did i damage my t-5? help!

Rick 91GT · 07-21-2001, 08:56 AM

Black Foam???? Is this Permatex that was put on to seal the shifter to the housing? If all the threads are there I guess it will be OK, but can you get a picture so we can see it. I am not a fan on JB WELD but if you think you can do that to build it back up then try it. I personally would tear it down weld it up on my Tig Welder and drill and tap the hole again, but I most likey would have to dis-assemble the tranny, to properly weld it up. The case would need to be heated then welded cast aluminum can be tricky at times.

I have done the driveway swap of the tranny, I bet that gravel is a PIA. What I do in my garage is jack it up as high as I can get it then I install the cross member to the tranny, I tape up the shifter hole then I bench press the tranny up into position (that bastard can get heavy), then once I slide a bolt through the cross member I put the jack under it, get the crossmember all bolted up, install the driveshaft and stuff then I fill the tranny through the shifter hole and then install the shifter.

------------------
Check Out My Site 91GT,Holley SysteMAX II Kit-Heads 2.02" x 1.60" port matched to a 1262,Anderson N-61,24#,76mm C&L,Full MAC exhaust 1-5/8" Long tubes,2-1/2" O.R H-Pipe,2 1/2" cat back, No A/C or PS or emissions, 12" K&N Filter,RNH PERFORMANCE Ram Air,Ron Davis Radiator,Full Suspension,S&W 8pt "X" brace,JAZ seats,3:73's,Welds..etc,4:30's and 31 splines coming very soon! FIRST TIME OUT 12.16@111 WHEELS-UP

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
VICTORY!!! Balancer Removal and Damage Photos...	Beanhead	Windsor Power	13	10-06-2003 08:54 AM
Dyno Damage	stangt00	Modular Madness	2	12-17-2002 09:30 PM
Wanna see $100k in damage???	PKRWUD	Blue Oval Lounge	21	08-13-2002 09:23 PM
Can high-torque starter damage flywheel?	Fox Body	Windsor Power	3	11-16-2001 07:09 PM
1965 289 piston damage	mitch	Classic Mustangs	2	04-23-2000 07:45 AM

07-21-2001, 08:56 AM	#3
Rick 91GT Procharged! Join Date: May 1999 Location: Hanover, PA Posts: 1,539	Black Foam???? Is this Permatex that was put on to seal the shifter to the housing? If all the threads are there I guess it will be OK, but can you get a picture so we can see it. I am not a fan on JB WELD but if you think you can do that to build it back up then try it. I personally would tear it down weld it up on my Tig Welder and drill and tap the hole again, but I most likey would have to dis-assemble the tranny, to properly weld it up. The case would need to be heated then welded cast aluminum can be tricky at times. I have done the driveway swap of the tranny, I bet that gravel is a PIA. What I do in my garage is jack it up as high as I can get it then I install the cross member to the tranny, I tape up the shifter hole then I bench press the tranny up into position (that bastard can get heavy), then once I slide a bolt through the cross member I put the jack under it, get the crossmember all bolted up, install the driveshaft and stuff then I fill the tranny through the shifter hole and then install the shifter. ------------------ Check Out My Site 91GT,Holley SysteMAX II Kit-Heads 2.02" x 1.60" port matched to a 1262,Anderson N-61,24#,76mm C&L,Full MAC exhaust 1-5/8" Long tubes,2-1/2" O.R H-Pipe,2 1/2" cat back, No A/C or PS or emissions, 12" K&N Filter,RNH PERFORMANCE Ram Air,Ron Davis Radiator,Full Suspension,S&W 8pt "X" brace,JAZ seats,3:73's,Welds..etc,4:30's and 31 splines coming very soon! FIRST TIME OUT 12.16@111 WHEELS-UP