2001, 06:51 PM | #3 |
Registered Member
Join Date: Nov 2000
Location: Maple Ridge B.C. Canada, The Best Place In The World
Posts: 871
|
Remove The Air Silencer, Set TPS To .98, Bump Timing To Around 14*, Get 3.55/3.73 Gears, New Shifter (Dont Know If Its Stick).....
Good Luck!!! ------------------ 1988 Mustang GT, T-5 3.08's, No Smog Pump (Shorty Belt), Dumps At The End Of Stock H-Pipe, K&N Air Filter (Stock Air Box), Removed Air SilencerMy Stang My Site (Not Done Yet) |
08-05-2001, 02:39 PM | #4 |
Registered Member
Join Date: Jun 2001
Location: KC,Mo,US
Posts: 70
|
I started off with 3.73 gears, off road h-pipe, mufflers, and pulleys. K&N filter was already on it.
------------------ 95gt 80k, MSD 6AL, MSD coil, pulleys, fpr, cold air kit, off road h-pipe, flowmasters, 3.73, 9mm wires, mega bite jr lowers, kennybrown subframe connectors, edelbrock performer intake, 70mm TB, 73mm C&L, 24lb injectors Aluminum Driveshaft, Tri-Ax shifter. |
Thread Tools | |
Display Modes | Rate This Thread |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Ideas on removing a stubborn bolt? | Evil Joe | Windsor Power | 6 | 07-02-2003 07:59 PM |
Looking for idea's.... | mustang_sally65 | Appearance & Detailing | 3 | 09-29-2001 07:44 AM |
Holley ignition, coil, and distributor installed..car won't start. Any ideas? | chadtn2 | Windsor Power | 5 | 08-13-2001 01:13 AM |
performance ideas that work | 99' droptop | Modular Madness | 2 | 03-11-2000 12:18 PM |