Buying an 8.8" rear

Rick 91GT · 06-17-2001, 08:58 AM

I think new would be better, just because it's new, but many people use used parts. If your going to have the 9" ends put on so the seals dont leak you may want to look at the Superior axles supposedly they will not leak with the c-clip elims, and you should have the tubes straigtened and welded whilt is all apart. Currie does sell complete rears but it will cost you $2500 minimum. I getting ready to do my rear as well, but I am getting the Drivetrain DirectPackage that includes-31 spline Superiors, and a Eaton Posi $579, then re-using my stock housing which I will have welded and straightened if need be. All the new bearing run about $80 from D&D or Drivetrain Direct. www.drivetraindirect.com

------------------
Check Out My Site 91GT,Holley SysteMAX II Kit-Heads 2.02" x 1.60" port matched to a 1262,Anderson N-61,24#,76mm C&L,Full MAC exhaust 1-5/8" Long tubes,2-1/2" O.R H-Pipe,2 1/2" cat back, No A/C or PS or emissions, 12" K&N Filter,RNH PERFORMANCE Ram Air,Ron Davis Radiator,Full Suspension,S&W 8pt "X" brace,JAZ seats,3:73's,Welds..etc,4:30's and 31 splines coming very soon! FIRST TIME OUT 12.16@111 WHEELS-UP

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
new rear end	fordkid68	Classic Mustangs	18	11-24-2009 08:05 PM
want rear disk without changing overall length of rear....please help!!!	dragstang86	Windsor Power	1	07-31-2003 06:32 PM
installing cobra rear in my LX...picked up a totaled 93 limited edition	dragstang86	Windsor Power	1	05-26-2003 11:23 AM
Rear Brake Line Removal	Kisner	Classic Mustangs	2	03-13-2002 12:31 PM
Recall 01S15 Rear Knuckle replacement	folthoff	Special Production	0	05-02-2001 08:28 AM

06-17-2001, 08:58 AM	#2
Rick 91GT Procharged! Join Date: May 1999 Location: Hanover, PA Posts: 1,539	I think new would be better, just because it's new, but many people use used parts. If your going to have the 9" ends put on so the seals dont leak you may want to look at the Superior axles supposedly they will not leak with the c-clip elims, and you should have the tubes straigtened and welded whilt is all apart. Currie does sell complete rears but it will cost you $2500 minimum. I getting ready to do my rear as well, but I am getting the Drivetrain DirectPackage that includes-31 spline Superiors, and a Eaton Posi $579, then re-using my stock housing which I will have welded and straightened if need be. All the new bearing run about $80 from D&D or Drivetrain Direct. www.drivetraindirect.com ------------------ Check Out My Site 91GT,Holley SysteMAX II Kit-Heads 2.02" x 1.60" port matched to a 1262,Anderson N-61,24#,76mm C&L,Full MAC exhaust 1-5/8" Long tubes,2-1/2" O.R H-Pipe,2 1/2" cat back, No A/C or PS or emissions, 12" K&N Filter,RNH PERFORMANCE Ram Air,Ron Davis Radiator,Full Suspension,S&W 8pt "X" brace,JAZ seats,3:73's,Welds..etc,4:30's and 31 splines coming very soon! FIRST TIME OUT 12.16@111 WHEELS-UP