Ladder Bars?

Coupe Devil · 07-13-2001, 11:30 AM

Take into consideration this is all going on a Ranger. The rear will be cut behind the cab and new rails will be added. I was going to keep the factory frame rails but have since decided against it. I would like to get a 36" bar if possible. I am not wirried about location of muffs and such as all that will be routed around the rear as needed. I am also using the 9" rear out of a 75 lincoln because it is equipped with factory disc's. I will have it narrowed and be running Strange or Moser axles.

This IS NOT a drag truck. Just something to drive on the street mainly and take to the track occ. I want to have fun building and driving this truck. I'm not in a hurry so I am bascially doing a ground up like you Rustang. It will be equipped with an 8 point cage from CAchassisworks, and further modified and added to for bracing of the bed and rear clip. I bascally stripping everything factory off and replacing it all. the wiring for the lights, turn signals, wipers, and body will only remain factory. I am adding tubbs and a roll pan to the bed but other than that stock.

The interior will retain the stock dash with guages replaced using Autometer Ultralites. I am also using the seats out of my Mustang for this project.

------------------
'93 lx 4 banger, wrecked '90 lx 5.0, w/ t-5. .030 over fully ported and polihed (did that just to see if I could-first attempt at it). Motor and tranny in use for Ranger project.

Cocked, locked and ready to rock

Pony Power Forever

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
South Side Machines Lift Bars.....	cucho	Windsor Power	7	01-29-2004 10:51 PM
DO I need wheelie bars?	ciara	Windsor Power	4	12-16-2003 12:34 PM
Lakewood Lift Bars	LaxMan	Windsor Power	1	11-25-2002 09:25 AM
Lift bars for my 88 vert yes/no	Dark_5.0	Windsor Power	2	01-02-2002 07:43 PM
tracttion bars?	StripedStangLX	Blue Oval Lounge	6	01-27-2001 12:50 AM

07-13-2001, 11:30 AM	#6
Coupe Devil Moderator Join Date: Mar 2001 Location: Myrtle Beach SC Posts: 1,643	Take into consideration this is all going on a Ranger. The rear will be cut behind the cab and new rails will be added. I was going to keep the factory frame rails but have since decided against it. I would like to get a 36" bar if possible. I am not wirried about location of muffs and such as all that will be routed around the rear as needed. I am also using the 9" rear out of a 75 lincoln because it is equipped with factory disc's. I will have it narrowed and be running Strange or Moser axles. This IS NOT a drag truck. Just something to drive on the street mainly and take to the track occ. I want to have fun building and driving this truck. I'm not in a hurry so I am bascially doing a ground up like you Rustang. It will be equipped with an 8 point cage from CAchassisworks, and further modified and added to for bracing of the bed and rear clip. I bascally stripping everything factory off and replacing it all. the wiring for the lights, turn signals, wipers, and body will only remain factory. I am adding tubbs and a roll pan to the bed but other than that stock. The interior will retain the stock dash with guages replaced using Autometer Ultralites. I am also using the seats out of my Mustang for this project. ------------------ '93 lx 4 banger, wrecked '90 lx 5.0, w/ t-5. .030 over fully ported and polihed (did that just to see if I could-first attempt at it). Motor and tranny in use for Ranger project. Cocked, locked and ready to rock Pony Power Forever