Problems with clutch. Need help ASAP please!

Rick 91GT · 08-20-2001, 09:52 AM

Didn't realize there were 2 Hanovers? I am right below New Oxford, East of York.

If your clutch pedal feels the same then it is not the quadrant. I think your tranny is gone, maybe the imputshaft shattered, I have done that to 3 of them so far. I bought all my parts from D&D or Hanlon both nice guys to deal with. I can rebuild the tranny $250 in labor if your interested. Take a look at the topic titled T-5 rebuild whats the going rate..I listed the prices of the parts you'll need if the imput shaft did let loose. Shoot me a e-mail rhawver@strouse.com. My monitor at home died so I can't check my e-mail at home which is Rick91GT@onemain.com.

------------------
Check Out My Site 91GT,Holley SysteMAX II Kit-Heads 2.02" x 1.60" port matched to a 1262,Anderson N-61,24#,76mm C&L,Full MAC exhaust 1-5/8" Long tubes,2-1/2" O.R H-Pipe,2 1/2" cat back, No A/C or PS or emissions, 12" K&N Filter,RNH PERFORMANCE Ram Air,Ron Davis Radiator,Full Suspension, SPEC stage III clutch, Lakewood SFI bell, S&W 8pt "X" brace,JAZ seats,3:73's,Welds..etc,4:30's and 31 splines coming very soon! <B

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
CLUTCH PROBLEMS (Fork??)	drewmp28	Windsor Power	6	07-18-2004 11:51 PM
'65 - Pull Away Problems - Action Plan	geordie	Classic Mustangs	0	05-14-2002 01:43 PM
'65 Mustang - Pull Away Problems	geordie	Classic Mustangs	6	05-11-2002 04:46 PM
Clutch Problems	blue302	Windsor Power	3	09-10-2001 01:37 PM
billed 5 times to install clutch by Pauls Auto, please read and give opinions (long)	beefcake	Blue Oval Lounge	2	02-23-2001 03:05 PM

08-20-2001, 09:52 AM	#1
Rick 91GT Procharged! Join Date: May 1999 Location: Hanover, PA Posts: 1,539	Didn't realize there were 2 Hanovers? I am right below New Oxford, East of York. If your clutch pedal feels the same then it is not the quadrant. I think your tranny is gone, maybe the imputshaft shattered, I have done that to 3 of them so far. I bought all my parts from D&D or Hanlon both nice guys to deal with. I can rebuild the tranny $250 in labor if your interested. Take a look at the topic titled T-5 rebuild whats the going rate..I listed the prices of the parts you'll need if the imput shaft did let loose. Shoot me a e-mail rhawver@strouse.com. My monitor at home died so I can't check my e-mail at home which is Rick91GT@onemain.com. ------------------ Check Out My Site 91GT,Holley SysteMAX II Kit-Heads 2.02" x 1.60" port matched to a 1262,Anderson N-61,24#,76mm C&L,Full MAC exhaust 1-5/8" Long tubes,2-1/2" O.R H-Pipe,2 1/2" cat back, No A/C or PS or emissions, 12" K&N Filter,RNH PERFORMANCE Ram Air,Ron Davis Radiator,Full Suspension, SPEC stage III clutch, Lakewood SFI bell, S&W 8pt "X" brace,JAZ seats,3:73's,Welds..etc,4:30's and 31 splines coming very soon! <B