Linear Mode
© Copyright 1995 thru 2008 - The Mustang Works™. All Rights Reserved.
MustangWorks.com is designed and hosted by Aero3 Media.
MustangWorks.com is designed and hosted by Aero3 Media.
02-23-2003, 10:14 PM
|
#1 |
|
Registered Member
Join Date: Aug 2001
Location: Woodlawn IL,USA
Posts: 62
|
Intake options for EFI 351
Does any aftermarket manufacture make an upper intake that fits directly on to the stock 1988 EFI truck intake? I was told the Holly unit will bolt up and is aligned correctly but is this correct or Bullshit? Any comments would be great....Thanks, GTNBY2
__________________
GTNBY2 getin' by 2!! 351W, 30 over, Comp Cams XE274h, Trick Flow Street Heat intake, AFR185 heads, 70mm TB, 80mm Mass, 24lb inj, Moroso cold air kit, BBK 1 5/8" unequal length headers, 2 1/2" off road X-pipe, 40 series Flowmasters |
|
|
|
02-24-2003, 07:40 AM
|
#2 |
|
Registered Member
Join Date: Aug 2000
Location: Wisconsin
Posts: 879
|
im pretty sure edelbrock dose..check out there site www.edelbrock.com
__________________
'91 GT,410W,10.5 to 1 comp,Victor Jr. heads,Victor 5.8 intake,FTI cam,Crane retro fit lifters,Scorpian 1.6 RR's,Melling HV oil pump,MSD distro.,Canton oil pan,FMS flywheel,Romac balancer,FMS timing chain,Accufab 90mm TB,C&L 76mm maf, 42lbers,HD clutch,K&N air filter,Mac long tubes,Pro dumps,powerchamber,FMS 9mm wires,180 thermostat,Ford Racing gauges,5inch Tach,centerline convo pro's,nitto DR's,Pro3i lower control arms,50/50 shocks,3.55 gears,TFS HD diff. cover Next year: Tremec TKO,Spec stage 3 clutch,alum driveshaft,complete fuel system www.angelfire.com/linux/demondan |
|
|
|
|
02-24-2003, 01:35 PM
|
#3 |
|
Registered Member
Join Date: Oct 2000
Location: Ontario canada
Posts: 446
|
Bennet Cartech boxxed uppers
__________________
89 with 331 t3'/t4 hybrids. upr Suspention worked out finnaly . 9.89 144 mph . |
|
|
|
|
02-24-2003, 06:20 PM
|
#4 |
|
Registered Member
Join Date: Jan 2001
Location: Surrey, BC, Canada
Posts: 19
|
the holly intake should bolt right up to it. the mounts will be in the same position but who knows until you try right??? On the holly the ports are the same design but I dont know about port size
|
|
|
|
 |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Trick Flow intake problems | shacar87 | Windsor Power | 9 | 11-14-2003 05:53 PM |
| Intake selection with a 383/408 stroker | Capri306 | Windsor Power | 12 | 05-03-2002 10:12 PM |
| Explore intake??????????? | William Bowers | Windsor Power | 2 | 02-14-2002 10:27 PM |
| HELP!!! oil in intake, what to do?? | bosco | Windsor Power | 4 | 02-03-2002 05:02 PM |
| Edelbrock spec's and intake question?? | jerryIII | Windsor Power | 0 | 05-24-2001 12:49 PM |