speedo off with gears!

MEDIK418 · 03-10-2003, 12:20 AM

It'll cost you about 7 bucks and about 20 minutes of easy work and half that is getting the car up on the jackstands. Any Ford house should have what you need. and thier price is the same. . about 7 dollars.
About 3/4 of the way down the left (driver) side of the transmission is a cable about 1/2 inch in diameter that goes into the transmission tail housing at a 45 degree angle. I'm assuming you have a t5. Auto's are pretty much the same. The cable is about where the transmission crossmember sits and is actually above it enough that it sometimes makes it tough to get hold of. Patience and lots of tugging and it'll come out. There should be a horseshoe shaped clip that goes halfway around the cable's metal end piece. Looks and acts like a distributor hold down clamp. It is held in place by a small bolt that goes into the tailhousing just behind the cable. I think it's a 10 mm head. Remove the bolt, pull the clip back and it will fall off in your hand. Pull the cable end piece out of the transmission and the gear you need to change is on the end of this cable. Pull it off and push on the new one and reverse the procedure to reinstall it.

03-10-2003, 12:20 AM	#4
MEDIK418 Registered Member Join Date: Mar 1999 Location: Amarillo, Texas, USA Posts: 780	It'll cost you about 7 bucks and about 20 minutes of easy work and half that is getting the car up on the jackstands. Any Ford house should have what you need. and thier price is the same. . about 7 dollars. About 3/4 of the way down the left (driver) side of the transmission is a cable about 1/2 inch in diameter that goes into the transmission tail housing at a 45 degree angle. I'm assuming you have a t5. Auto's are pretty much the same. The cable is about where the transmission crossmember sits and is actually above it enough that it sometimes makes it tough to get hold of. Patience and lots of tugging and it'll come out. There should be a horseshoe shaped clip that goes halfway around the cable's metal end piece. Looks and acts like a distributor hold down clamp. It is held in place by a small bolt that goes into the tailhousing just behind the cable. I think it's a 10 mm head. Remove the bolt, pull the clip back and it will fall off in your hand. Pull the cable end piece out of the transmission and the gear you need to change is on the end of this cable. Pull it off and push on the new one and reverse the procedure to reinstall it. __________________ 1986 four-eyed LX coupe, 358 Cleveland, Tremec TKO600/centerforce clutch, dish cut Probe forged pistons, comp cams hyd.roller cam, .579/.588@224/230, Edel.performer, 670 holley street avenger, CPR custom built long tubes, ported and polished 4bbl heads, manley valves, beehive springs, MSD peo-billet dist/MSD6AL, fluidamper, 5 lug conv. with 17x8 bullits there's more but it's still not finished yet. Oh, and the oldest boy is turning his 89 GT into a FFR cobra this next summer. Last edited by MEDIK418; 03-10-2003 at 12:27 AM..

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Speedo Gears for 3.73??	89GTimporteater	Windsor Power	4	04-05-2003 10:25 AM
Speedo drive gears	UK_Stang	Windsor Power	6	08-27-2002 04:35 AM
Gears Gears Gears!!!!	COBRAon18s	Modular Madness	20	05-13-2002 04:44 PM
Speedo gears in Super Duty T5	withamc	Windsor Power	1	03-30-2002 10:03 PM
Gears & speedo	da89cup	Windsor Power	5	01-31-2002 11:40 AM